Christmas Heart-shaped LED Flashing Light Circuit DIY Kit Electronic 48MM * 51MM
1. Suite Features
XSD-18 Cycle Lamp is a kind of lamp which with great appearance of streamlines and color appearance. 18 pieces of Tri-color LED in this suite are divided into three groups and formed a heart-shaped pattern. The transistor oscillates the drive of circuit and let the Tri-color heart-shaped pattern roll in a clockwise direction and start light. The light looks more colorful and dynamic, especially when used at night. It's the best choice for the festive gift.
PCB board Dimensions: 48MM * 51MM
2. Principle of Circuits
As it shown on below diagram, 18 pieces of LED have been divided into three groups: D1-D6,D7-D12 and D13-D18. All the three transistors try to breakover when the power is on. But only one of them could breakover at the first place due to the difference of the components. If the Q1 goes to breakover firstly, the D1-D6 will start light. As it shown on below diagram, 18 pieces of LED have been divided into three groups: D1-D6,D7-D12 and D13-D18. All the three transistors try to breakover when the power is on. But only one of them could breakover at the first place due to the difference of the components. If the Q1 goes to breakover firstly, the D1-D6 will start light. Because the collector voltage will be reduced which let the left side of C1 reduced to about 0V when the Q1 is on. As it cannot have a sudden change on the voltage of two ends of the capacitance, the base of Q2 has been reduced to 0V too. Then the Q2 is off and the D7-D12 turn off. But at this time, the high voltage of Q2 goes through C2 which make the voltage of Q3 base increased and let the Q3 on immediately. Then the D13-18 turn on. The collectors of both Q1 and Q3 are with low voltage during this period. And the D1-D6 and D13-D18 turn on, while D7-D12 turn off. But the collector voltage will be increased gradually after C1 has been charged by the power via R3. When the voltage is over 0.7V, Q2 enters a conducting state. And the collector voltage will increase which let the D13-D18 turn off. The circuit will operate according to this cycle that the 18 pieces of LED will be turned on by turns and 2 groups will be turned on at the same time.
Note:
The position of the LEDs is adjustable. But the LEDs with the same color should be put in the same group in parallel.
The flash frequency will be changed according to the capacitance.
3. Circuit Diagram
4.List of Components
Item Oder |
Item Name |
Specifications |
Code |
Item Oder |
Item Name |
Specifications |
Code |
01 |
Resistor |
10K |
R1 R3 R5 |
08 |
LED |
5MM Green to Green |
D13----D18 |
02 |
Resistor |
560R |
R2(Red LED) |
09 |
Transistor |
9014 |
Q1 Q2 Q3 |
03 |
Resistor |
220R |
R4(Yellow LED) |
10 |
Cable Terminal |
XH2.54 2P (Horizontal) |
J1 |
04 |
Resistor |
47R |
R6(Green LED) |
11 |
Power Wire |
2P 15MM |
1 |
05 |
Resistor |
22uF/25V |
C1 C2 C3 |
12 |
PCB |
5.1MM*4.8MM |
1 |
06 |
LED |
5MM Red to Red |
D1----D6 |
13 |
Battery Case |
2×AA |
1 |
07 |
LED |
5MM Yellow to Yellow |
D7----D12 |
14 |
|
|
1. We accept PAYPAL only.
2. Payment must be made within 7 days of auction closing (Unpaid dispute will automatically open when item
is not paid in 7 days).
3. PLEASE NOTE: SHIPPING&HANDING DOES NOT INCLUDE DUTIES, LOCATL TAXES OR ANY OTHER IMPORTATION FEES.
4. Please list your special requests (color, packages, value of declaration, etc.) in the EBAY NOTES SECTION
when you make payment
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is
very important to us. We request that you keep in touch with us immediately BEFORE you give us neutral or
negative feedback, so that we can satisfactorily address your concerns.It is impossible to address
issues if we do not know about them!