Industrial devices Welder Fantasy JET TIG III are microprocessor welding sources based on IGBT technology, adapted to welding of carbon steel, stainless steel, acid resistant steel, copper, brass, magnesium, titanium, all aluminum alloys and plasma cutting.

Machines powered with 230 V voltage are equipped with a PFC module (Power Factor Correction) - allowing to increase the power factor to values as close as possible to 1 in order to reduce losses in industrial lines.

The highest class device sets new standards among AC / DC welding machines, and the friendly control panel ensures selection of all necessary work parameters.

JET TIG III AC / DC 200 welder allows you to work in the following modes:

- MMA DC +

- MMA DC-

- MMA VRD DC +

- MMA VRD DC-

- TIG DC

- TIG DC PULS

- TIG AC

- TIG AC PULS

- PLASMA CUT

For all TIG methods it is possible to use the following welding modes:

* ARC BURNING THROUGH LIFT-ARC (2T and 4T),

* AGGREGATE ARC OF NON-CONTACT HF (2T and 4T),

* ARC BURNING FROM REMOTE CONTROL.

NEW ADDED PANEL FUNCTIONS:

- AC / DC EASY SETUP - POSSIBILITY TO USE SCHEDULED FACTORY SETTINGS

- NORMAL SETUP - WELDING PARAMETERS ADJUSTED ACCORDING TO INDIVIDUAL NEEDS

- POSSIBILITY TO CHOOSE SHAPE OF WAVE

* ADVANCED SQUARE - rectangular

* SOFT SQUARE - trapezoidal

* TRIANGULAR - triangular

* SINE - sinusoidal

- ADVANCED AC - MIXED CURRENT AC DC

- FULL CONTROL OF MMA

- PFC

- VRD

- HOT START TIME

- HOT START AMPS

- PLASMA CUTTING FUNCTION

- PLASMA PILOT ARC (HF)

- GAS TEST

FEATURES:

* compact, compact design,

* small dimensions and low weight,

* IGBT transistors,

* 60% efficiency,

* easy to use control panel,

* LCD display of welding parameters,

* LCD display of an individual program,

* the ability to save full 9 programs,

* a very wide range of welding functions:

- HF - the device is equipped with an ioniser, which allows for contactless inspection of the welding arc.

- PRE and POST GAS - gas flow before and after welding.

- UP and DOWN SLOPE - welding current rise and fall.

- STANDARD AC / DC - pulse current function, is mainly used for welding thin elements (even 0.1mm thick), metals with a low melting point, e.g. lead, or welding in forced positions. Other advantages of pulsating current welding are a smaller zone of heat influence, higher arc stability and a greater depth of penetration and an improved appearance of the weld face.

- ADVANCED AC - AC DC mixed welding -. In a single cycle, there is a transition between alternating current AC and DC with negative polarity DC (-). This cycle is repeated throughout the welding process. Mixed current welding is particularly useful when joining elements of different thickness. The noise emission is also reduced compared to AC welding.

- HOT START - a function that increases the current when the arc is ignited, facilitating the start of welding.

- ARC FORCE - a function that stabilizes the welding process, by maintaining the value of the welding arc, regardless of its length, and facilitates control over the amount of spatter.

PANEL FUNCTIONS:

* MMA current,

* AC TIG current,

* TIG DC current, PULSE,

* pre-gas, post-gas,

* rising and falling of the current,

* HOT START,

* MMA ARC FORCE,

* 2-TAKT and 4-TAKT,

* HF contact and contact LIFT ignition,

* the possibility of connecting remote control,

* dual-function ADJUST knob (coarse and fine adjustment).

COMPLETE SET CONTAINS:

- Welder Fantasy JET TIG III AC / DC 200 IGBT welder,

- PARKER SUREGRIP SGT26 FLEX TIG SRT 26-4m welding torch - with welding current adjustment,

- mass holder 3m,

- electrode holder 3m,

- P80-4m plasma holder,

- additional operating elements (nozzles, connectors, sleeves, electrodes),

- trolley for plasma torch,

- filter-reducer of compressed air,

- instruction manual and warranty card.

TECHNICAL DATA:

• Power supply voltage: 1 ~ 230V 50 Hz
  
• TIG / MMA power consumption: 6 kVA
  
• Time delay protection min.: 20 A
  
• Insulation class: F
  
• The degree of housing protection: IP21S
  
• dimensions: 575 * 230 * 435 mm
  
• Weight: 27 kg
  

TIG PARAMETERS

• TIG DC welding current range: 3-200 A
  
• TIG AC welding current range: 5-200 A
  
• Efficiency of TIG 60%: 200 A
  
• TIG efficiency 100%: 160 A
  
• The course of the waveform: rectangular, trapezoidal, triangular, sinusoidal
  
• AC current frequency regulation: 20-250 Hz
  
• Current balance in AC mode: 5% -90%
  
• Gas initial / final AC / DC mode: 0-25 / 0-50 s
  
• Initial / final DC mode: 5-200 / 3-200 A
  
• Initial / final current AC mode: 5-200 A
  
• Rise / fall time AC / DC mode: 0-25 s / 0-25 s
  
• The basis of the AC / DC pulse: 3-100%
  
• The duration of the AC / DC pulse: 5% -95%
  
• Frequency of mixed current Advanced AC: 0.1-10 Hz
  
• Pulse DC Standard Pulse Frequency: 0.1-500 Hz
  
• Pulse frequency AC Standard (rectangular): 0.1-250 Hz
  
• Pulse frequency. Standard AC Soft Square, Triangular, Sine: 0.1-10 Hz
  
• TIG arc ignition function: HF (ionizer) / LIFT
  

MMA PARAMETERS

• Idle speed MMA / VRD MMA: 70/21 V
  
• Welding current range MMA DC + / DC-: 20-160 A
  
• MMA efficiency 60%: 160 A
  
• MMA efficiency 100%: 130 A
  
• ARC FORCE: 0-100%
  
• HOT START TIME: 0-2 s
  
• HOT START AMPS: 0-100%
  

PLASMA PARAMETERS

• Cutting current range: 20-50 A
  
• PLASMA efficiency 60%: 50 A
  
• PLASMA efficiency 100%: 40 A
  
• Cutting thickness: 12 mm
  
• Air intake: 150-300 l / min
  

All our products are stored in our European warehouse for which orders placed before 1.00PM GMT are shipped the very next day (or day after), and delivered within the next 3 to 5 working days to any place in the continental European Union.

*Deliveries to remote places in the European Union like Malta, Cyprus, Ireland, or outside of the EU like Iceland or Norway, etc might take longer, and cost more than indicated in the listings description, eBay doesn’t see the difference between European countries like Germany or Asiatic part of Russia, and set one shipping charge to all of them. Please contact us to evaluate shipping costs to your place.

Buyers who live outside of the European Union, please note that you will face customs duties and taxes when the parcel arrives in your country. As a buyer you are responsible to pay any custom duties, and taxes imposed by your government. We are not responsible for customs duties in the buyer's country, and cannot pay it. Please take this into account when making a purchase with us.

For any order which shipping cost cannot be calculated at the time of checkout, we will calculate the shipping cost after the order has been placed. We will then contact you via eBay messaging system, and ask you to pay the balance between the real shipping cost and the charge you have already paid.

We take unprecedented measures to guarantee your things arrive securely and in place. Every product goes through a stringent checking process before it is shipped to guarantee that the product reaches you unharmed.

The Grey Eagle Shop accepts eBay payments, PayPal, credit/debit cards and bank transfers.

On eBay listings we accept eBay payments, if you choose to use other payment methods please get in touch with us. Please be aware that if your card issuer does not authorise payment, Grey Eagle Shop will not be liable for any resulting non-acceptance of the order or any resulting delivery delay. We also reserve the right to request further proof of identification and age on any order placed using a debit/credit card.