Note: The voltage is 90V-220V, please confirm your local working voltage and then buy, thank you very much!

Only supports Celsius temperature display
 
There are three styles of the White Wireless WIFI Thermostat Touchscreen
Gas boiler thermostat (A thermostat + main receiver)
Electric heating(A thermostat + main receiver)
Water heating(A thermostat + main receiver)


We have two options:

1: You can choose one thermostat to control the temperature of a room, so for several rooms, you can purchase several sets of (A thermostat + main receiver), and their temperatures can be set and controlled separately.

2: You can also choose multiple sub-receivers to be placed in different rooms to control the temperature of multiple rooms at the same time. A set of thermostat + main receiver, and then + (N-1 )sub-receivers (buy several-1 for several rooms),In this way, all rooms can only be set with the same temperature.

So receiver 1, receiver 2, 3,4... can be placed in different bedrooms. If there are several bedrooms, you can consider purchasing (N-1 )sub-receivers. They can be controlled separately, for example, room 1 and room 4 turn off heating, room 2 and room 3 turn on heating, but the temperatures in all rooms must be consistent because they are the temperatures set by the same thermostat.

 
RF Wireless WIFI Thermostat Smart Thermostat Working principle:
use the thermostat to control the receiver to control the indoor temperature!
The thermostat can be installed in the bedroom living room dining room bathroom..
 
You can also use your mobile phone to control the thermostat from anywhere, whether at the airport, travel, or work, as long as your phone can be connected to the Internet. The thermostat can also control with your voice by Alexa and Google home !

 Download “Smart RM” or “Smart life” app from Google play and app store.
 

Product Specification

☆ Power: Receiver: 90V-230Vac 50/60HZ 

Thermostat: USB power supply/4*AAA Batteries

! Pls remove batteries when USB power is working. 

☆ Display accuracy: 0.5°C 

☆ Insulating condition: Normal environment

☆ Probe sensor: NTC(10k)1% 

☆ Running program: Set per 1 week as a cycle 

☆ Contact capacity: 5A/90V-250V(Water heating，Boiler 

 heating);16A/90V-250V(Electric heating) 

☆ Output: Switch relay

☆ Working environment temperature: 0~70°C 

☆ Installation: Wall mounted or on battery seat

☆ Range of temperature adjustment: 5~35°C 

☆ Size(mm)：130*90*25


 Receiver Indicator Light

Power indicator (green): Power on receiver, green light always on; turn off receiver, the green light is on for 1 second and off for 1 second.

RF signal indicator (orange): It is always on within 10 seconds after power-on.After the pairing is successful, the signal light will be off; or if no pairing is performed within 10 seconds It will automatically turn off; when it is working normally, the light will flash when it receives a RF signal. 

Load/fault indicator (red): In normal operation, the load output is turned on, the light is on, and the load output is off, and the light is off; when there is a fault, it blinks and the alarm is indicated as follows:

RF signal indicator (orange): It is always on within 10 seconds after power-on.After the pairing is successful, the signal light will be off; or if no pairing is performed within 10 seconds It will automatically turn off; when it is working normally, the light will flash when it receives a RF signal. Load/fault indicator (red): In normal operation, the load output is turned on, the light is on, and the load output is off, and the light is off; when there is a fault, it blinks and the alarm is indicated as follows:

WIFI signal indicator (blue): When WIFI data is received, it will flash once; continuous fast flashing means it is in WIFI EZ network configuration mode; continuous slow flashing means it is in WIFI AP network configuration mode; it will always be when the network is successfully configured. On; when the WIFI is abnormal, it will flash twice quickly, and the interval will be off for 2 seconds

Query receiver IP: Within 10 seconds of power-on short press the “push” key or long press the “push” for 3 seconds in normal working state, you can query the current receiver IP address, the IP address is displayed by the indicator light, and the specific display sequence is as follows:

All indicator lights show for 1 second -> show IP address for 10 seconds (see the IP address table below) -> all off for 0.5 second -> return to normal display

PushAuction