These boxes enable to connect a non-B&O source to a BeoLab speaker, it will switch On and Off the BeoLab speaker automatically when a small audio signal is detected at the input (or when music is sent via the Bluetooth) and switches OFF (standby) after 3.5 minutes after audio stops. (Made with dedicated audio trigger IC, similar on/off trigger concept used in commercial subwoofers. Prolongs speaker lifespan and saves energy, when the speaker is left switched on continuously, the electronics will fail quick).

NOTE: There is a 7 working days handling+ delivery time, Thank you for patience !

This trigger circuit is more sensitive and reliable at low volumes than the trigger circuits found in BeoLab speakers.

For all PowerLink Mk3 compatible BeoLab speakers like BeoLab 1, 2, 3, 4, 7.1, 7.2, 7.4 7.6,  BeoLab 9, 10 and Subwoofers like Beolab 2 and 11, BeoLab 4000, 6000, 8000.

These boxes will connect with your own PowerLink cables, If you do not have Powerlink cables, I have trigger cables to connect BeoLab to non-B&O device with 12vTrigger output and cables with built in automatic trigger circuit:

With 2 x DIN to connect two BeoLab speakers: www.ebay.co.uk/itm/175197162760

With 1 x DIN to connect one BeoLab speaker: www.ebay.co.uk/itm/175157622816

Adaptor Box Models:

• Universal-RCA-2xDIN-12V trigger- Dual DIN PowerLink splitter with 3.5mm minijack 12V trigger input & Ground loop isolator switch (most of the time is not needed to isolate, but some receivers need isolation to reduce noise). Connects to the 12V trigger output of the non B&O equipment with a minijack interconnect cable (mono or stereo, cable not supplied). Keeks the BeoLab speakers ON when the non B&O equipment is ON.
• BeoLab 7 - RCA Inputs only-Audio signal Trigger- Ideal for BeoLab 7 series, but good with any other BeoLab, with RCA stereo inputs, with speaker On/Off LED. The power cable can be removed/replaced. Works with 110-230V.
• BeoLab 7 - 3.5mm Minijack input only-Audio signal Trigger-Ideal for BeoLab 7 series, with 3.5mm minijack socket input, with speaker On/Off LED, ideal to connect to TV with headphone output. The power cable can be removed/replaced. Works with 110-230V.
• BeoLab 7 - Bluetooth & 3.5mm minijack-Audio signal Trigger- same like above with added Bluetooth 5.0 receiver (passive mixer allows to keep all connected at the same time), volume control from the source. Fitted with Bluetooth On/Off switch and speaker On/Off LED, ideal to connect to TV with headphone output.  Works with 110-230V.
• BeoLab 2 with RCA Inputs only-Audio signal Trigger- Ideal for BeoLab 2,9, 10, 4000, 6000, 8000, same like for Beo7 but with added power connection, no need for separate power lead, with RCA stereo inputs, with speaker On/Off LED.  Works with 110-230V.
• BeoLab 2 - Bluetooth & 3.5 Minijack-Audio signal Trigger-same as above, with 3.5mm minijack socket input, with speaker On/Off LED.  Works with 110-230V.
• Universal RCA-1xDIN-Audio signal Trigger- universal for all BeoLab speakers when you want to use your own PowerLink cables (mk.3), with RCA stereo inputs, speaker On/Off LED, needs power from a USB-C phone charger, Google Chromecast USB power supply recommended to avoid noise.
• Universal RCA-2xDIN-Audio signal Trigger- with dual DIN sockets to connect to two BeoLab speakers (Powerlink splitter), with RCA stereo inputs, speaker On/Off LED, needs power from a USB-C phone charger , Google Chromecast power supply recommended to avoid noise. 
• Universal BT-jack & 1xDIN-Audio signal Trigger- same as above but fitted with 3.5mm minijack socket and with added Bluetooth 5.0 receiver (passive mixer allows to keep all connected at the same time), volume control from the source. Fitted with Bluetooth On/Off switch and speaker On/Off LED. Google Chromecast power supply recommended to avoid noise.
• TV ARC-Single DIN MALE plug-40cm cable (please contact for different lengths)-ideal to connect to BeoLab 7 series, BeoLab 2, 10, 11. These TV-ARC boxes connect to the back of the TV-ARC HDMI socket (HDMI cable not included) and the volume will be set from the TV remote (may need setup from TV menu-check TV manual). The box will need 5V Power and will connect to the TV USB socket with the supplied USB cable.
• TV ARC-Single DIN FEMALE connector-15cm cable- connects to a PowerLink cable extension into any BeoLab speaker, can connect multiple speakers using powerlink splitter.
• TV ARC-Dual DIN (splitter) FEMALE connectors-15cm cables- connect to PowerLink cables to two Beolab Speaker like BeoLab 4000,6000, etc. 

I have a short description of how it works on Youtube : https://youtu.be/b9SgnyxI7HA?si=xCPTMFixygkT92Qw

Thoroughly tested, comes with 30 days return if you are not happy. Please message with your system details to decide what is best for you, happy to answer any questions.

Free post to UK..

Worldwide post.

Also, Ebay Global shipping programme (total shipping cost and fees will be calculated by ebay when check out, please message if you have question regarding delivery).