Why Choose Our Paintless Repair Tool Kits?
Save time, save money. No more paying for body shop repairs! Glue gun and glue sticks included, full professional accessories, no need to buy glue gun
and glue sticks separately.
|
|
|
|
|---|---|---|---|
Wire Board The dent repair reflector board is used to check the dent on the flat car surface, and the position of the dent can be found by the alignment line. When the distorted image or line becomes parallel in the reflection, it means that you have successfully removed the dent. | T-Bar Hammer Repair Tool Anyone can handle the removal of dents, easy to use. Adopts a lever-type design for dent repair works. It can be decomposed into two different T bar, clever two ways of use. | Dent Repair Tool The distance between the brackets can be adjusted, specifically to repair the dent size of 3-5cm. | Bridge Dents Repair The feet are equipped with two rotating wide-angle pedals to ensure that our products can work on surfaces of different shapes. |
Professional car repair kits
Save money and enjoy your time as you see these recovering dents from your car like it has never been damaged before.
All repair tools and accessories are complete.
Glue gun and glue sticks, yellow line board reflector board, dent puller, glue tabs, clean rubber cloth for rubber hammer, plastic tab pen, etc. included in the package.
The yellow Line Board reflector panel is a good help in check the dent. Widely used in car dent repair detection, this tool gives you a better view of the area you are working on to repair car dents and dents. It is also suitable for all kinds of metal surface, such as automobile, motorcycle, refrigerator, washing machine, etc.
Steps for usage:
1. Clean the surface with a clean damp cloth.
2. connect the power source and use the glue stick to andpreheat for 5-10 minutes.
3. According to the dent size to choose the Glue Puller Tab, then put the heated glue on puller tab, immediately place puller tab in the center of the dent and hold on until it sticks.
4. Let the glue cool for about 8-10 minutes. The cooling time should be less than 10 minutes and should be shorter slightly in winter.
5. After the glue cooling, use a black dent lifter or bridge dent puller to align and press the puller to pull up the dent. Repeat the above steps until the dent disappear.
6. After finishing the dent, use the 95% alcohol to clean the residual glue which on the car surface with plastic shovel.
Does this dent puller hurt the original car paint?
Professional design to avoid damage to car paint, this is not to hurt paint depression repair tools.
How big is the depression that this tool can fix?
This is a small dent repair tool that can be repaired in 1-3 inches.
Could I use this tool to fix dent in some places?
It can repair car body, motorcycle, refrigerator, washing machine, stainless steel door, metal surface damage repair etc.
What should I do if it doesn't work during the repair process?
You can get professional guidance and we offer a year-round after sales service for this paintless dent repair kit.
Can a non-professional car repairer buy it?
This dent removal tool is suitable for all people who are willing to work manually. It only takes four steps and is very simple and convenient.
Step-By-Step Instructions for Using the Paintless Dent Repair Kit
| Step1 | Prep tabs by soaking them in 91% rubbing alcohol and drying them before first use. |
| Step2 | Insert a glue stick into the glue gun. Plug in the glue gun and allow it to heat up for 5 minutes. |
| Step3 | Clean the area to be repaired with 91% isopropyl rubbing alcohol and a clean towel. |
| Step4 | Select the correct sized dent pulling tab by comparing it to the size of the dent. |
| Step5 | Apply hot glue to the dent pulling tab by pulling on the trigger of the glue gun until approximately a dime sized amount of glue is released. |
| Step6 | Apply the dent pulling tab to the exact center of the dent. Avoid applying too much pressure when placing the dent pulling tab to the dented area. |
| Step7 | Allow the glue to set for about 5 minutes. If your fingernail leaves an impression in glue, simply allow a couple more minutes for glue to harden. |
| Step8 | Slide the dent lifter device directly over the dent pulling tab shaft until the female adapter in the center of the dent lifter slides over the shaft of the tab. Adjust the height knob accordingly. |
| Step9 | Squeeze the dent lifter handle slowly several times until the desired result is achieved. |
| Step10 | It is common for the dent pulling tab to release from the glue, leaving the glue on the panel of the vehicle. When this occurs, spray 91% rubbing alcohol on the edge of the glue and peel it away using the plastic scraper. |
| Step11 | Occasionally a high spot is created when pulling the dent. If this were to happen, gently tap down any high spots using the dent hammer and the plastic tap down tool provided, until the dent is flush. |
1×2in1 T-bar slide hammer dent puller-----for big dents
1×Adjustable Silver Bridge Puller-----for middle dents
6×metal Puller Tabs
1×hot melt glue gun
5×yellow glue stick
5×black glue stick
1*wire board-----for checking dents(no power source)
1×Rubber Hammer
1×Tapdown Set with 5 Heads
37×Black Puller Tabs----for all kinds of car dents
1×White Cotton Gloves
1×Empty Alcohol Bottle
1×Small Triangle Plastic Shovel
1×Dishcloth
1×PDR Tools Bag
1×User Manual
