Please do not leave any negative feedback without contact us first.thank you.


For the installation system, please Note:


XPROG 5.55 : Can only support WIN 7 32BIT computer system


XPROG 6.26 : Can only support WIN 7 64BIT computer system


ITEM 1：XPROG V6.26 


Please Attention For Xprog V6.26 Software Installation Tips:

1. Please use the real WIN 7 64BIT system and close the anti-virus program.

2. Only one xprog version 6.26 software can be placed and installed in the computer, no other xprog software, if there are other software, it will conflict and cause certificate problems!


3. Turn on the computer network, the computer time needs to be consistent with the local time.


4. The computer needs to have 2 or more partitions, such as C and D disks. It cannot be an external hard disk, but must be multiple partitions of the computer's hard disk.


5. MUST first install 6.26 registry, then run V6.26 Software.


6. The product cannot open multiple software interfaces at one time, which will cause the product to enter a locked state! ! Because the system will mistakenly believe that you use the product incorrectly or crack the product, resulting in lock-up.


7. Product can't be updated.


8.After used,close the software and unplug the usb dongle from the computer.


Please must follow this instructions to run software,otherwise device will not installed.



Please MUST READ This :
1. Which XPROG version you use , before open software MUST install the right version registry. Otherwise it will runs old version registry automically and then confilt with new hardware and device dead.
2. If your computer no install other old xprog version,it also require install right registry ,otherwise device runs fault and defective .



ITEM 2:XPROG V5.55


Highlight of XPROG 5.55:


New Software Version:V5.55

V5.55 Especially For BMW CAS4 DECYPATION

System Requirement: WIN7 32bits Only (close an-virus program,or soft ware attacked)

Add new authorization:AUTH-0025 Authorized 11/4/2014


Without USB Dongle,Software is not encrypted.Feel free to install software.




Please Attention For Xprog V5.55 Software Installation Tips:

1. Please use the real WIN 7 32BIT system ，Turn off the network and anti-virus programs. Product can't be updated.

2. Only one xprog version 5.55 software can be placed and installed in the computer, no other xprog software, if there are other software, it will conflict and cause certificate problems!

3. The computer needs to have 2 or more partitions, such as C and D disks. It cannot be an external hard disk, but must be multiple partitions of the computer's hard disk.

4. MUST first install 5.55 registry, then run 5.55 Software.

5. The product cannot open multiple software interfaces at one time, which will cause the product to enter a locked state! ! Because the system will mistakenly believe that you use the product incorrectly or crack the product, resulting in lock-up.

6.After used,close the software and unplug the usb dongle from the computer.

7.Product cannot be updated.




Note For XPROG V5.55:

1. There is no dongle with this one.


2.Old Version like V5.0/V5.3 tool ,it can not use with this V5.55 .

3.Disconnect internet when run soft ware ,otherwise device will damaged.

4.Don't update online, or hardware broken and can not work any more.
5.Please unistall all old Xprog version clearly ,and make sure install Our XPROG 5.55 only into your PC only .
Please read and following those tips when install Xprog V5.55,otherwise hardware can not use any more .




XPROG-M V5.55 Authorizations:


AUTH-0001 for Motorola HC05 family authorization (allows to read/write EEPROM)

AUTH-0002 for Motorola HC08 family authorization (allows to read/write EEPROM)


AUTH-0003 for Motorola HC11 family authorization (allows to read/write EEPROM)


AUTH-0004 for Motorola HC12, 9S12 family authorization (allows to read/write EEPROM and flash memory)


AUTH-0005 for Texas Instruments TMS370/TMS374 family authorization (allows to read/write EEPROM)


AUTH-0006 for Motorola HC05Bxx and HC05Xxx family bypass security authorization (allows to read/write secured EEPROM and flash memory)


AUTH-0007 for ST M35080 authorization. Read/Write/Erase device to delivery state.

AUTH-0008 EWS3 authorization

AUTH-0009 ATMEGA family authorization (allows to read/write EEPROM and flash memory)


AUTH-0010 for MB ZGS001 authorization

AUTH-0011 for Motorola HC11EA9/E9 bypass security authorization (allows to bypass security bit and read EEPROM and RAM memory)

AUTH-0012 National CR16 authorization (allows to read/write EEPROM memory)

AUTH-0014 ST7, ST10 family authorization (allows to read/write internal flash)

AUTH-0015 MPC5xx authorization (depending on device program automatically detects MPC5xx, M95xxx device type, flash, external flash and configuration memory size)

AUTH-0018 for Motorola HC12, HC912, MC9S12, MC9S12X bypass security authorization (allows to read/write secured EEPROM and flash memory)


AUTH-0020 ARM (for Micronas, ...) Family authorization (allows to read/write internal flash and external serial EEPROM)


AUTH-0021 ARM (for Micronas, ...) Family bypass security authorization (allows to read/write secured and non-secured internal flash and external serial EEPROM, view/change mileage,chassis number (VIN), serial number and PIN code).

AUTH-0023-1 MAC7xxx(New added)

AUTH-0023-2 XC23xx(New added)

AUTH-0024-1 MC9S12Cxx(New added)


AUTH-0024-2 MC9S12XE(New added)


AUTH-0024-3 9S12XE SECURITY


AUTH-0024-4 MC9S12HA/HY/P


AUTH-0025-1 MPC/SPC5xxx (newly added)

AUTH-0024-4 MC9S12HA/HY/P

AUTH-0025-1 MPC/SPC5xxx (newly added)





XPROG-M V5.5.5 Adapters:

ADP-0001 TMS370 PLCC28 programming adapter

ADP-0002 TMS370 PLCC44 programming adapter

ADP-0003 TMS370 PLCC68 programming adapter


ADP-0004 for Motorola HC05B/X PLCC52 programming adapter

ADP-0005 for Motorola HC05B/X QFP64 programming adapter


ADP-0006 for ST M35080 in-circuit programming adapter

ADP-0008 TMS374 family in-circuit programming adapter

ADP-0009 MC68HC05V12 programming adapter

ADP-0010 TMS374 on-board programming adapter


ADP-0011 HC11EA9/E9 programming adapter


ADP-0017 HC(S)12 BDM / ARM Micronas in-circuit programming/bypass security adapter

Additional adaptor for 5M48H P-Flash





Computer Requires:

Processor: INTEL Pentium 60MHz or faster (depends on operating system)


Memory (RAM): 64MB (depends on operating system)


Hard drive: 20MB free space


Communication: One free physical COM or USB port


Operating system: Microsoft Windows WIN7 32Bits Only





Packing List :

1  x  XPROG Unit


19 x  Programming Adapter

1 x  USB Cable.

1 x CD Software