*Compatibility Chart:

1, You can distinguish specific model of an automobile by VIN(Vehicle Identification Number).

2, VIN(Vehicle Identification Number) consists of total 17 English letters and arabic digits.

3, VIN does not include the letters I (i), O (o), and Q (q) (to avoid confusion with numerals 1 and 0).

Infiniti QX56 2004-2010

Nissan Armada 2005-2015

Nissan Pathfinder 2004

*Generation & Evolution:

Infiniti
JA60 First generation (2004-2010)
Z62 Second generation (2011-present)
 

Nissan Armada

TA60 First generation(2004-2015)

Y62 Second generation(2016–present)

Nissan Pathfinder

YD21 First generation(1985-1995)

R50 Second generation(1996-2004)

R51 Third generation(2005-2014)

R52 Fourth generation(2015-2020)

R53 Fifth generation(2021-Present)

*Platform Drive Layout:

Base Model-Rear Wheel Drive Layout

4Matic Model-Four Wheel Drive Layout

*Air Suspension Structure:

10  A221 320 03 04  Compressor Unit
10  A221 320 07 04  Compressor Unit
10  A221 320 09 04  Compressor
10  A221 320 16 04  Compressor Unit
10  A221 320 17 04  Compressor
20  A220 327 03 76  Washer
30  A220 327 08 30  Rubber Bumper
40  A220 993 03 01  Spring
50  A220 327 02 53  Spacer Tube
60  N910112 005000  Hexagon Nut
70  A005 997 62 90  Cable Strap
80  A000 995 96 77  Line Holder
90  A221 320 02 43  Bracket
100  A212 320 03 58  Valve Block
100  A251 320 00 58  Valve Block
105  A000 327 00 69  Connector
108  A221 328 00 65  Connection Pipe Socket
110  A005 990 25 12  Bolt
120  A221 320 14 43  Bracket
130  A221 327 02 30  Rubber Bumper
140  A221 327 09 45  Pressure Line
140  A221 327 30 45  Line
160  N000000 003477  Nut
170  N910105 008004  Hexagon Head Bolt
170  N910143 008002  Hexalobular Bolt
180  N000000 003175  Nut
190  A221 320 03 69  Filter
200  A211 327 00 11  Retaining Collar
210  A220 320 00 69  Filter
220  A140 995 01 05  Spring Hose Clamp
230  N910143 006001  Hexalobular Bolt
250  A221 327 16 45  Pressure Line
260  A221 320 00 15  Pressure Accumulator
265  A000 327 03 69  Connector
280  A220 327 10 45  Pressure Line
290  A000 327 01 69  Connector
900  A168 545 29 28  Receptacle Housing
900  A168 545 36 28  Pin Bushing Housing
901  A000 540 41 05  Electrical Cable
901  A000 545 71 80  Gasket
901  A009 545 81 26  Female Contact
910  A046 545 89 28  Plug
911  A002 997 60 86  Stop Plug
911  A003 997 77 49  Gasket
911  A015 545 72 26  Contact Spring
911  A015 545 73 26  Contact Spring

*Removal Guideline:

Caution: Damage to the vehicle and air suspension system can be incurred if work is carried out in a manner other than specified in the instructions or in a different sequence.
1.To avoid the possibility of short circuits while working with electric components consult your owner's manual on how to disconnect your battery.
2.Consult your vehicle owner's manual, service manual, or car dealer for the correct jacking points on your vehicle and for additional care, safety and maintenance instructions. Under no circumstances should any work be completed underneath the vehicle if it is not adequately supported, as serious injuries and death can occur.
1.Set steering to straight.
2.Raise vehicle.
3.Remove the front skid plate from underneath the vehicle to expose the air suspension’s compressor.

4.Locate and remove the air line from the compressor. Remove the air line fitting from the air line and discard.

5.Locate and remove the two(2)electrical connectors from the compressor.

6.Pinch and slide the clamp off of the fitting to remove the larger rubber hose from the compressor.

7.Locate and remove the three(3)mounting nuts holding the compressor to the vehicle.

8.Remove the compressor and mounting hardware from the vehicle.

*Installation Guideline:
Installation is in reverse order of air suspension compressor pump removal.

*Warning & Ntice:

1.When the air compressor being replaced, the matching relay must be replaced according to the corresponding vehicle. If there is something wrong with the relay which leads the compressor to continuous operation without any break, it will burn out the electric motor or other plastic part.

2.When the air compressor being installed, the critical parts such as rubber shock pad and damping spring must be fully fixed on the stand without short installation or missing installation (The air compressor is unequipped with parts). With the anti-vibration parts of short installation or missing installation, a loud noisy instance will happen when the air compressor is working for the sake of resonance.

3.Distribution valve, shock absorber, air tank and tube connector must be checked after air compressor installed to ensure air-tightness. The lifespan of the air compressor will be shortened if the leakage exists.

4.Increased noises while the compressor is running may be caused by a non-functioning compressor mounting. Change the rubbers and springs of the mounting in any case.

5.A porous intake hose often is the cause for a breakdown of the compressor. Change the intake hose and preferably also the filter and noise absorber, because we do not want the compressor to breakdown because of these.

6.Change the relays before installing the compressor even if it seems to still work. This is also a specification by the car manufacturer. Be sure to change the right relays. Relays look similar, that is why there is a risk to change the wrong relays.

7.Be sure to check whether the system is leakproof after repairing. The easiest way to do this is to park the vehicle. Wait for the system to automatically re-adjust if your car has this feature. Then measure the heights from the ground to the lower edge of the fender as exactly as possible and take notes. On the day after measure these heights again and compare them with the ones before. Even a small difference will lead to a damaged compressor and damaged valves in the long run.

*OEM Part Number:

534007S600 53400-1LA4C, 53400-1LA4A, 53400-1LA4B, 534001LA4C, 534001LA4A, 534001LA4B, 53400 1LA4C, 53400 1LA4A, 53400 1LA4B