eBay

Brand:Eletechsup

Product Name:DC12V 1 Chanel Receiver Relay Modules 433.92MHZ & Wireless Key Fob remotes

QTY:1 pcs remotes and 4 pcs Receiver Controller . ( This remote doesnot have a battery inside)

Technical indicators:

1.operating voltage: DC 12V ;

2.working frequency:433.92MHz;

3:Maximum load: 1000 watts;

4:PCB Size:41×20×15mm;

5: Momentary Mode ,Latch Mode , Toggle Mode can be adjustable by slodering back side.

6. Pls connect the receiver modules properly before power supply ;

8: Momentary Mode ,Latch Mode , Toggle Mode can be adjustable by jumper .
9. Pls connect the receiver modules properly before power supply ;
10: 1 chanels;
11: Learning function (can works with EV1527 and PT2262 remote , can store 16 pcs different code remote );

Advantage :

1: Receiver Mother board have a learning key , if the remote is lost , must buy EV1527 Learning remotes to re-learn;

Output:

A.singnal Inter-locking (Latch)----connect 2 and 3 ;

B.singnal Self-locking (Toggle) ---- connect 1 and 2 ;

C.singnal Non-locking (Momentary ) ---- All disconnect ;

· Toggle : Press->On; Press again->Off ;

· Latched : Press->On; Press other button->Off ;

· Momentary : Press and hold->On; Release->Off ;

Relay mode :

Normally close (NC ) ;

Normally open (NO ) ;

Normally-open (NO) contacts connect the circuit when the relay is activated; the circuit is disconnected when the relay is inactive. It is also called a Form A contact or "make" contact. NO contacts may also be distinguished as "early-make" or NOEM, which means that the contacts close before the button or switch is fully engaged.
Normally-closed (NC) contacts disconnect the circuit when the relay is activated; the circuit is connected when the relay is inactive. It is also called a Form B contact or "break" contact. NC contacts may also be distinguished as "late-break" or NCLB, which means that the contacts stay closed until the button or switch is fully disengaged.

Learning method and steps

1. Keep pressing learnig key on receiver board , release the button when LED is off , enter the learning state ;

2. Press any key on remote control within 5 seconds , LED flash 3 times and then turn on , then it have success in learning .

Clear the deposit information

Keep Pressing Learning Key , LED turns off , Wait 10 Seconds , LED turn on , that deposited information has been successfully cleared ;

Transmitter :

Feature:

1. Four buttons;

2. High stability, SMT chip, frequency stabilization SAW, 6.5G ultra-high-frequency transistor;

Technical Data :

Power supply : 12V 23A battery replacable .(This remote doesnot have a battery , Please buy in your local market )

Operating current: ≤ 9mA;

Decode Type : land or pad;

Oscillation mode: SAW resonator;

Modulation mode:ASK;

Operating frequency:433.92MHZ ;

Encoding IC : Fixed code SC2262（Compatiable PT2262、PT2264） ;

(CANNOT program , HAVENOT Learning Function , Cannot copy your existing remote ,Can be duplicate if your receiver board have a learning key ) ;

RC Resistance : 4.7M;

Remote size: 58×39×16 mm;

Typical Applications

• Automotive alarm systems

• Automotive RKE systems

• Automotive immobilizers

• Gate and garage door openers

• Identity tokens

• Burglar alarm systems

Wiring Diagram 1:

DC 12V control circuit,Wiring diagram below. "LOAD" may be LED lights, fans, motors and other DC 12V

Wiring Diagram 2:

DC 1-48V OR AC 85-265V control circuit,Wiring diagram below(Note:If not DC 12V load, need another DC 12V power supply). "LOAD" may be LED lights, fans, motors and other DC AC equipment