DC 7-24V 200W Type A
A strong reminder:
The supporting voltage range of this electrical regulation is DC 7-24V, 24V is the limit voltage, the switching power supply can supply power, but cannot connect 24V battery, 24V battery full voltage is close to 29V! Wrong connection burns up at your own risk!
Product parameters:
Product Name: Single button (potentiometer) three-phase DC brushless Hallless drive
Model: X30B (single button) X30A (potentiometer)
Working voltage: 6.5-24V
Drive current: rated 12A plus fan cold 20A
Maximum speed: 224000 RPM (2-pole motor), 74000 RPM (6-pole motor), 40000 RPM (12-pole motor), 35000RPM (14-pole motor).
Product size: length 45MM* width 26MM* height 12MM (without wire and protruding capacitor)
Weight: X30A 29g X30B 27g about
Features:
ESC is specially designed for all kinds of industrial control electric tools such as air pump, water pump, oil pump and fan which use DC three-phase brushless motor. The default medium angle and long time high current work, Jianyi plus fan cold has overheat protection When the external heat dissipation condition of the ESC is poor, the temperature is automatically reduced when the temperature exceeds 100 degrees, and the temperature drops to 100 degrees to return to normal.
Precautions:
1. The power supply circuit on the main board has no fuse, and the built-in self-addition will cause the chip on the board to be permanently damaged (even if it is 1 second).
2. There is motor stall protection during normal operation. Since the module power and current are very large, please do not artificially short circuit when the module is not working normally. Once the short circuit has the possibility of burning the line, please use the first wiring test machine. Current low voltage test, after ok, then work with high current and high voltage
Potentiometer section instructions:
The standard speed control of the potentiometer does not require an external control signal. It increases clockwise and decreases counterclockwise.
Also applicable to external PLC 0-5 analog quantity control Unplug the potentiometer cable, external 0-5 analog quantity control signal and ground line, respectively connected with the brushless driver board input signal end, as long as the two lines are OK
DC 7-24V 200W Type B
Features:
1. It works when powered on, no external signal is required, and the button model realizes acceleration and deceleration through a single button
2. DC three-phase brushless without Hall control board, the motor can work normally without Hall
3. The single-button model supports single-button free switching of acceleration and deceleration, with power-off memory function
4. BLDC wide voltage 7-24V high power small volume high power
5. Specially developed and designed for various industrial control electric tools such as air pumps, water pumps, oil pumps, fans and so on that use DC three-phase brushless motors
1. It works when powered on, no external signal is required, and the button model realizes acceleration and deceleration through a single button
2. DC three-phase brushless without Hall control board, the motor can work normally without Hall
3. The single-button model supports single-button free switching of acceleration and deceleration, with power-off memory function
4. BLDC wide voltage 7-24V high power small volume high power
5. Specially developed and designed for various industrial control electric tools such as air pumps, water pumps, oil pumps, fans and so on that use DC three-phase brushless motors
Instructions for single-button models:
The button ESC is different from the model aircraft ESC. After the ESC is powered on, the motor will rotate directly without the need for an external speed control signal. The motor speed can be adjusted through the buttons on the ESC. Jog the button, step by step acceleration (deceleration) Press the button still, the motor speed will always increase (decrease), after the increase to the maximum, the speed will not change, release the button and press the button again, the motor speed It will gradually decrease again. When the speed is reduced to 0, the motor stops. Release the button and press the button again, and the speed will gradually increase. In this way, under the action of the button, the motor speed will cycle from small to large, and then from large to small (the time from 0 to the largest is about 10 seconds). When the button is released for 3 seconds, the set speed will be automatically saved in the ESC. After the power is turned off and the power is restarted next time, it will rotate at the last set speed. Deceleration (acceleration) At this time, just click the button twice quickly to reverse the direction of acceleration (deceleration).
There is an LED indicator light on the main board, the light is on for acceleration mode, and the light is off for deceleration mode
The button ESC is different from the model aircraft ESC. After the ESC is powered on, the motor will rotate directly without the need for an external speed control signal. The motor speed can be adjusted through the buttons on the ESC. Jog the button, step by step acceleration (deceleration) Press the button still, the motor speed will always increase (decrease), after the increase to the maximum, the speed will not change, release the button and press the button again, the motor speed It will gradually decrease again. When the speed is reduced to 0, the motor stops. Release the button and press the button again, and the speed will gradually increase. In this way, under the action of the button, the motor speed will cycle from small to large, and then from large to small (the time from 0 to the largest is about 10 seconds). When the button is released for 3 seconds, the set speed will be automatically saved in the ESC. After the power is turned off and the power is restarted next time, it will rotate at the last set speed. Deceleration (acceleration) At this time, just click the button twice quickly to reverse the direction of acceleration (deceleration).
There is an LED indicator light on the main board, the light is on for acceleration mode, and the light is off for deceleration mode
Product parameters:
Product name: single button (potentiometer) three-phase DC brushless without Hall drive
Working voltage: 6-20V (limit 24V) suitable for 2-5S lithium battery
Driving current: rated 16A plus fan cooling 25-30A
Maximum speed: 224000 RPM (2-pole motor), 74000 RPM (6-pole motor), 40000 RPM (12-pole motor), 35000 RPM (14-pole motor).
Features: The ESC is specially developed and designed for all kinds of industrial control power tools such as air pumps, water pumps, oil pumps, fans and so on that use DC three-phase brushless motors. , when the external heat dissipation condition of the ESC is poor and the temperature exceeds the upper limit of 100 degrees, the power will be automatically reduced, and the temperature will return to normal when the temperature drops to the lower limit of 90 degrees.
Product name: single button (potentiometer) three-phase DC brushless without Hall drive
Working voltage: 6-20V (limit 24V) suitable for 2-5S lithium battery
Driving current: rated 16A plus fan cooling 25-30A
Maximum speed: 224000 RPM (2-pole motor), 74000 RPM (6-pole motor), 40000 RPM (12-pole motor), 35000 RPM (14-pole motor).
Features: The ESC is specially developed and designed for all kinds of industrial control power tools such as air pumps, water pumps, oil pumps, fans and so on that use DC three-phase brushless motors. , when the external heat dissipation condition of the ESC is poor and the temperature exceeds the upper limit of 100 degrees, the power will be automatically reduced, and the temperature will return to normal when the temperature drops to the lower limit of 90 degrees.
Precautions:
1. There is no fuse in the power supply circuit on the motherboard. Jianyi has added it by himself. The reverse connection of the positive and negative poles of the power supply will cause permanent damage to some chips on the board (even in a short period of time, there is a risk of damage)
2. There is motor stall protection during normal operation. Since the power and current of the module are very large, please do not artificially short-circuit the module when the module is not working normally. Once the short-circuit is short-circuited, it may burn the line and burst the tube. Please use a small one for the first wiring test. Current low voltage test, after ok, then pass high current and high voltage to work
3. Do not connect the motor that obviously does not match the voltage, current and power of the drive module or is far away from the motor to avoid inexplicable damage.
1. There is no fuse in the power supply circuit on the motherboard. Jianyi has added it by himself. The reverse connection of the positive and negative poles of the power supply will cause permanent damage to some chips on the board (even in a short period of time, there is a risk of damage)
2. There is motor stall protection during normal operation. Since the power and current of the module are very large, please do not artificially short-circuit the module when the module is not working normally. Once the short-circuit is short-circuited, it may burn the line and burst the tube. Please use a small one for the first wiring test. Current low voltage test, after ok, then pass high current and high voltage to work
3. Do not connect the motor that obviously does not match the voltage, current and power of the drive module or is far away from the motor to avoid inexplicable damage.
packing list:
Motor governor x1
Motor governor x1
DC 6-24V 1000W
Motherboard specifications:
Working voltage: 6-20V (limit 24V)
Drive current: rated 30A plus air cooling 50A
Maximum power: 1000W
Overcurrent protection: Yes
Locked-rotor protection: Yes (after locked-rotor, the current will automatically drop and run at intervals)
Over-temperature protection: Yes (over-temperature power is halved)
Maximum speed: 224000 RPM (2 pole motor), 74000 RPM (6 pole motor), 40000 RPM (12 pole motor), 35000 RPM (14 pole motor).
Precautions:
Reverse connection of the positive and negative poles of the power supply on the motherboard will cause permanent damage to some of the chips on the board (large current will not work for a few seconds)
There is sampling over-current protection at the output of the motor during normal operation. Because the power and current of the module are very large, please do not artificially short-circuit the module when the module is not working normally. Once the short-circuit, the circuit may be burnt and the tube may burst, the first wiring test machine Please use small current and low voltage test, after ok, then apply high current and high voltage. Because it is a bare board module, please pay attention to the insulation of the wiring head. It is strictly forbidden that strong voltage touches the board parts.
Do not connect the motor that is obviously inconsistent with the drive module voltage, current, or power, to avoid inexplicable damage
Package Included:
Motor drive boardx1
Am 09.09.2023 hat der Verkäufer die folgenden Angaben hinzugefügt: