Welcome to Atlanta Pro Sound |
Brand New Replacement Belt for
TEAC Reel to Reel models
- X-10
- X10
- X-10R
- X10R
- X-10R II
- X10R II
These X-10 models all use the same belt.
This is a relisting of a popular eBay item, not a new listing. This item was listed as eBay Item #182714984018. I sold 48 of them, I have 48 very happy customers! Then the listing mysteriously disappeared.
Available as Buy it Now
one (1) brand new replacement Drive Belt for TEAC open reels, TEAC models X10, X10R, X-10, X-10R, X-10R Mk II, X-10R Mk 2.
There is a myth that one belt fits 95% of all Reel to Reels. In reality, nothing is further from the truth. (It is also a myth that all TEAC Reel to Reels take the same belt!!! Ha!) A belt that is ½ inch too large or small will probably run on your open reel deck, but if it is too small, there may be too much little pressure pulling the tape, it will wear out your motor years before it would under normal conditions. If it is too large, there may be too little pressure pulling the tape, and it might also be bad for the motor, but as belts get older, they expand, so in the best case, you need a replacement years before you should. Either way, it is bad.There are people online who have been selling belts for 10-15 years. Many have lots of feedback or have websites thatlook like they know what they are doing. Do they really know what belt is the match for your open reel? TEAC quit giving technical support on the models X10 and X10R (including part numbers) over a decade ago. When the models X-10, and X-10R rolled off the assembly line, I was Assistant Store Manager for the largest independent TEAC dealer in the Southeastern US. My information came from the TEAC Factory Repair Station in Atlanta, Georgia (note, I did not say factory authorized repair station, those were private companies in Atlanta, like HENCO and Norman's.) My information came from Yoshi, the man that ran the TEAC Repair center, his training was from TEAC Corporation in Tokyo (TEAC is an acronym for Tokyo Electronic Acoustic Company. I have fond memories of Yoshi driving his bright yellow Trans-AM up and down Buford Highway at speeds that were significantly above the speed limit! He loved that car. Read the Seller History below for more information.
(In case you are wondering, I really do know that the dash in the model number comes after the X. I enter the model with the dash in different so those who search for the model can find it regardless of if they have the dash in their search!)
5 Belt Measurements
All flat rubber belts have 5 measurements that affect the belt's performance.
Length is the one most people think of right away. Length affects how tight the belt is. If it is too tight, the motor will not run (or if it is just a little too tight, the motor will wear out quickly).
Width is one you might not think is important, however, the manufacturers specify this one down to the 64th of an inch! If the belt is too wide, the risk is the belt will hit the outsides of the capstan, which will create momentary bumps in the speed. If the belt is too narrow, it does not have enough contact with the capstan, causing it to slip. Either of these problems may be inaudible at first, but as the belt ages, who knows?
Thickness of the belt is the smallest of the measurements. Most Turntable belts are close to the same thickness, but an el cheapo parts provider, who has only a decade of experience, might buy their belts based on length and get the one that costs them less regardless of the thickness that meets original specifications. You could get a belt that they bought wholesale at 99¢ but is way too thick! A belt that is too thick will not fully fold around the capstan, causing more pitch problems. If you call to complain, you are told that your turntable has natural Wow and Flutter. Friends: These models are closed-loop, dual capstan. Wow and Flutter is sixteen (16) times below the audible limit
(½ of 1% wow and flutter is not audible with normal music -- Sources: Julian Hirsch - Hirsch-Houck Labs and the TEAC models X-700 and X700R Service Manuals.)
Don't let them pull the wool over your eyes! If you hear wow and flutter (a.k.a. bad speed fluctuation), you might just have the wrong size belt!
External Diameter . This one is a no-brainer, it is closely related to the thickness and internal diameter.
Internal Diameter. Like #4, this one is also a no-brainer, it is closely related to the thickness and external diameter.
Many old-style belts were cut to size. Modern (get it out the door as fast as you can) cutting techniques can lead to inconsistencies and inferior product.
This belt is not cut, it is precision molded to meet original factory specifications for the Technics X-700, X700R.
My distributor, Artistic Audio of Atlanta, buys thousands of belts made by this company and has been sending them all over the United States for many years. Every few of weeks Artistic Audio of Atlanta reorders belts buy the hundred, replacing the stock they have sold. No belt has been on their shelf more than a few weeks. Because they come into the distributor regularly, I can personally guarantee that the belt you get is
fresh!
About these Models:
This section of this page is Under Construction.
The belts are in stock, we are shipping them the evening after they are ordered.
Check back soon!
Are you about to purchase one of these models? The three DC servo motors are built like tanks, and rarely need any service. Usually the drive belt (offered here) and the counter belt are the only things that need replacement. You won't know if you need a counter belt, until the drive belt is replaced. If you have any concerns, feel free to send me questions using the "Contact Seller" button under Seller Information on the top right side of this page.
Belts are shipped by USPS Ground Advantage (2-5 Day expected delivery).
Please, ask in advance about international shipping.
Priority Mail shipping to the US is available for $9.65.
Most items are shipped within 1 business day.
Thanks in advance for your purchase!