IF YOU KEEP BURNING UP 5HP 184T FRAME 208-230V MOTORS DUE ON YOUR 208V INCOMING POWER SUPPLY, THIS MOTOR IS YOUR SOLUTION. STANDARD 5HP SINGLE PHASE 208-230V ELECTRIC MOTORS HAVE A 1.15 SERVICE FACTOR AT 230V AND A 1.0 SERVICE FACTOR AT 208V INCOMING VOLTAGE. WHEN YOU CONNECT A 208-230V MOTOR TO A 208V OR UNDER POWER SUPPLY, YOUR'RE RUNNING THAT MOTOR AT THE VERY HOTTEST AND HARDEST ITS CAPABLE OF RUNNING WITH A 1.0 SERVICE FACTOR.  SOMETIMES BEYOND ITS SERVICE FACTOR CAPABILITY. IF YOUR INCOMING VOLTAGE DIPS BELOW 208V, CAN AND WILL CAUSE DAMAGE TO THE MOTOR. THIS MOTOR IS RATED 200V WITH A 1.15 SERVICE FACTOR AT 200V. SO WITH THE NEMA (NATIONAL ELECTRIC MOTOR ASSOCIATION) RULES OF 10% DEVIATION OF VOLTAGE FOR ELECTRIC MOTORS IN THE UNITED STATES, YOU CAN USE THIS 200V MOTOR AS LOW AS 190VOLT AND NO HIGHER THAN 220V INCOMING VOLTAGE. IF YOU HAVE A 5HP SINGLE PHASE 184T 208-230V MOTOR AND YOUR INCOMING VOLTAGE IS 208V AND SOMETIMES LOWER. THIS MOTOR IS YOUR BEST SOLUTION. ITS SPECIFICALLY DESIGNED TO RUN AT THAT LOWER VOLTAGE WELL WITHIN ITS 1.15 SERVICE FACTOR. THIS 200V MOTOR WILL LAST MUCH LONGER. 

THIS 5HP MOTOR COMES ON A 184T FRAME AND ROTATES AT 1750 RPM. THIS MOTOR IS REVERSIBLE AND CAN BE WIRED TO ROTATE EITHER CW OR CCW. THIS IS AN OPEN DRIP PROOF MOTOR AND IS INTENDED TO BE USED IN DRY, NON-DUSTY INDOOR ENVIRONMENTS. THIS MOTOR IS BACKED BY A FULL 18 MONTH MANUFACTURERS WARRANTY FROM DATE OF SALE. WEG STEEL FRAME COMPRESSOR DUTY ELECTRIC MOTORS SET THE STANDARD FOR HIGH TORQUE, HIGH PERFORMANCE AND ARE WELL SUITED FOR APPLICATIONS THAT REQUIRE A HEAVY STARTING LOAD. CAPACITOR START TYPE MOTORS LIKE THIS ALLOW FOR HIGH STARTING TORQUE. THIS MOTOR IS NOT MADE IN CHINA. 

PLEASE MAKE SURE THE ELECTRIC MOTOR YOU ARE REPLACING MATCHES THE HP SPECS, THE FRAME SIZE AND RPM OF THIS MOTOR.  

WHY YOU ALWAYS NEED A MAGNETIC STARTER ON INDUSTRIAL GRADE MOTORS. A MAGNETIC STARTER IS ALWAYS REQUIRED ON ANY 5HP 184T FRAME MOTOR AND LARGER. WIRING AN INDUSTRIAL SIZE MOTOR THROUGH THE PRESSURE SWITCH ALONE, IS NEVER A GOOD IDEA, AND HERE'S WHY. PRESSURE SWITCHES DO NOT COME WITH OVERLOAD PROTECTION FROM POWER SURGE OR LIGHTING. IN ADDITION, PRESSURE SWITCHES HAVE VERY SMALL CONTACT POINTS THAT CONNECT TO THE MOTOR. SMALL CONTACT POINTS CAN STARVE YOUR MOTOR OF THE NECESSARY POWER IT REQUIRES TO START AND RUN NORMALLY. MAGNETIC STARTERS NOT ONLY PROVIDE YOU WITH MOTOR PROTECTION FROM POWER SURGE AND LIGHTING, THEY ALSO HAVE LARGER CONTACT POINTS THAT CONNECT TO YOUR ELECTRIC MOTOR. ALLOWING FOR A STEADY FLOW OF CURRENT THAT AN INDUSTRIAL GRADE MOTOR REQUIRES TO RUN AND ESPECIALLY START UP. BY INCORPORATING A MAGNETIC STARTER WILL ALLOW YOUR MOTOR TO LAST MUCH MUCH LONGER. 

PLEASE VISIT OUR EBAY STORE FOR THE BEST PRICE AND SELECTION OF MAGNETIC STARTERS. 

 5HP  -  184T FRAME  -  1750 RPM  -  SINGLE PHASE  -  200 / 208 VOLT  -  1-1/8" SHAFT DIAMETER  -  2.75" SHAFT LENGTH  

  MADE IN BRAZIL

TECHNICAL INFO:

HORSEPOWER: 5

AMPERAGE: 23.8 FULL LOAD AMPS AT 200V

PHASE:  SINGLE PHASE

VOLTAGE: 200 / 208

RPM: 1750

BASE:  REINFORCED STEEL FIXED BASE

FRAME:   184T

SHAFT DIAMETER: 1-1/8" KEYED SHAFT

SHAFT LENGTH:  2.75"

ROTATION:  REVERSIBLE  CW OR CCW ROTATION

FREQUENCY: 60HZ

SERVICE FACTOR: 1.15 @ 200V

ENCLOSURE: ODP  OPEN DRIP PROOF 

CONSTRUCTION: STEEL FRAME CONSTRUCTION

WEIGHT: 102 LBS

WARRANTY: 18 MONTH

ADDITIONAL PRODUCT INFORMATION:  MADE IN BRAZIL  -  CAPACITOR START ALLOWS FOR HIGH STARTING TORQUE