Carrello di atterraggio in Carbonio per droni DJI Mavic Mini / Mini2
Finalmente un carrello che può essere montato sempre, senza limitazioni!
Appli-Bet propone un set di “estensioni” al carrello di atterraggio per
Mavic Mini e Mini2. Esso è composto da 4 pezzi separati che si innestano
ai quattro bracci del drone. La realizzazione con aste di Carbonio del
diametro di soli 2 mm risulta molto robusta e leggera e non influisce
sulla aerodinamica durante il volo del drone.
Il carrello innalza il drone di oltre 5 centimetri dal suolo permettendo
decollo e atterraggio da terreni erbosi o sassosi senza pericolo di
impatto con le eliche, specialmente le posteriori che sono molto
ravvicinate rispetto al suolo.
Le due aste anteriori si innestano a pressione alle punte del carrello
anteriore del drone. Le due aste posteriori si applicano ai due bracci
posteriori per mezzo di clip elastiche a scatto con cerniera con perno
in carbonio.
Sono disponibili sette versioni colore:
- Aste in carbonio nero con parti stampate in PETG nero lucido.
- Aste in carbonio nero con parti stampate in PETG arancio ad alta visibilità.
- Aste in carbonio nero con parti stampate in NYLON 6/66 neutro*.
- Aste in carbonio nero con parti stampate in NYLON 6/66 giallo fluo*.
- Aste in carbonio nero con parti stampate in NYLON 6/66 rosso*.
- Aste in carbonio nero con parti stampate in NYLON 6/66 verde*.
- Aste in carbonio nero con parti stampate in NYLON 6/66 blu*.
Montaggio:
Le due estensioni anterori dotate di un innesto a pressione
vanno inserite sulle punte dei bracci anteriori con le aste in carbonio
rivolte in avanti. Esercitare la pressione necessaria per ottenere un
serraggio sufficientemente solido per evitare il distacco durante il
volo.
Le due estensioni posteriori si applicano sui bracci posteriori a circa
un centimetro di distanza dai motori. Fare attenzione che le leve si
richiudano verso la direzione posteriore. Il corretto montaggio viene
raggiunto quando si nota un deciso “click” della chiusura. Per lo
smontaggio fare forza con l’unghia per sbloccare la leva di chiusura.
Prima di ripiegare i bracci del drone è necessario rimuovere le estensioni.
Dimensioni:
Anteriore mm h 57 mm
Posteriore mm h 75 mm
Innalzamento del drone da terra : 55 mm.
Peso del set di 4 pezzi:
7,9 grammi versione in PET nero e arancio.
7,2 grammi la versione in Nylon
-----------------------------------
Carbon landing gear for DJI Mavic Mini / Mini2 drones
ATTENTION: When ordering, please let us know if you wish to mount it on the Mavic Mini or Mini 2. This is because the front feet are slightly different. Without an answer we will send the model suitable for the Mini2.
Finally a landing gear that can be mounted anytime, without limitations!
Appli-Bet offers a set of "extensions" to the landing gear for Mavic Mini and Mini2. It is composed of 4 separate pieces that engage to the four arms of the drone. The realization with carbon rods with a diameter of only 2 mm is very strong and light and does not affect the aerodynamics during the flight of the drone.
The undercarriage raises the drone more than 5 centimeters above the ground allowing takeoff and landing from grassy or stony ground without danger of impact with the propellers, especially the rear ones that are very close to the ground.
The two front rods snap into the tips of the drone's front landing gear. The two rear rods attach to the two rear arms by means of snap-on elastic clips with carbon pin hinge.
Seven color versions are available:
Black carbon rods with glossy black PETG molded parts.
Black carbon rods with high visibility orange PETG printed parts.
Black carbon rods with parts printed in neutral 6/66 NYLON*.
Rods in black carbon with parts printed in NYLON 6/66 fluorescent yellow*.
Black carbon rods with parts printed in red NYLON 6/66*.
Black carbon rods with parts in NYLON 6/66 green*.
Black carbon rods with parts printed in NYLON 6/66 blue*.
*Nylon has better mechanical characteristics, resists shocks better, is practically unbreakable, weighs 10% less than PET.
Assembly:
The two front extensions equipped with a push fit should be inserted onto the tips of the front arms with the carbon rods facing forward. Apply enough pressure to get a firm enough fit to prevent detachment during flight.
The two rear extensions attach to the rear arms about an inch away from the motors. Take care that the levers close towards the rear direction. Correct assembly is achieved when you notice a firm "click" of the latch. For disassembly, use your fingernail to unlock the locking lever.
Before folding the arms of the drone it is necessary to remove the extensions.
Dimensions:
Front mm h 57 mm
Rear mm h 75 mm
Drone elevation from the ground: 55 mm.
Weight of the set of 4 pieces:
7,9 grams black and orange PET version.
7,2 grams Nylon version