PIR Motion Sensor Dimming Controller
● PIR motion sensor dimming controller with daylight detection.
● 3 button operation, 6 indicator lights.
● 3 work modes.
● 5 level dimmer.
● 6 level timer.
● Optional RF 2.4G single-zone or multi-zone dimming remote control.
● Work as RF remote, output RF 2.4G signal, matched with RF LED controller or RF dimmable LED driver optional.
● 3M tape installation, easy and convenient.
● Suitable for kitchen, cabinets, stairs, bedrooms, closets, living rooms, aisles and so on
Specification,
Input voltage: 5-24VDC
Output voltage: 5-24VDC
Input current: 3.5A
Output current: 3A
Output power: 15-72W
Sensitivity angle: 120°
Sensing range: 2-7m
Input signal: PIR sensor + RF 2.4GHz
Control distance: 30m(Barrier-free space)
Dimming gray scale: 256 levels
Dimming range: 10 -100%
Size: L90 x W48 x H40mm
![](https://image.pushauction.com/0/0/2e6c3252-181c-496f-a7f5-1ba329f989db/cb7eeffb-6cdf-4559-a538-9f8079988bfe.jpg)
![](https://image.pushauction.com/0/0/2e6c3252-181c-496f-a7f5-1ba329f989db/570ecfc7-a412-4e08-8022-971955d90533.jpg)
Auto-sensing mode
In auto-sensing mode, turn on the light when the PIR sensing probe detects human movement, and turn off the light with automatic delay after the person leaves.
In auto-sensing mode, set the sensing delay off time through time delay button (10-600 seconds),
and adjust the light brightness through brightness button (10-100%).
Short press the time delay button to switch 6 levels of delay time: 10% (Indicator1-2 on), 25% (Indicator 1-3 on), 50% (Indicator 1-4 on), 75% (Indicator 1-5 on),
100% (Indicator 1-6 on).
Short press the brightness button to switch 5 levels of brightness:
10% (Indicator1-2 blinks once), 25% (Indicator 1-3 blinks once), 50% (Indicator 1-4 blinks once), 75% (Indicator 1-5 blinks once), 100% (Indicator 1-6 blinks once).
Auto-sensing mode is used in staircases, corridors, cupboards, bedrooms and other places where light need to be turned on by sensing.
When turning on auto-sensing mode, it is recommended to turn on daylight detection at the same time.
2. Daylight detection
DIP switch set daytime or night mode.
Daytime mode with daylight sensing turned off
Night mode with daylight sensing turned on
In daytime mode, daylight sensing is turned off and infrared motion sensing is used 24 hours a day.
In night mode, the daylight sensing function is enabled,
the light will be turned on only when the ambient light is less than the daylight sensing threshold.
The daylight sensing threshold is xed at 30 lux by default.
3. Setting the PIR sensitivity
Long press the time delay button and power button at the same time for more than 2 seconds to set the PIR sensing sensitivity:
Long press for 2 seconds, set to high sensitivity (sensing distance 4-7 meters), all indicators flash 1 time;
Long press for 5 seconds, set to medium sensitivity (sensing distance 3-6 meters), all indicators flash 2 times;
Long press for 10 seconds, set to low sensitivity (sensing distance 2-5 meters), all indicators flash 3 times
4. Setting the light off fade time
The light on fade time is fixed 1 second, the light off fade time can be set 1, 2, 3 seconds.
In the light off mode, long press the time delay button for 2 seconds to switch the three light off fade time in sequence:
1 second light off fade time, indicator 1 blinks once;
2 second light off fade time, indicator 1-2 blinks once;
3 second light off fade time, indicator 1-3 blinks once
5. Restore factory settings
Long press the power button and brightness button at the same time for 10 seconds to restore the factory settings, all the indicator lights flash 2 times.
Factory default parameters: auto-sensing mode, PIR sensing high sensitivity, 100% brightness, sensing delay off time 30 seconds, light off fade time 1 second.
Match Remote Control (Optional)
The PIR motion sensor dimming controller EV-R can be equipped with an optional RF remote to realize both sensor control and remote control at the same time.
When set to auto-sensing mode by the power button, the light can also be switched on/off or the brightness can be adjusted by the remote control,
and the sensor dimming controller maintains the auto-sensing mode unchanged
Match:
Long press the Power button and Brightness button at the same time for more than 2s,
all LED indicator flash once means it enters the remote control match state.
Immediately press on/off key (single zone remote) or zone key (multiple zone remote) on the remote.
all LED indicator flash 3 times means match is successful
Delete:
Long press the Power button and Brightness button for 5s to delect all match,
all LED indicator flash 5 times, means all matched remotes were deleted.
Work as RF Remote
The PIR can be matched with one or multiple RF LED controller or RF dimmable LED driver,motion sensor dimming controller EV-R
including single color, dual color, RGB, RGBW, RGB+CCT light type, turn on or turn off the other light by motion detection.
Notice for installation of PIR sensor
1.If the sensor is exposed to direct sunlight, interference signal will be introduced.
2.The sensor should be installed in a dry environment and keep away from windows, air conditioner and fans.
3. Make sure that the sensor stays away from heat source, such as countertops, kitchen appliances which generate hot steam, walls and windows in direct sunlight, air conditioner, heating, refrigerators, stoves and so on.
4.There should not be shelter(screen, furniture, large bonsai) within the range of detection