This Item includes:
1 stepper motor:
Technical Specifications
Part No.: WT57STH115-4204A Single Shaft
Frame Size: NEMA23
Step Angle: 1.8 degree
Voltage: 3.78VDC
Current: 4.2
Resistance: 0.9 Ohm/phase
Inductance: 3.8 mH/phase
Holding torque: 30
Rotor inertia: 810
Detent torque: 1.2
Number of wire leads: 4
Weight: 1.55KG
Length: 115
Front shaft diameter: 8mm
Front shaft length: 21mm round shaft
Blue B-
Attention:)
There is single flat shaft, dual flats shaft, round shaft, keyway shaft and screw thread shaft, 4 Leads, 6Leads and 8 Leads in different stepper motor with different type.
Without informing, we'll send single shaft to you!
2.DQ542MA driver
Input voltage | 18-50VDC |
Input current | ＜ 4A |
Output current | 1.0A～4.2A |
Consumption | Consumption：80W； Internal Insurance：6A |
Temperature | Working Temperature -10～45℃； Stocking temperature -40℃～70℃ |
Humidity | No condensation, no water droplets |
gas | Prohibition of combustible gases and conductive dust |
weight | 300GS |
Index Type | S-350-5 | S-350-7.5 | S-350-12 | S-350-15 | S-350-24 | S-350-27 | S-350-48 |
DC Voltage | 5V | 7.5V | 12V | 15V | 24V | 27V | 48V |
Voltage Tolerance | ± 2% | ± 2% | ± 1% | ± 1% | ± 1% | ± 1% | ± 1% |
Rated Current | 50A | 40A | 29A | 23A | 14.6A | 13A | 7.3A |
Current Range | 0-50A | 0-40A | 0-29A | 0-23A | 0-14.6A | 0-13A | 0-7.3A |
Ripple&Noise(Max.) | 150mVp-p | 150mVp-p | 150mVp-p | 150mVp-p | 150mVp-p | 200mVp-p | 240mVp-p |
Line Regulation | ± 0.5% | ± 0.5% | ± 0.5% | ± 0.5% | ± 0.5% | ± 0.5% | ± 0.5% |
Load Regulation | ± 1% | ± 1% | ± 0.5% | ± 0.5% | ± 0.5% | ± 0.5% | ± 0.5% |
Rated Power | 250W | 300W | 348W | 348W | 350.4W | 351W | 350.4W |
Rated Power | 74% | 79% | 74% | 78% | 83% | 83% | 84% |
Voltage Adjust Range | 4.5-5.6V | 6-9V | 10-13.2V | 13.5-18V | 20-26.4V | 26-32V | 41-56V |
Voltage Range | 90~132VAC/180-264VAC 47~63Hz;255~370VDC | ||||||
AC Current | 4.5A/115V 2.5A/230V | ||||||
Inrush Current(Max.) | 25A/115V 50A/230V | ||||||
Leakage Current | <3.5mA/240VAC | ||||||
Overload Protection | 105-145% TYPE：OUTPUT CUTOUT AC Restart | ||||||
Over-voltage Protection | 115%-135% | ||||||
Over-temperature Protection | RTH3≥50℃ FAN ON≤45℃ FAN OFF, ≥80℃ OUTPUT CUTOUT(5-15V) | ||||||
Temp.Coefficient | ± 0.03%/℃(0~50℃) | ||||||
Setup.Rise,Hold Time | 200ms,100ms,20ms | ||||||
Vibration | 10~500Hz,2G 10min,/11cycle,60min,each axes | ||||||
Withstand Voltage | I/P-O/P:3KVACI/P-FG:1.5KVACI/P-FG:0.5KVAC | ||||||
Isolated Resistor | I/P-O/P,I/P-FG,I/P-FG:500VDC/100MΩ | ||||||
Working Temp.Humidity | -10℃~+50℃,20%~90RH | ||||||
Storage Temp.Humidity | -20℃~+85℃,10%~95%RH | ||||||
Dimension | 215¡Á115¡Á50mm | ||||||
Weight | 0.9kg | ||||||
Safety Standards | UL1950 | ||||||
4. breakout board: DB25:
Description
Built in DB25 male connector.
DB25 output pin:P1,P2,P3,P4,P5,P6,P7,P8,P9,P14,P16,P17
DB25 input pin:P10,P11,P12,P13,P15.
DB25 GND pin:P18-P25.
Power supply:+5VDC
Built in C-class optical-coupler.
High quality with surface-mount Tech.
It can connection 6 drivers and control 6 motors in the same time.
Built in DB25 male connector.
DB25 output pin:P1,P2,P3,P4,P5,P6,P7,P8,P9,P14,P16,P17
DB25 input pin:P10,P11,P12,P13,P15.
DB25 GND pin:P18-P25.
Power voltage is 5VDC and support with MACH3 ect.software
Built in optical-coupler.
You can set these pins according to software as follows:
Output pins:P1,P2,P3,P4,P5,P6,P7,P8,P9,P14,P16,P17
P2-X axis Pulse,P3-X axis Direction;
P4-Y axis Pulse,P5-Y axis Direction;
P6-Z axis Pulse,P7-Z axis Direction;
P8-A axis Pulse,P9-A axis Direction;
P14-B axis Pulse,P1-B axis Direction;
P16-C axis Pulse,P17-C axis Direction;
Input pins:P10,P11,P12,P13,P15
Set them for Emergency Stop and X Y Z Limit switch
Note :)
More order quantities, more discount!!!
Shipping
1) Normally,Your item(s) will be shipped within 24~48 hours after your payment is cleared.
2)For US and EU buyer: We have US and Germany warehouse, so we can ship goods to you from US or Germany if it is in the stock,but if it is out of stock, we will ship goods to you from China :)
3) There is online tracking number after the item shipped.
Problem and Feedback
1) Please give us the opportunity to resolve any problem when you have, we will try our best to help you.
2) Your satisfaction is of the utmost importance for us, so please contact us before you want to leave a negative feedback.
Refund
1) If you are not satisfied with the package, please tell us the reason.
2) Delivery cost must be paid by the buyer.
Honor
1) Changzhou Wantai Electrical Appliance Co.,Ltd has powerful technology, mature technics and complete testing equipment.
2) We have obtained ISO9001:2000 certification, CE certification and all of our products conform to EU RoSH requirements.
Note:
we can manufacture products according to our customer's requirements.
Application
Our products are mainly used in robotization, Spinning Automatization, Printing, Packing, Medica Machine, Make-up Equipment, Household Appliance, Milling Machine, Engraver Machine, CNC Routers and so on, automatic equipment of various trades. Recently, our motors are hot selling in 3D printer field :)
FAQ:
Q: How to connect the goods after purchasing?
A: We can send the Wiring Diagram to your email if you need :)
Q: What can I do if your motor don’t work well ?
A: All our goods are in high quality and 100% tested before selling. If it does not work well or with some problem,please check the wiring connection, and you can email to me for any question, we will try our best to help you :)
Q: How can I get some discount?
A: More order more discount :)
Q: How to be to your distributor ?
A.Welcome to be our distributor, please email to me :)
we will give our distributor competitive price & perfect technical support for mutually benefits!