Fully Serviced!

1964 (M4) USA made TE-11 12 Hour Dial Military Cockpit Panel Clock.

This is Numbers Matching case back (M4), and pillar plate (M4 214H).

12 hour dial and hand set (with the correct factory painted Railroad Hour and Minute hands and "Fils" style Sweep Second Hand that was used on these models of this clock). 

1  1/4" x 1  1/4" x  1/2" deep (plus contact points). 

I installed this in table top "menu holder" with a friction fit so that it can be removed easily. 

It is also easy to change the time and battery. 

I added a photocopy of  Accutron information from one of their brochures and two USPS stamps. 

It is easy to change out or remove if you prefer to install a different photos.

The display is approx. 7" w x 5" h.

InFamous.

Iconic.

Historic.

ThE Most Important Timepiece in History.

ThE Accutron 214.

NOTHING else compares.

LONG before Omega hitched a ride... on the coattails of Accutron...
This was in Space.
In Satellites.
On Astronaut's wrists.
In Rockets.

Then Omega bought a ticket to ride...

Back Set!

Electro Magnetic Tuning Fork!

The first successful, and BEST, Electronic Timepiece!

The only timepiece that MUST be in every Watch Lovers collection!

The Caliber 214H (Hack) Tuning Fork movement.

Thoroughly cleaned inside and out.

Original mineral glass crystal.

Disassembled the case and bezel to deep clean/lubricate/reset.

This is adjusted the conventional way that Accutrons are set... 

from the back set crown. 

The original deep/multi level Pillar Plate that is typical in these TE-11 Clocks was not available... so I built a case back date code matching standard caliber 214H movement and installed a plastic movement retainer inside the case to retain it. I also "made" a longer stem to reach the adjustment wheel. So time setting is as normal. 

Regarding battery changes... because the movement sits deeper into the case... the battery hatch spring is not needed (it won't reach the battery). I reversed the case back spring to hold down the battery. So battery changes aren't out of the norm... except the battery sits deeper into the case and you will move the spring out of the way (through the battery hatch) to remove the battery... and move it back to seat the battery and "close the electric circuit" to start the watch running (without having to remove the case back). The battery is actually much easier (this way) to change than a Caliber 218 watch. 

Fully disassembled the movement for cleaning/lubrication/regulation.

Disassembled, cleaned and oiled all of the friction points and regulated the timing to run properly on the modern readily available and inexpensive 1.55v 387S battery (or 394 if you already have the plastic battery insulator).

ALL friction points and setting crown greased/oiled.

New "Clark" 735 & 736 Battery Hatch and Case Back Gaskets installed.

Fully disassembled and cleaned the case including the battery cover and back set crown.

This is the original and correct case back, bezel, hands, and finishes.

This has been adjusted to run "Dead on balls accurate," as Marisa Tomei (My Cousin Vinny) would say... within the original Bulova Spec's for the time of issue. 

No need for any "tricks" or add ons that might upset the Coil Assembly.

"Why fix it if it ain't broken?"

No need for changes to the Electronics.

No need to alter and stress the electronics on this beauty... thereby devaluing it!

Why "coat" the Coils... adding stress and trapping the windings and limiting movement?

70% of the Coil issues are on the Battery side (due to owners using incorrect batteries back in the day)... NOT the Component side!

Stop wasting time over-bidding Frankensteined FAKES, from the U.K., when you can have the genuine article.

Why buy an over "engineered" parts bin mess from a part-time "hobbyist" who throws together a multitude of parts?

What value does that have now... much less in the future?! It'll be nothing more than what it is... an altered mess and a future candidate as a parts bin part out. That's what they were assembled from now... and that's how they will be "utilized" in the future!

I use the Mobius products that were specified by Bulova and I install new gaskets.

I work on these the Old School way.

I am not a Part Time Hobbyist doing this after my day job... and I see no reason to alter these... it only decreases their value.

The goal is to get these right... so that we can enjoy and preserve these Historic works of Horology/Engineering/Art.

I send these out double boxed to protect them, with a multi page Instruction Set, an extra battery, insured, with Signature Confirmation Service... and I hand deliver them to USPS for receipt in hand so that we are BOTH covered!

I do these RIGHT because I LOVE them. 

If you want cheap, badly thrown together FAKE CRAP at a "low" price point... I'm NOT "your guy!"

There are plenty of people out there destroying classic Accutrons (look for the Chop Shops in CA, the UK, PA, FL, OR, VA, GA, Bulgaria, etc. spitting out parts bin Frankensteins by the dozens to unsuspecting noobs).

Would you accept this behavior for cigars, cars, watches, etc.?! 

SAVE the 214!

Be the ONLY one on YOUR block!