DEVILBISS PRO Lite Gravity Feed Spraygun
The NEW re-branded DeVilbiss PRO Lite Gravity Feed Spraygun
Fluid Tip
1.3mm
Air Cap
TE20
Contents
Devilbiss PROLite Gravity Feed Spray Gun, TE20, 1.3mm
560ml cup
Spanner
Cleaning brush
Colour identification rings
Instructional CD
Description
A lightweight Devilbiss spray gun developed for busy professional painters needing the ultimate in quality finishes.
Range of four advanced technology air caps (one HVLP and three High Efficiency) for optimum application performance with the latest solvent and waterborne coatings.
Ergonomic gun body design with even better fit and balance for comfort and control.
Three high efficiency fluid tips provide superb versatility across a range of climatic conditions and viscosities.
Coaxial, low kick air valve design gives smoother feel for even greater air and paintcontrol for ease of fade-outs and blend-ins.
The forged aluminium body is finished in a heavy duty anodised Blue.
The colour coding identification rings enable the individual painter to rapidly identify gun set ups specifically for basecoats, solid colours, clears, pearls and effects.
Technical Information
Cup Capacity - 560 mls
Weight (gun only) - 446 gms
Weight (gun & cup) - 629 gms
Air Cap - Plated Brass
Air Cap Retaining Ring - Clear Anodised aluminium
Fluid Tips - Stainless Steel
Fluid Needle - Stainless Steel
Air Inlet Thread - 1/4” Universal
Air Cap Comparisons
Aircaps for Clear and Base in Comparison
A common question: What is the difference between the TE10, TE20, T110 & HV30 air caps of the PROLite spray gun.
Below is an overview (from our point of view and after several discussions with painters)
Air Cap TE10 – basecoat & all rounder
Application: Standard water and solvent base basecoats, Air dry and MS clearcoats
Comments: Slower than TE20
Air Cap TE20 – clearcoat with faster flow
Application: Clearcoats (especially HS and UHS clearcoats) Recommended for polyurethane clear coats (in combination with 1.3mm nozzle)
Comments: Faster than TE10
In connection with 1.3mm nozzle widely recommended for 2K gloss / clearcoat
Air Cap HV30 – maximum transfer efficiency
Application: water base basecoat and clear coat
Air Cap T110 – clear coats with higher solids
Application: clearcoats (with higher solids)
Performance: Spray Pattern: 260-290 mm (10-11″)
Comments: Glass finishing
The most “forgiving” air cap
What are the recommended air pressures for the air caps?
The air pressure depends on different factors, e.g. the fluid to be sprayed or whether the fluid control is full open or not. A good starting point are following pressure settings:
Air Cap: HV30
Air Cap: Type HVLP
Part Number: 905238
Air Consumption (L/Min): 440 [15.5 cfm]
Recommended Air Inlet Pressure: 1.65 Bar [24 psi]
Typical Fan Pattern Size: 290-315mm
Air Cap: T110
Air Cap Type: High Efficiency
Part Number: 905245
Air Consumption (L/Min): 265 [9.4 cfm]
Recommended Air Inlet Pressure: 2.0 Bar [29 psi]
Typical Fan Pattern Size: 285-300mm
Air Cap: TE10
Air Cap Type: High Efficiency
Part Number: 905240
Air Consumption (L/Min): 270 [9.5 cfm]
Recommended Air Inlet Pressure: 2.0 Bar [29 psi]
Typical Fan Pattern Size: 285-300mm
Air Cap: TE20
Air Cap Type: High Efficiency
Part Number: 905241
Air Consumption (L/Min): 340 [12.0 cfm]
Recommended Air Inlet Pressure: 2.0 Bar [29 psi]
Typical Fan Pattern Size: 275-290mm