2021 New Thinkcar Thinkscan Plus S6 5-Inch Professional Automotive Code Reader Tester 4 System with Free 5 Reset Function(Oil/SAS/TPMS/EPB/ETS RESET)+Free Upgrade More than 100+ Car Brands + Wifi connection Engine/SRS/ABS/Transmission System Test OBD2 Scanner Thinkscan Plus S6 PK CRP909/CRP909X/MK808
This car obd2 scanner is capable of reading and clearing trouble codes of ENGINE/ABS/SRS/Transmission.
You can diagnose the engine system via ecu obd2 port, support all 10 OBDII test modes, such as live data, O2 sensor test, component test and more;read and clear the engine error codes, find out the exactly problem, repair it, and turn off the MIL engine light.
Diagnosing an ABS problem should always start with a visual inspection of all brake components, next you will need to retrieve ABS codes to tell you where the problem is, and this is what this scanner does for you.
safety restraint system, is made up of impact sensors, a control module, and the airbags themselves, and this diagnostic device can detect every electronic parameter to check its health status.
5 free reset functions Oil/SAS/TPMS/EPB/ETS RESET, others if necessary, please pay for purchase.
1. Oil Reset .The lightening of the car maintenance light indicates that the vehicle needs maintenance.Reset themileage or driving time to zero after the maintenance, so the maintenance light will go out and the systemwill start a new maintenance cycle.
2. Elec.Throttle Adaption Elec. Throttle Adaption is to utilize the car decoder to initialize the throttle actuator so that the learningvalue of the ECU returns to the initial state.By doing these, the movement of the throttle (or idle motor)can be more accurately controlled, thus adjust the intake volume.
3. Steering Angle Reset
To reset the steering angle, first find the relative zero point
position for the car to drive in straight line.Taking this position as
reference, the ECU can calculate the accurate angle for left and right
steering.After replacing the steering angle position sensor, replacing
steering mechanical parts (such as steeringgearbox, steering column, end
tie rod, steering knuckle), performing four-wheel alignment, or
recoveringcar body, you must reset the steering angle.
4. Battery Matching
This function enables you to perform a resetting operation on the
monitoring unit of vehicle battery, inwhich the original low battery
fault information will be cleared and battery matching will be done.
5. ABS Bleeding
When the ABS contains air, the ABS bleeding function must be performed
to bleed the brake system torestore ABS brake sensitivity. lf the ABS
computer,ABS pump, brake master cylinder, brake cylinder, brakeline, or
brake fluid is replaced, the ABS bleeding function must be performed to
bleed the ABS.
6. Break-pad Reset
lf the brake pad wears the brake pad sense line, the brake pad sense
line sends a signal sense line to theon-board computer to replace the
brake pad.After replacing the brake pad, you must reset the brake
pad.Otherwise, the car alarms.
7. DPF Regeneration
DPF regeneration is used to clear PM (Particulate Matter) from the DPF
filter through continuouscombustion oxidation mode (such as high
temperature heating combustion, fuel additive or catalyst reducePM
ignition combustion) to stabilize the filter performance.
8. Gear Learning The crankshaft position sensor learns crankshaft gear machining tolerance and saves to the computerto more accurately diagnose engine misfires. lf gear learning is not performed for a car equipped withDelphi engine, the MlL turns on after the engine is started.The diagnostic device detects the DTC P1336'gear not learned'. In this case, you must use the diagnostic device to perform gear learning for the car.After gear learning is successful, the MIL turns off. After the engine ECU, crankshaft position sensor, orcrankshaft flywheel is replaced, or the DTC 'gear not learned" is present, gear learning must be performed.
9. IMMO Service
To prevent the car being used by unauthorized keys, the anti-theft key
matching function must beperformed so that the immobilizer control
system on the car identifies and authorizes remote control keysto
normally use the car. When the ignition switch key, ignition switch,
combined instrument panel,ECu,BCM, or remote control battery is
replaced, anti-theft key matching must be performed.
10. Injector Coding Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder soas to more accurately control or correct cylinder injection quantity. After the ECU or injector is replaced,injector code of each cylinder must be confirmed or re-coded so that the cylinder can better identifyinjectors to accurately control fuel injection.
11. TPMS Reset After the tire pressure MIL turns on and maintenance is performed, the tire pressure resetting functionmust be performed to reset tire pressure and turn off the tire pressure MIL.Tire pressure resetting mustbe performed after maintenance is performed in the following cases: tire pressure is too low, tire leaks, tirepressure monitoring device is replaced or installed, tire is replaced, tire pressure sensor is damaged,andtire is replaced for the car with tire pressure monitoring function.
12. Suspension Matching
This function can adjust the height of the body. When replacing the
body height sensor in the airsuspension system, or control module or
when the vehicle level is incorrect, you need to perform thisfunction to
adjust the body height sensor for level calibration.
13. AFS Reset
This feature is used to initialize the adaptive headlamp
system.According to the ambient light intensity, theadaptive headlamp
system may decide whether to automatically turn on the headlamps, and
timely adjustthe headlamp lighting angle while monitoring the vehicle
speed and body posture.
14. A/T Learning
This function can complete the gearbox self-learning to improve gear
shifting quality. When the gearbox isdisassembled or repaired (after
some of the car battery is powered off), it will lead to shift delay or
impactproblem. In this case, this function needs to be done so that the
gearbox can automatically compensateaccording to the driving conditions
so as to achieve more comfortable and better shift quality.
15. Sunroof Initialization
This function can set the sunroof lock off, closed when it
rains,sliding / tilting sunroof memory function,temperature threshold
outside the car etc.
16. EGR Adaption This function is used to learn the EGR (Exhaust Gas Recirculation) valve after it is cleaned or replaced.
17. ODO Reset
a) ODo reset is to copy,write, or rewrite the value of kilometers in
the chip of odometer by using a car diagnostic computer and data cable,
so that the odometer shows the actual mileage. b)Usually when the
mileage is not correct due to the damaged vehicle speed sensor or
odometer failure, it is necessary to do ODo reset after maintenance.
18. Airbag Reset
This function resets the airbag data to clear the airbag collision
fault indicator. When the vehicle collidesand the airbag deploys, the
corresponding fault code of the collision data appears, the airbag
indicatorlights up, and the fault code cannot be cleared. Since the data
inside the airbag computer is disposable,it is required that all new
accessories must be replaced, but after performing this function, the
data of theairbag computer can be recovered and the fault code can be
cleared, the airbag light will go out, and theairbag computer can
continue to use.
19. Transport Mode
ln order to reduce power consumption, the following functions may be
disabled,including limiting thevehicle speed, not waking up the door
opening network, and disabling the remote control key, etc. At thistime,
the transport mode needs to be deactivated to restore the vehicle to
normal.
20. A/F Reset This function is applied to set or learn Air/Fuel ratio parameters.
21. Stop/Start Reset This function is used to open or close the automatic start-stop function via setting the hidden function inECU(provided that the vehicle has a hidden function and supported by hardware).
22. Nox Sensor Reset NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust. lf theNOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalyticconverter learned value stored in the engine ECu.
23. AdBlue Reset (Diesel Engine Exhaust Gas Filter) After the diesel exhaust treatment fluid (car urea) is replaced or flled up, urea reset operation is required.
24. Seat Calibration This function is applied to match the seats with memory function that are replaced and repaired.
25. Coolant Bleeding Use this function to activate the electronic water pump before venting the cooling system.
26. Tyre Reset This function is used to set the size parameters of the modified or replaced tire.
27. Windows Calibration This feature is designed to perform door window matching to recover ECU initial memory, and recover theautomatic ascending and descending function of power window.
28. Language Change This function is used to change the system language of the vehicle central control panel.