433MHz DC 12V 1CH Wireless Switch Mini Relay Module with RF Remote Control Set
Technical Data Of Receiver:
Input Power:DC10V-14V
Standby Current:<5MA
RF Frequency:315M or 433M
RF working mode:superheterodyne
Receive sensitivity: >97dbm
Transmitting distance:>100m ( open space)
Decoding mode:MCU software decoding
Remote storage:25pcs
Support remote type: Learning code, Fixed code(Rolling code can be design)
Working mode:Momentary, Toggle, Latching Time delay (5s ,10s ,15s )
Wiring type:fixed terminal
Output Terminal :NO , NC , COM
Dimension of PCB:35*30*18mm (L,W,H)
Remote Controller: power by 2x CR2016(not included)
Wiring diagram 1:
+V : 12V + input ;
- V: 12V - input ;
NO: Output , normal open;
COM:Output , common ;
NC: Output , normal close.
Specifications Of The Remote Control:
Operating frequency: 433.92MHz
Power by 2pcs 3V Coin Cell Button Battery (Battery NOT included ),
Material: PVC.
Button: 2 buttons
Size: 59mm x 28mm x 8mm;
Operating voltage: 6V ;
Operating Current: 12mA
Transmitting power: 10mw
Modulation mode: ASK (AM).
Encoding type: Learning.
Transfers distance: 80m
Notice:
Different options include different packages:
About Working mode:
Momentary:Push the remote button , the relay connects, release the remote button , the relay dis-connects.
Toggle:Push once the remote button , the relay connects , push twice the remote button , the relay dis-connects .
Latching:Push the remote button A, the relay connects, push the remote button B, the relay dis-connect.
Time delay mode :Push the remote control button , the relay connects , from when release the remote button , after 5s or 10s or 15s , the relay disconnect automatically.
Clearing the code :
Momentary:Push the remote button , the relay connects, release the remote button , the relay dis-connects.
Toggle:Push once the remote button , the relay connects , push twice the remote button , the relay dis-connects .
Latching:Push the remote button A, the relay connects, push the remote button B, the relay dis-connect.
Time delay mode :Push the remote control button , the relay connects , from when release the remote button , after 5s or 10s or 15s , the relay disconnect automatically.
Clearing the code :
Push the learning button on the receivers for 8 times , the codes will be cleaned;
After clearing the code, all the remote control cannot work any more.
Learning the code :(momentary)
Push the learning key on the receiver once time , it comes into momentary setting mode .
Wait for a moment , the LED will be on, it comes into learning state .
Push the remote button , LED indicator on the receiver board will flash 3 times and then come off,
learning successfully .
Learning the code : ( Toggle )
Push the learning key on the receiver twice time , it comes into toggle setting mode
Wait for a moment , the LED will be on , it comes into learning state .
Push the remote button,LED indicator on the receiver board will flash 3 times and then come off,
learning successfully .
Learning the code :( Latching )
Note: When you choose for latching mode , in order to learn more remote control , you need to learn two different button , the first time learnt is for “ON”, the second time learnt for “OFF”.
For example : button A = ON , button B = OFF
Push the learning key on the receiver triple time , it comes into latching mode .
Wait for a moment , the LED indicator on the receiver board will be on,
Push the remote button A,
LED flash for 3 times .
Push the remote button B .
Led indicator flash for 3 times and then come off,
learning successfully.
A = ON , B = OFF .
Learning the code :( Time delay mode )
Push the learning key on the receiver forth time , the time dealy for 5 seconds .
Push the learning key on the receiver fifth time , the time delay for 10 seconds .
Push the learning key on the receiver sixth time , the time delay for 15 seconds .
The LED indicator will be off .
Push the remote button , LED flashes and off .
After 3 seconds , the LED indicator will be on again , learning successfully .
NOTE: The system can store for 25 pcs of remotes , if the remote get more than 25 pcs , the initial remote control will be lost .
Learning the code :(momentary)
Push the learning key on the receiver once time , it comes into momentary setting mode .
Wait for a moment , the LED will be on, it comes into learning state .
Push the remote button , LED indicator on the receiver board will flash 3 times and then come off,
learning successfully .
Learning the code : ( Toggle )
Push the learning key on the receiver twice time , it comes into toggle setting mode
Wait for a moment , the LED will be on , it comes into learning state .
Push the remote button,LED indicator on the receiver board will flash 3 times and then come off,
learning successfully .
Learning the code :( Latching )
Note: When you choose for latching mode , in order to learn more remote control , you need to learn two different button , the first time learnt is for “ON”, the second time learnt for “OFF”.
For example : button A = ON , button B = OFF
Push the learning key on the receiver triple time , it comes into latching mode .
Wait for a moment , the LED indicator on the receiver board will be on,
Push the remote button A,
LED flash for 3 times .
Push the remote button B .
Led indicator flash for 3 times and then come off,
learning successfully.
A = ON , B = OFF .
Learning the code :( Time delay mode )
Push the learning key on the receiver forth time , the time dealy for 5 seconds .
Push the learning key on the receiver fifth time , the time delay for 10 seconds .
Push the learning key on the receiver sixth time , the time delay for 15 seconds .
The LED indicator will be off .
Push the remote button , LED flashes and off .
After 3 seconds , the LED indicator will be on again , learning successfully .
NOTE: The system can store for 25 pcs of remotes , if the remote get more than 25 pcs , the initial remote control will be lost .
