Lot 1. Quantity OVER 50. SOME MAY NOT BE PERFECT CUTS. AT LEAST 30 WOULD BE CALLED “perfect”

These red and white safety warning stripe stickers are the perfect size for 1:14 scale models, but will enhance any Truck, trailer or other construction equipment from 1/10th to even 1/20th scale. (U could cut them shorter if needed) These stickers are made of waterproof ACTUAL REFLECTIVE MATERIAL, just like the real one u see going down the roads. (See photos 6 and 7).

They are compatible with Tamiya, Hercules, Double E, Traxxas, Toucan, Axial, Team Losi, Revell, or other brands or even your homemade version. They can be easily applied for an added level of realism for your equipment. These sticker are perfect to use during races or when driving in crowded areas, ensuring that your RC vehicle is visible to other drivers and reduces the risk of accidents. Upgrade your RC vehicle with this easy-to-apply safety sticker, which is essential for any serious RC enthusiast. The red and white warning stripe is eye-catching, making it easy for other drivers to spot and avoid any potential collisions. This accessory is ideal for anyone who prioritizes safety and realism and wants to enjoy their RC vehicle to the fullest.

I have included over 50 (hard to count so I just put in an extra amount in case u find some not to your liking). They are handmade, so have some minor variations in size, if u want to measure in the one thousandth scale! I have counted the number of stickers I see on many trailers and 25 per side seems to be on the high side. (So 50 total) I have seen some trailers that have stickers running from end to end with no gaps! U would need a couple of packages, especially if u want to have exact width stickers touching each other. That would show some irregularities in my cut width so I would discourage that. I have seen rear lower safety bumpers that are covered solid end to end with these sticker, and a few seconds of sorting widths can allow for that.

Full scale ones as shown in picture 4 will measure 2” wide, so at 1/14th scale it is .14 inches, so that is what most will measure plus or minus a tiny amount. The Full Scale lengths are 12” which would be about .86” at 1/14th. These will measure about .87” to .9”. VERY, VERY CLOSE TO SCALE! I doubt people will take a micrometer to ur toy!

You will be very happy with the reflective nature of these stickers, see the shine on picture 8.

Picture 1,2 and 3 are actual photos of my stickers from the batch u will receive. Photo 5 shows the other kind of safety warning stickers, and u could cut .14” wide strips out of those if u have the time and Skill! Photos 6 and 7 are actual real trailers showing the spacing and number of stickers like these u will see on Semi tractor’s trailers. I even saw them on a U-Haul! U probably won’t see a real trailer without them. So you should not build a trailer without them! I put them on my Semi trucks, and other equipment I haul (Tamiya 1/14th semi truck and Tamiya trailer frames with homemade box (wood 30’ scale or 26”)and tanker made of aluminum house roof flashing!)

I have noticed the red side goes on the left of the white side.

Installation:

U may need to use a hobby knife to remove the backing to get to the self adhesive side. U can also stick tape to the backing, then peal away the sticker. I find it easiest to stick these stickers on the end of a hobby knife to apply level on your model. They are one piece! The red side will NOT come apart from the white side! If they are going on a little crooked, u can peel them back up a little and they will stick again. Once pushed hard onto the surface, they will stay attached indefinitely - commercial grade adhesive! Waterproof! A hair dryer can help remove them. Be careful not to damage your paint or chrome removing them.

Enjoy!

Check out my eBay feedback! I am a quality, reliable EBayer and appreciate you leaving me 5 star positive feedback! If you are unhappy with the width I gave you due to my cutting error, I will send u more replacements.

Do NOT leave me negative feedback. I have been CLEAR about them being hand made!

If you are going to measure each one with a vernier caliper, DO NOT BUY THEM,

or contact me and I will send u perfect “sorted size” ones at an additional cost. These are so cheap (and I will include extras), that I plan for u to have plenty of “perfect size ones” at around 30 per lot and discard any mis-cuts. You can put wider ones on one side and narrower ones on the other side! We are talking probably .008” error! I DID NOT MEASURE THEM. I JUST CREATED A PROCESS TO CUT THEM “evenly” and in a reasonable amount of time, FROM A SHEET TO .14’ wide. EVERYONE LOVES THEM!

I try to ship next day when possible! These will come in a standard USPS mail envelope, so watch your mail!

BILL