Feature Products

2*100W OCL Two Channel Amplifier Board Module High Power Electronic DIY Kits

 
Features:
Fully separated components, four high-power triodes, two stereos, each with a power of up to 100W.
This power amplifier adopts the typical OCL circuit, which has the advantages of high stability, wide frequency response range and good fidelity. It is often used in high-fidelity sound reproduction equipment. This OCL stereo amplifier is suitable for use by a wide range of electronic enthusiasts and audiophiles.

First, the working principle of the circuit
As can be seen from the figure below, the output of the speaker and the amplifier is directly coupled, and the output capacitor for DC blocking is omitted. In order to make the DC potential of the output of the circuit zero volt, a positive and negative symmetrical power supply is used, and the differential amplifier input is used. And other measures. In Figure 1, vt i, vt2 are differential amplification input stages, vt3 is the excitation stage, and vt4~vt7 are composite complementary output stages. The audio signal is sent to the base of vt i through the coupling capacitors c 1 and ri. After amplification, it is output from the collector of vt i and sent to vt3 to further increase. The excitation signal of the collector output of vt3 pushes the power output stage vt4~ Vt7 works so that the amplified audio signal can drive the speaker to work.

To facilitate further analysis, Figure 1 can be simplified to the form of Figure 2. Vt4 and vt6 are combined to be equivalent to one npn transistor, and vt5 and vt7 are equivalent to one pnp transistor. It can be seen from the vt4, 6 and vt5, 7 of the circuit of Fig. 3 and the power supply filter capacitors c9, c10 that they are equivalent to a bridge. When vt4, 6, vt5, and 7 are identical, c9 and c10 are also identical, the bridge arms are balanced, and the speaker does not pass through. If the positive and negative power supplies are completely symmetrical, the output potential can be guaranteed to be 0V.

Since the circuits are all directly coupled, any changes in ambient temperature and component parameters will affect the potential at the output (point a, Figure 2). To this end, vt 1, vt2 constitute a differential amplifier to overcome the zero drift, DC negative feedback is also applied in the circuit, that is, the output is applied to the base of vt2 through r6, so that the potential of the output (point a) is zero. Volt. The feedback process is: a point potential ↑—ube2 ↑—ie2 ↑—ur4 ↑—ube l ↓一ic l↓一uc 1 ↑—ube3 ↓一ie2 ↓—ur7↓一ube4,6 ↓(ube5,7 ↑) A vt4, 6 internal resistance v (vt5, 7 internal resistance ↓) a point potential ↓. On the other hand, if the potential at point a is ↓, the potential at point a will be paralyzed by the opposite change process.

Second, the installation and production
The printed circuit diagram of this circuit is shown in Figure 3. It includes a two-way OCL power amplifier circuit and a DC power supply circuit. A heat sink is required between the body of the 4 high power tube 2N3055 and the printed circuit board, and is fixed by screws. The resistors are installed horizontally. The capacitors and triodes are installed vertically and close to the circuit board. The soldering requirements are firm and reliable. There are two jumpers on the circuit board, which can be soldered with iron wires.

Third, debugging
The power transformer used in this circuit needs to be prepared by itself. It adopts a center-tapped dual output transformer (AC: 1 5VX2), the power is not less than 40W, and is connected to the AC~ and the upper part of the printed circuit board. After being energized, it is generated at both ends of C9 and C10. With a DC voltage of ±18V, the voltage across the speaker is zero volts.

First adjust the current of the differential amplifiers vt l, vt2, in order to avoid the large current flowing through the power tube, first short the base of vt4, vt5 with a wire, so that vt4 ~ vt7 cut off. Then solder one end of the resistor r6 to the ground and solder it to ground. The total emitter current of the differential amplifier stage is determined by r4. The R4 is adjusted so that the total emitter current of vt 1 and vt2 is 1 mA. After the resistor r6 is restored, the voltage across the speaker should be o. If there is an offset, adjust r3.
 
Package Included:
1 x OCL Amplifier Board DIY Kit
1. We Ship to Worldwide
2. We ship your orders within 1-2 business days after the payment cleared.
3. Item shipped from China via china Post Airmail, reach most of the countries within 2 to 4 weeks.
4. Delivery time depends on destination and other factors, it may takes up to 20 days. If you don't receive
the item after 30 days,please keep in touch with us, we'll investigate and solve the delivery problem.
5. Import duties, taxes, and charges are not included in the item price or shipping cost. These charges
are the buyer's responsibility. Please check with your country's customs office to determine what these
additional costs will be prior to bidding or buying.
 
ShenZhen

1. We accept PAYPAL only.
2. Payment must be made within 7 days of auction closing (Unpaid dispute will automatically open when item
is not paid in 7 days).
3. PLEASE NOTE: SHIPPING&HANDING DOES NOT INCLUDE DUTIES, LOCATL TAXES OR ANY OTHER IMPORTATION FEES.
4. Please list your special requests (color, packages, value of declaration, etc.) in the EBAY NOTES SECTION
when you make payment

 

1. Customer satisfaction is our top goal. All products are quality checked. They are new and in good
condition when shipped to our customers. If product is defective or damage upon arrival, or wrong
product shipped, please keep in touch with us immediately. Returns accepted within 14 days of delivery date
and item must be in original new condition, not worn or altered in any way with attached tags & wrap.
Otherwise deal is final. Return shipping must be paid by buyer.
2. Please keep in touch with us first if you have anyproblems/questions/concerns. We will be happy to resolve
any issues you may have in a cordial and friendly manner.
3. We appreciate your Positive Feedback, and will do the same in return. PLEASE DO NOT leave
negative feedback without first communication with us. Please allow max 24 HOURS for us to respond

We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is
very important to us. We request that you keep in touch with us immediately BEFORE you give us neutral or
negative feedback, so that we can satisfactorily address your concerns.It is impossible to address
issues if we do not know about them!

DataCaciques