Ultrasonic Ranging Sensor Module Distance Measuring Detector US-100 US-015 US-016 US-025 US-026 CS100 Replace HC-SR04 HC SR04 HCSR04 For Arduino
US-100
Product parameters:
Product: US-100 Ultrasonic Ranging Module
Operating voltage: DC 2.4V~5.5V
Quiescent current: 2mA
Working temperature: -20~+70 degrees
Output method: level or UART (jumper cap selection)
Sensing angle: less than 15 degrees
Detection distance: 2cm-450cm
Detection accuracy: 0.3cm + 1%
Serial port configuration in UART mode: baud rate 9600, start bit,One stop bit, 8 data bits, no parity, no flow control.
US-015
Description:
US-015 ultrasonic ranging module class 2cm to 400cm non-contact ranging function, 5V power supply voltage, working current 2.2mA, support GPIO communication mode.
Features:
Working voltage: DC5V
Working current: 2.2mA
Working temperature: 0-70 Celsius
Output: GPIO
Induction Angle: < 15degrees
Detection range: 2cm to 400cm
Precision: 0.3cm+1%
US-016
Product Description:
Operating Voltage: DC 5V
Operating Current: 3.8mA
Operating temperature: 0 to + 70 degrees
Analog output voltage: (0 ~ Vcc)
Induction angle: less than 15 degrees
Detection range: 2cm-300cm
Detection accuracy: 0.3cm + 1%
Resolution: 1mm
US-025/US-026
-
US-025/US-026 is a high-performance, low-cost ultrasonic ranging module; the module uses a cost-effective ultrasonic ranging chip CS100; the ranging is up to 6 meters, the ranging accuracy is high; the measurement consistency is good, the measurement Stable and reliable.
-
The US-025/US-026 ultrasonic ranging module can realize non-contact ranging function of 2cm~6m, working voltage is 3V-5.5V, working current is 5.3mA, support GPIO communication mode, and work stably and reliably.
-
US-025 has the same performance as US-026, the same size and the same principle.
Difference:
-
US-025 uses a double panel, US-026 uses a single panel;
-
US-025's 4Pin pin header is soldered on the front side (the probe side), US-026 is a single panel, the front side (the probe side) has no pad, and the pad is soldered on the back side (chip side).
Technical Parameters:
Schematic:
Numbered 1, 2, 3, 4 from left to right. The definition is as follows:
1: Connect to VCC power supply (DC 3V-5.5V).
2: Connect the Trig terminal of the external circuit and input a high level above 10uS to this pin to trigger the module ranging.
3: Connect to the Echo end of the external circuit. When the distance measurement ends, this pin will output a high level, and the level width is the sum of the ultrasonic round trip time.
4: Connect to an external circuit ground.
CS100 Chip
CS100 is an industrial grade ultrasonic distance measuring chip. CS100 integrates ultrasonic transmitting circuit, ultrasonic receiving circuit and digital processing circuit. The single chip can complete ultrasonic ranging, and the ranging result is output by pulse width. The communication interface is compatible. Existing ultrasonic modules.
The CS100 works with a 40KHZ open-ended ultrasonic probe that requires only a 22MR pull-down resistor and an 8M crystal to achieve high-performance ranging.
Less device usage can significantly reduce board area and improve reliability. At the same time, fewer peripheral devices make wiring easier. In a cost-sensitive reference scenario, ultrasonic ranging can be achieved using a single-sided PCB. Significantly reduce costs.
CS100 is available in SOP16 package
Schematic:
HC-SR04 Bracket
