Reufrbished QY6-0042 Printhead for iX4000 iX5000 iP3100 iP3000 560i 850i MP700 MP710 MP730 MP740
Feature:
Excellent performance and high quality.
Made of high-quality material, durable, firm and stable for us to use.
This is a cleaned, thoroughly tested and sealed Printhead.
Good stability, long lifespan.
Full color function.
Product Condition : Original Refurbished Printhead ,95% New.
Warranty : One Year Free Warranty , Life-long Service.
OEM code: QY6-0042
Compatible Models:
Fit for QY6-0042 iX4000 iX5000 iP3100 iP3000 560i 850i MP700 MP710 MP730 MP740
Packing includes:
1 x print head
Note:
1.In print entered please turn off the power of the printer, or it will cause the mainboard chip burned.
After loading the print head, please don't install ribbon overhead 10 pieces of A4 document,
so that make the new needle have a running-in process, and then put the ribbon. I hope you can be careful operation.
2.If the original print head was broken and especially leaked ink, the mainboard has burned possibly,
so please troubleshoot the problem of the mainboard before replacing the print head. In addition,
the F1,F2 fuze wire of mainboard can only be replaced by the original fuze that has same current value and same model.
If replacing fuze that is biger current value and different model, Both printhead and mainboard are possible to be broken.
3.Print head requires lots of attention, It is easy to cause man-made damage if a non-professionals replace printhead blindly.
There is a regulation that printhead is not warranty, and it is delicate and expensive.
please do not make commissioning on the machine, and please treat it with caution.
4.If you are not familiar with the machine, it is recommended that you had better send the print head to a repair station
or find professionals to replace the nozzle, so as to avoid unnecessary losses and unnecessary trouble.
Before you install this product, you need to pay attention to:
1.After receiving the print head, if you use a needle tube to inject water to check the nozzle or see if it is blocked, this is a very redundant and dangerous behavior.If the printing effect is not clear, press the machine cleaning button (the pFirst of all, once the print head enters the water, if the water is not dry, it is powered on. The main board will be burned out, and the print head will be burnt out. Secondly, the print heads sold in our shop have been strictly tested and filled with protective liquid.If you use a needle to inject water into the print head, it will not only wash away the protective liquid in the head, but also easily cause air blockage in the print head, resulting in no ink.
2.Be careful when installing the print head, be sure to cut off the power first, and install it in place.
3.When connecting the plug cable, do not have ink on it, and make sure that it is in good contact with the socket.
4.The steel shaft should also be clean and smooth. You can use a paper towel to stick some lubricating oil to wipe it. Do not directly add oil to the shaft. The excess oil will flow to the print head and cause damage.
5.After the machinery and circuit are all correct, check the water circuit. Firstly, check whether the ink volume in the ink cartridge is sufficient; secondly, check whether the small cleaning blade and the ink suction pump are dirty.
6.There will be air in the newly installed print head, so it will not print normally immediately. The printer can only produce perfect results after the air in the head is completely discharged.You can use the machine's own cleaning function for intermittent cleaning(Clean 2 times each time, and then 2 times after 30 minutes) Repeated over-cleaning will cause ink accumulation in the cleaning pump, which will not only cause color mixing, ink leakage, and waste ink.Finally, you can print more pictures to let the print head exhaust air during work.
Deutsch
QY6-0042 Druckkopf für IX4000 IX5000 IP3100 IP3000 560i 850i MP700 MP710 MP730 MP740
Feature:
Hervorragende Leistung und hohe Qualität.
Hergestellt aus hochwertigem Material, langlebig, fest und stabil für uns.
Dies ist ein gereinigtes, gründlich getestetes und versiegelter Druckkopf.
Gute Stabilität, lange Lebensdauer.
Vollfarbfunktion.
Produktzustand: ursprünglicher renovierter Druckkopf, 95% neu.
Garantie: ein Jahr freie Garantie, lebenslanger Service.
OEM-Code: QY6-0042
Kompatible Modelle:
Fit für QY6-0042 IX4000 IX5000 IP3100 IP3000 560I 850i MP700 MP710 MP730 MP740
Verpackung beinhaltet:
1 x Druckkopf
Hinweis:
1. In eingegebener Druck, schalten Sie die Stromversorgung des Druckers aus, oder es wird dazu veranlasst, dass der Mainboard-Chip verbrannt wird.
Installieren Sie nach dem Laden des Druckkopfs bitte keine Ribbon-Overhead 10 A4-Dokumenten
Das macht also die neue Nadel einen laufenden Prozess und legen Sie dann das Farbband. Ich hoffe, dass Sie sorgfältiger Betrieb sein können.
2. Wenn der ursprüngliche Druckkopf gebrochen wurde und besonders durchgesickert wurde, hat sich das Mainboard möglicherweise verbrannt,
Bitte beheben Sie das Problem des Mainboards, bevor Sie den Druckkopf austauschen. In Ergänzung,
Der F1, F2 Fuzedraht von Mainboard kann nur durch den ursprünglichen Fuze ersetzt werden, der denselben aktuellen Wert und das gleiche Modell hat.
Beim Ersetzen von FUZE, das ein beließerer aktueller Wert und ein anderes Modell ist, sind sowohl der Druckkopf als auch das Hauptbord defekt.
3. Print-Kopf erfordert viel Aufmerksamkeit, es ist leicht, angemessene Beschädigungen zu verursachen, wenn ein Nicht-Fachmann den Druckkopf blind ersetzen.
Es gibt eine Regulierung, die der Druckkopf nicht garantie ist, und es ist empfindlich und teuer.
Bitte machen Sie keine Inbetriebnahme an der Maschine, und behandeln Sie es bitte mit Vorsicht.
4.Wenn Sie mit der Maschine nicht vertraut sind, wird empfohlen, den Druckkopf besser zu einer Reparaturstation zu senden
Oder finden Sie Fachleute, um die Düse zu ersetzen, um unnötige Verluste und unnötige Schwierigkeiten zu vermeiden.
Bevor Sie dieses Produkt installieren, müssen Sie darauf achten:
1. Wenn Sie den Druckkopf empfangen, wenn Sie ein Nadelröhre verwenden, um Wasser zu injizieren, um die Düse zu überprüfen oder zu sehen, ob er blockiert ist, ist dies ein sehr redundantes und gefährliches Verhalten. Wenn der Druckeffekt nicht klar ist, drücken Sie die Maschinenreinigungsknopf (der Pfirst aller, sobald der Druckkopf in das Wasser eintritt, wenn das Wasser nicht trocken ist, wird er angetrieben. Die Hauptplatine wird ausgebrannt, und der Druckkopf wird verbrannt. Zweitens werden die Druckköpfe in verkauft Unser Geschäft wurde streng getestet und mit Schutzflüssigkeit gefüllt. Wenn Sie eine Nadel verwenden, um Wasser in den Druckkopf zu injizieren, waschen Sie nicht nur die Schutzflüssigkeit in den Kopf, sondern verursachen auch leicht die Luftverblasung im Druckkopf, was er resultiert In keiner Tinte.
2. Beachten Sie, wenn Sie den Druckkopf installieren, sorgen Sie dafür, dass Sie die Stromversorgung zuerst abschneiden, und installieren Sie es an Ort und Stelle.
3. Wenn Sie das Steckkabel anschließen, haben Sie keine Tinte darauf, und stellen Sie sicher, dass es sich in gutem Kontakt mit der Steckdose befindet.
4.Die Stahlwelle sollte auch sauber und glatt sein. Sie können ein Papiertuch verwenden, um etwas Schmieröl zu kleben, um es abzulöschen. Fügen Sie nicht direkt Öl zur Welle hinzu. Das überschüssige Öl fließt zum Druckkopf und verursacht Beschädigungen.
5.Nach der Maschine und der Stromkreis sind alle korrekt, überprüfen Sie den Wasserkreislauf. Überprüfen Sie zunächst, ob das Tintenvolumen in der Tintenpatrone ausreichend ist; Zweitens prüfen Sie, ob die kleine Reinigungsklinge und die Tintensaugpumpe verschmutzt sind.
6. Es wird Luft im neu installierten Druckkopf sein, sodass er nicht sofort normal druckt. Der Drucker kann nur perfekte Ergebnisse erzeugen, nachdem die Luft im Kopf vollständig entlastet ist. Sie können die eigene Reinigungsfunktion der Maschine für die intermittierende Reinigung verwenden (2-mal sauber jedes Mal, und dann 2 mal nach 30 Minuten) wiederholte Überreinigung wird Tinte verursachen Akkumulation in der Reinigungspumpe, die nicht nur Farbmischungen, Tintenleckage und Abfalltinte verursacht, können Sie mehr Bilder drucken, um die Druckkopfabluft während der Arbeit zu lassen.