Features:
* Aluminum alloy material Full CNC processing .
* Easy RC model aircraft accessory,easya and convenient to install and use.
* RC Aircraft Replacement. Nice replacements for your old or broken parts.
* High Accuracy: using dynamic and static calibration, accuracy is higher, debugging is simple,farewell to the tedious zero test during
* Usage method :1. Wing installation ; 2. Aircraft top installation
Install Pitot Tube:
DIY Pitot Tube: You can do it with 2 refills. The dynamic tube is straight-through, installed outside the machine; the static tube plugs the tube, and then open 4 small holes on the side, about 0.5-1mm. When you install the airspeed sensor on the plane, use this pitot kit. The kit includes two tubes, a static tube (the port is sealed with a small hole on one side) and a dynamic tube (straight tube, not sealed). The two tubes can be placed side by side. On EasyStar, you need to pass them through the foam in front of the cockpit so they can be exposed to the airflow. Make sure the hole on the side of the tube is not covered. They should extend at least 1 cm from the nose. First connect the silicone tube behind the pitot tube to the air pressure sensor. The silicone tube from the straight tube should be connected to the upper port, and the curved tube to the lower port. Drill or cut a small hole in the foam and push the pitot tube forward.
Note: If your aircraft has a propeller in front of it, the dynamic tube must be pressed on a wing, or at least under the fuselage, to avoid propeller airflow. The static tube can be installed anywhere.
Check Operation:
You can use APM Planner or other ground stations to read the airspeed count value. Blow into the pitot tube and observe the response. Zero and small oscillations (2-3) in normal air are normal. The airspeed varies with the square root of the pressure, so the change at near zero pressure difference is very small, and a greater pressure change is required to produce the estimated speed change during flight. If you see mostly 0, 1, 2, and occasionally bounce to 3 or 4, think it is normal. You will not see such changes while flying.
Package List:
1 x Airspeed Tube
Note: Not included Airspeed Sensor.
* Aluminum alloy material Full CNC processing .
* Easy RC model aircraft accessory,easya and convenient to install and use.
* RC Aircraft Replacement. Nice replacements for your old or broken parts.
* High Accuracy: using dynamic and static calibration, accuracy is higher, debugging is simple,farewell to the tedious zero test during
* Usage method :1. Wing installation ; 2. Aircraft top installation
Install Pitot Tube:
DIY Pitot Tube: You can do it with 2 refills. The dynamic tube is straight-through, installed outside the machine; the static tube plugs the tube, and then open 4 small holes on the side, about 0.5-1mm. When you install the airspeed sensor on the plane, use this pitot kit. The kit includes two tubes, a static tube (the port is sealed with a small hole on one side) and a dynamic tube (straight tube, not sealed). The two tubes can be placed side by side. On EasyStar, you need to pass them through the foam in front of the cockpit so they can be exposed to the airflow. Make sure the hole on the side of the tube is not covered. They should extend at least 1 cm from the nose. First connect the silicone tube behind the pitot tube to the air pressure sensor. The silicone tube from the straight tube should be connected to the upper port, and the curved tube to the lower port. Drill or cut a small hole in the foam and push the pitot tube forward.
Note: If your aircraft has a propeller in front of it, the dynamic tube must be pressed on a wing, or at least under the fuselage, to avoid propeller airflow. The static tube can be installed anywhere.
Check Operation:
You can use APM Planner or other ground stations to read the airspeed count value. Blow into the pitot tube and observe the response. Zero and small oscillations (2-3) in normal air are normal. The airspeed varies with the square root of the pressure, so the change at near zero pressure difference is very small, and a greater pressure change is required to produce the estimated speed change during flight. If you see mostly 0, 1, 2, and occasionally bounce to 3 or 4, think it is normal. You will not see such changes while flying.
Package List:
1 x Airspeed Tube
Note: Not included Airspeed Sensor.
