Purpose-designed, low-noise discrete Class-A amplifiers are implemented throughout the signal path for both MM and MC cartridges. The passive RIAA filter utilizes exceptional low-tolerance componentry, selectable capacitance for the MM input, and a selectable 18dB / octave Rumble Filter with a corner frequency at 11.4Hz.
“A simply stunning phono stage. My new reference in the mastering room.” — PETE LYMAN, MASTERING ENGINEERRegardless of whether you are listening to pristine classical recordings or the heaviest rock, getting the most out of your turntable system can be a challenge. The Precision Phono Pre-Amplifier is designed to coax out every detail from your pressings and turntable and provide your amplifiers with a complete and unadulterated signal, so you get the most from your vinyl collection.
Both the moving magnet and moving coil gain settings have been optimized to enhance the performance of the cartridge. These Phono stages use carefully-implemented discrete Class-A designs that utilize the highest performance JFETs and BJTs, honed over countless hours of listening and comparison.
THE SPECIFICATIONSThe resulting sound quality is technically - and musically - exceptional. The RIAA curve is matched to better than 0.15dB, and frequency response from 20Hz to 20kHz is better than +/-0.1dB. Even at 10Hz and 120kHz, there is less than a single decibel of deviation. Dynamic range is a powerful 101.58dB (MM path), and EIN is an exceptionally low -129dBV (MC path).
Beyond its technical feats however, it is the immersive listening experience that sets the Precision Phono Pre-Amplifier apart. The soundstage brings out a stunning three-dimensionality from recordings with a combination of a rich low end, pristine clarity throughout the crucial midrange, and a delicately sweet high-end. These are hallmarks of Rupert Neve’s vintage and modern recording equipment, and are exemplified in the Precision Series.
CONTROL YOUR TONEWhile the Fidelice Precision Phono Pre-Amplifier has an intentionally minimal feature set, there are several options that can adapt the phono stage to your system.
The left-hand switch inserts an 18dB / octave Rumble Filter with a corner frequency at 11.4Hz to remove extremely low-frequency artifacts from the signal, saving your amplifiers and speakers from exerting extra energy in replicating unnecessary sounds below that frequency.
Both moving magnet (MM) and moving coil (MC) signal paths are included such that the Precision Phono Pre-Amplifier can be used with virtually any cartridge. The MM setting provides an input impedance of 47kOhms, selectable capacitance at 110pF or 220pF to serve a variety of MM cartridges, and 40dB of gain. The MC setting provides an input impedance of 100 Ohms, capacitance of 220pF, and gain of 60dB.
Analog Inputs: Stereo RCA (MM), Stereo RCA (MC)
Analog Outputs: Stereo RCA (Line Output)
< +/-0.15dB from 20 Hz to 31.5 kHz
FREQUENCY RESPONSE< -0.2dB @ 10 Hz
< -1dB @ 120 kHz
< 0.1dB from 10 Hz to 22 kHz
POWER CONSUMPTION2.04W (24V, 0.085A)
MAXIMUM OUTPUT LEVEL17.6 dBV, 19.86 dBu, 7.62 Vrms
MOVING MAGNET(Source Z = 20 Ω Unbalanced, BW: 22Hz - 22kHz)
Input Impedance: 47 kΩ, 110 pF / 220 pF
Gain: 40 dB @ 1 kHz
Noise: -82 dBV
Equivalent Input Noise: -122 dBV
Signal-to-Noise Ratio: 77 dB
Dynamic Range: 99.6 dB
Crosstalk: -88 dB @ 10 kHz
THD+N (Input: 5mV RMS @ 1 kHz): 0.017%
(Source Z = 20 Ω Unbalanced, BW: 22Hz - 22kHz)
Input Impedance: 100 Ω, 220pF
Gain: 60 dB @ 1 kHz
Noise: -70 dBV
Equivalent Input Noise: -130 dBV
Signal-to-Noise Ratio: 64 dB
Dynamic Range: 87.6 dB
Crosstalk: -85 dB @ 10 kHz
THD+N (Input: 500μVRMS @ 1 kHz): 0.08%