Adrifil Universal Nano Hybrid Light Cure Composite
Universal Shades : A1, A2, A3, B2
Adrifil Bond V Total-Etch Adhesive 5ml
Adrifil Etch Dental Etching Gel 2.5ml
flowable
Descriptions
Adrifil Universal Nano Hybrid Light Cure Composite
is a light curable radiopaque composite. It can be used for anterior and
posterior dentine and enamel restorative treatment. The inorganic filler loading is about 71 % by
volume. The particle size varies from 0.03 to 5 microns.
PACKAGES : Refill : 4g syringe
Shade: Corresponding VITA shades
Universal Shades : A1, A2, A3, B2
COMPOSITION: BisGMA, barium glass, nano-silica, photoinitiator, stabilizer.
APPEARANCE: High viscous paste
Adrifil Bond V Total-Etch Adhesive is 5th generation universal adhesive. Adrifil Bond V is a single
bottle adhesive consisted of methyl methacrylate monomers and solvent. It demonstrates a
great adhesion to dentin and enamel. It is easy to use adhesive with multifunctions.
PACKAGES: 5 ml bottle
COMPOSITION: BisGMA, photoinitiator, stablizer, acetone and other additives
APPEARANCE: Light yellow liquid
Adrifil Etch Dental Etching Gel is a polymer-thickened phosphoric acid formulation intended
for use on enamel and dentin. This ETCHANT will effectively remove the smear layer, etchand demineralize enamel and dentin, producing the necessary micro retentive surface for successful bonding. The polymer thickener creates thixotropic properties, enhancing handling characteristics. The etchant rinses away cleanly and quickly, leaving no residue.
PACKAGES: 2.5 ml per syringe
COMPOSITION: Water, phosphoric acid and other additives
APPEARANCE: Blue Semi-Gel.
FUNCTION:
Adrifil Universal Nano Hybrid Light Cure Composite
After filling, a blue light initiates a quick free radical polymerization generating an organic
resin and inorganic filler composite which demonstrates a great strength and aesthetic
appearance as real tooth. Due to its high radiopacity, a clear X-ray picture will be helpful for
clinic practice.
Adrifil Bond V Total-Etch Adhesive
Due to s unique chemical composition, and its minimal and uniform film thickness, this
system could be applied to direct and indirect restoratives. Its good flowability, great
wettability and permeability significantly improve bonding strength. In clinic practice, this
adhesive will be applied on dentin or enamel surface following a light cure after evaporating
solvent.
Adrifil Etch Dental Etching Gel
The polymer thickener creates thixotropic properties, enhancing handling characteristics.
The etchant rinses away cleanly and quickly, leaving no residue.
INDICATIONS FOR USE:
Adrifil Bond V / Adrifil Universal Composite is Ideal for direct and indirect restoratives: Metal, Porcelain and Composite
Core build up, in-lay and on-lay
Veneer repairs, porcelain restoration, metal and non-metal bonding
Adrifil Etch Dental Etching Gel dentin and enamel
Cleaning agent on dental restorative material
Disclaimer :
The sale of this item may be subject to regulation by the U.S. Food and Drug Administration and state and local regulatory agencies. If so, do not bid on this item unless you are an authorized purchaser. If the item is subject to FDA regulation, I will verify your status as an authorized purchaser of this item before shipping of the item.
INSTRUCTIONS:
(1)Isolate tooth and then prepare the cavity in a conservative manner. Clean the entire
surface with a slurry of pumice and water.
(2)Apply etchant using a tip, a disposable syringe tip, or disposable brush tip. Allow etchant
to remain in place for 15 seconds. Etching time should be monitored with a stopwatch.
Begin timing at the end of application.
Option: Place etchant on enamel first, then proceed to cover dentin, for a slightly longer
enamel etching time.
(3)Rinse thoroughly (at least 5 seconds) to completely remove all traces of etchant.
(4)Drying: gently air dry until there is no visible water. Do not allow enamel or dentin to dry
for an excessive period of time.
(5)Applying Adrifil BOND V Self-Etching Light Cure Adhesive : dispense 1-2 drops of Adrifil Bond into
a mixing well, apply enough Adrifil Bond to the entire preparation with a little brush until a shiny
surface is achieved and then wait for 10 seconds (Adrifil should not be applied too much ). Use
a gentle stream of air to evaporate the solvent for 5 seconds. (If using a non self-etching
adhesive, an etching step should be used according to the manufacturer’s instruction).
(6)Cure: light cure for 20 seconds at more than 500mW/cm2. Keep the distance to exposure
surface less than 4 mm.
(7)Applying Adrifil Universal Nano Hybrid Light Cure Composite: place selected composite into cavity preparation
following by light cure. According to following table, the curing time is recommended for
different depth and color shades. In order to reduce shrinkage stress, for a large cavity, an
increment filling is recommended. In general, 1-2 mm increments are placed into cavity
preparation from different sides and the restoration is built incrementally. Each increment is
light cured for 30 seconds.
(8) Finishing: after light cure, adjust restoration.
(9) Polishing: use polishing strip or disc to polish the surface.
WARNING:
product with any material contained eugenol.
etchant is allowed to remain on the skin or mucosa for extended periods of time. If accidentally
splashed into the eye, flush with copious amounts of water and seek medical attention
immediately. In case of contact with other tissues, rinse immediately with plenty of water for
several minutes.
PRECAUTIONS:
contact, wash skin with soap and water. In severe situation, get medical attention.
this product. This product contains acetone which is flammable. Avoid flam.
Dispose of used or contaminated TIPS and syringe tips.Do not clean,disinfect or reuse.
PRECAUTIONS:
Keep away from direct sunlight. See individual component labels for specific expiration
dates. Store at 4- 25℃in a cool and dry place and avoid direct sun exposure.
Recap the bottle after use.
ATTENTION:
To an exposed pulp, a pulp capping material such as Calcium hydroxide may be used before using
this product.
STORAGE:
Store at 4-25℃ in a cool and dry place and avoid direct sun exposure. Recap the syringe after use.
DISPOSAL:
After the product is used up, dispose it as normal medical rubbish.
SHELF LIFE : 3 years.
STANDARD : IS0 4049: Dentistry-Polymer-based filling, restoration and luting materials