A: 6 heat pipes, RTX5700XT/5700 RGB light, original 4pin light lead

B: 6 heat pipes, RTX5700XT monochromatic light, 2pin light lead of the graphics board

C: 6 heat pipes, RTX5700 monochrome lamp, send 2 in 1 wire

D: 5 heat pipes, RTX5700XT/5700 RGB lamp, original 4pin lamp lead

E: 5 heat pipes, RTX5700XT monochromatic lamp, graphics board 2pin lamp lead

F: 5 heat pipes, RTX5700 monochrome lamp, send 2 in 1 wire

G: 6 heat pipes, RX VEGA 56/64 RGB lamp, original 4pin lamp lead

H: 6 heat pipes, RX VEGA 56/64 monochromatic light, 2pin light lead of the graphics board

I: 6 heat pipes, RADENO VII RGB lamp, original 4pin lamp lead

J: 6 heat pipes, RADENO VII monochromatic lamp, 2pin lamp lead of the graphics board

K: 6 heat pipes, RTX2080 RGB light, original 4pin light lead

L: 6 heat pipes, RTX2080 monochromatic lamp, send 2 in 1 wire

M: 6 heat pipes, RTX2080 Ti RGB light, original 4pin light lead

N: 6 heat pipes, RTX2080 Ti monochromatic lamp, send 2 in 1 wire

1. This radiator is DIY modified with ASUS Raptor GTX10 series radiator. Buyers who do not accept modifications should be careful! After the modification, the RX5700XT/RX5700/RX VEGA64/RX VEGA56/RADENO VII and RTX2080Ti/RTX2080 graphics cards of the public version architecture (non-public version cannot be installed) of various brands can be installed, please compare and buy in the link color classification.

2. The fan power supply lead is the standard four-pin interface of the graphics card with temperature control and automatic start and stop functions (the default general GPU temperature is about 55-60 degrees and starts to start, and the fan stops at a temperature lower than the default temperature to save energy and mute). After the installation is complete, the driver fan needs to be updated or restored to start normally. Please pay attention to this point when installing. RTX2080/2080Ti card without a four-pin fan power socket (the original fan is powered by a 14-pin socket) to install this radiator fan needs to be switched to the motherboard fan power socket for power supply, please contact customer service for consultation.

3. The thermal pad of the radiator with the video memory part can take into account the heat dissipation of the video memory (except for the integration of RX VEGA56/64 and RADENO VII video memory with the GPU chip). All radiators do not have a heat dissipation position for the power supply part. For cards without a power supply heat sink, it is recommended to purchase a heat sink and attach it to the MOS tube to assist in heat dissipation.

4. The original version of the upper shell light bar of the radiator has RGB function. Since the graphics board of the public version of the card does not have RGB light power supply sockets and does not support RGB functions, RGB cannot be realized. The lights can only achieve red, green and blue monochrome. The shop provides three light power solutions to meet the needs of different buyers. .

Option 1 (RGB lamp original four-pin lamp lead): suitable for cards with RGB lamp (12V) power supply socket on the motherboard (the RGB lamp on the radiator is powered by 12V, and the motherboard is powered by 5V). The radiator distributes the RGB lamp extension lead to the mainboard RGB lamp power socket for power supply and then synchronizes with the mainboard to realize RGB. Due to the wide variety of motherboards, the sockets and line sequence are different, the motherboard end of the RGB lamp extension cord delivered by the store is a DuPont split four-pin socket (other sockets on the motherboard end are not currently supported, and the buyer needs to transfer by themselves)

Scheme 2 (Monochrome lamp and two-pin lamp lead of the graphics board): Applicable to the card with a two-pin lamp power supply socket on the graphics board. Change the lead of the radiator and plug it directly into the original two-pin lamp power supply socket of the graphics board to power the light. Note that the light can only be lit in red, green, and blue, and it cannot achieve RGB. Please leave a message or Inform the customer service to choose the color of the light, and the light will be red by default.

Solution 3 (Monochrome lamp with two-in-one lead): It is suitable for cards that do not have lamp power sockets on the motherboard and graphics board. The radiator distribution fan and lamp two-in-one lead plug into the graphics board fan power supply socket to light up the light, the light can only choose one of red, green, and blue to light up and cannot achieve RGB, please inform customer service or leave a message Select the light color, the default light is blue.