无标题 1
1. Shipping list
|
1PC
|
Close
loop stepper motor(with
118 inch Power Cable)
|
|
1pc
|
Close loop stepper drive
|
|
1PC
|
Encoder cable(118 inch)
|
2.
Drive Specifications& Feature
|
Type
|
DSP Closed loop vector control stepper drive
|
|
maximum peak current
|
5A
|
|
Impulse response frequency
|
200Khz
|
|
Micro-stepping driver
|
200~51200ppr
|
|
Voltage
|
DC24-60V
|
|
Protective function
|
Over voltage, over current, tracking error, overproof
|
|
Signal input
|
Support PUL/DIR and CW/CCW modes (difference)
Compatible 5~24V signal (Don't need a resistor)
|
|
Continuous overload
|
Output an alarm signal
|
|
Type of cooling
|
Air-cooling
|
|
Environment
|
Keep away from dust, oil, corrosive gas, high humidity and high
vibration
|
|
Application temperature
|
0~50 degree
centigrade
|
|
Humidity
|
40-90%RH
|
|
Shake
|
10~55Hz/0.15mm
|
|
|
Min
|
Typical
|
Max
|
Unit
|
|
Output Current
|
-
|
-
|
5
|
A
|
|
Input Voltage
|
24
|
36
|
60
|
VDC
|
|
Logic Signal Current
|
7
|
10
|
16
|
mA
|
|
Pulse input frequency
|
-
|
200
|
-
|
kHz
|
|
Isolation Voltage
|
500
|
-
|
-
|
Mohm
|
3. Motor Specifications& Feature
|
Step angle
|
1.8degree +/-5%
|
|
Phase
|
2 phase
|
|
Rated voltage
|
3.4V
|
|
Rated current
|
4A
|
|
Resistance
|
1.15 ohm +/-10%(At 20 degree
centigrade)
|
|
inductance
|
3.6mH +/-20%/Phase
|
|
Hold torque
|
3.6N.m
|
|
Insulation
|
B
|
|
Rotor inertia
|
800g.cm2
|
|
weight
|
1.4kg
|
4. Advantage
1.
HBS57 uses
advanced motor control DSP chip and vector loop control technology.
2. High
control precision and reliable, low noise and little vibration,
no step to lose
.
3.
When the motor is continuously overloaded, the driver will output an alarm
signal in time, which has the same reliability as the AC servo system.
5. Application
area
It is suitable for all kinds of small and medium-sized automation equipment and
instruments, such as: engraving machine, wire stripping machine, cutting
machine, laser machine, plotter, CNC machine tool, automatic assembly equipment,
electronic processing equipment, textile and garment equipment. It is especially
effective in applications where users expect low noise and high speed.
QA:
1.Power LED does not light after power
1.Check the connection of the power line.
2.the voltage maybe too low
2.Red light warning
1.check the connection of the motor with power,
2.input voltage of the driver maybe too high or too low
3.The motor do not turn when the pulse input
1.Whether the pulse input of the driver is connected stably
2.Whether the input way in the system configuration of the driver is pulse input
3.Whether the motor can be released
4.Red light alarm after running a small angle
1.Whether the phase wire of the motor is correctly connected. If it is
not correct, please refer to the motor phase and the corresponding phase
sequence of the driver.
2.In the driver configuration parameters, whether the number of motor encoder
lines is consistent with the connected motor parameters. If they are different,
you need to reset them.
3.Whether the pulse input speed is greater than the rated speed of the motor
to us if satisfied with the our item or service. 
