DC 50V-3700V
Features:
1.At the same time can test the insulation voltage of the object. Such as switches, buttons, connectors between the two legs of the insulation voltage test.
2. Compact product
3. Convenient to carry and store
4. It is also very convenient to test the insulation between windings, such as motor, industrial frequency transformer, high frequency transformer, phase-to-phase insulation, insulation measurement of the shell core.
5. Wide range of applications can be measured: NIMOS / PMOS / IGBT / transistor / unidirectional SCR / voltage regulator diode / light-emitting diode / rectifier bridge / varistor / ceramic gas discharge tubes / electrolytic capacitors / the value of the withstand voltage.
Parameters:
Adjustable output voltage: DC 50V-3700V
Voltage display accuracy: 0.3%
Output voltage error: ±50V, resistance has error actual output 3650-3750V
Adjustable output current: 50uA-5mA
Output mode: constant voltage, constant current output
Maximum power of the whole machine: 5
Voltmeter resolution: 0.1V below 100V, 1V above 100V
Battery capacity: 700mA lithium battery
Charging current :550mA
Charging interface :TYPE-C (charging red light, full green light)
Charging adapter: 5V1A mobile phone charger can be charged
Protection function: 80 over temperature protection (high temperature light blue)
Lithium battery undervoltage: battery below 3.3V amount of blue light
Machine size: 98*70*37
Host weight: 108g (without any accessories)
Package includes:
Tester *1
Instruction manual *1
Crocodile clips test line accessories *10
DC120-2700V
![](https://pg-cdn-a2.datacaciques.com/00/NDAy/24/03/11/fpp9p7331qe4g488/05de4f292e94a58f.jpg)
Features:
1. The output voltage is 110~2600V DC, you can turn the voltage adjusting button clockwise to make the voltage bigger, and counterclockwise to make the voltage smaller.
2. The output current is 0.25~3.4mAh, you can turn the voltage adjusting button clockwise to make the current bigger, and turn counterclockwise to make the current smaller.
3. When testing MOS tubes, transistors and Zener diodes, it is recommended to adjust the current to the minimum size of 0.25mA. When testing LED backlight boards, it is recommended to adjust the current to a maximum size of 3.4mAh.
4.Portable size: the small size of this tool is very convenient for daily use, you can carry it in your tool bag without taking up too much storage space.
5.Built-in 600 mAh high-capacity lithium battery power supply, which can be charged in time through the Type-C port.
6.Wide range of applications: the tool can be widely used for MOS, triode, IGBT, diode, Zener diode, diode bridge maximum voltage capacity test, capacitor and varistor voltage verification, LED backlighting and light board test, etc.
Product Parameters:
Battery capacity: 3.7V 600mAH
Charging port: TYPE-C
Input: 5V 1A
Charging current: Max.550mA
Output voltage: 120-2700V
Output Current: 0.2-3.8mA
Applicable components: MOS tube/IGBT/transistor/diode/electrolytic capacitor/LED/MOV/one-way thyristor/rectifier bridge
Test Objective: Breakdown voltage value of electronic components
Attention:
1. Don't use it to test high voltage large electrolytic capacitors such as 450V/220UF. It is OK to test low voltage capacitors such as 2200UF/35V.
2. If there is no output voltage when pressing the red high-voltage start button, it is likely that the voltage of the lithium battery is lower than 3.1V, which can't energise the tester, and it needs to be charged in time.
3. Only when testing LEDs and voltage regulator diodes, the output current can be adjusted to the maximum value, for testing other parts, the output current can be adjusted to the minimum value to avoid damaging the parts.
Package and list:
Standard version: host * 1 + manual * 1 + meter pen * 1
Advanced version: host *1 + manual *1 + pen *1 + LCR test clip *1