eBay

Power Over Ethernet Kit for 4x Raspberry Pi

(250M 4ports PoE Switch+ Micro USB PoE Splitter)

for Raspberry Pi B/B+/2/3

Support EXTEND mode, max Network Cable length to 250 meters

NOTE. When EXTEND mode enable, the Max bandwidth for the Power Link (PoE) port 1-4 network port will be reduced to 10Mbps for each one.
(The up-link is not affected, it will always working at 100Mbps max speed)

PoE Switch Specification:

ALL Port:	Standard 10/100Mbps Ethernet port. Support 10Mbps Ethernet and 100Mbps Fast Ethernet, can operate in full-duplex or half-duplex mode,must work with 4 pairs UTP Cat5/5e/6 cable。

Power Link Port 1-4:	any supported unsolicited power on pairs 45-78 pins compliant Powered Devices (PDs)

Power LED	LED ON: power on. LED OUT: power off
Green Light LINK/ACT	LED ON Indicates the port is connected to a network device and has been started
	LED OFF Indicates that this port is not connected to a network device or has not been started

Standard	IEEE 802.3 10BASE-T Ethernet
	IEEE 802.3u 100BASE-TX Fast Ethernet
	IEEE 802.3x Full-Duplex flow control
Protocol	CSMA/CD Ethernet
Data Transfer Rate	Ethernet: 10Mbps (Half Duplex) 20Mbps (Full Duplex)
Data Transfer Rate	Fast Ethernet: 100Mbps (Half Duplex) 200Mbps (Full Duplex)
IC Chips	IC Plus IP178G
Network Media(Cable)	10Base-T(EXTEND mode): UTP category 5e, 6 cable (maximum 250m) EIA/TIA-568 100Ω STP (maximum 250m)
Network Media(Cable)	100Base-TX:UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m)
PoE Power on RJ45	Power +: pin 4 & pin 5 ; Power -: pin 7 & pin 8
PoE Power on RJ45	DC Output: 52V, Per port Max 1A or 50Watt, 4 POE ports Total Max. 75Watt
Number of Ports	5 x 10/100Mbps Auto-Negotiation RJ45 ports with 4 PoE enabled (port-1 ~ port-4)
Power Input	AC Input: 110V ~ 240VAC, 50Hz ~ 60Hz.
Power Input	DC OutPut: 52V/1.85A
Power Consumption	3.2 Watts (max. no PD connected)
Power Consumption	According to the actual power consumption of equipment
Temperature	Operation Temperature:0 ~40℃ (32 ~104℉)
Temperature	Storage Temperature: -40 ~70℃(-40 ~158℉)
Humidity	Storage Humidity 5%~90% non-condensing, Operating Humidity 10%~90% non-condensing
Product Dimensions	132mm W x 66mm D x 32mm H
RAM Register Capacity	64K bytes per device
MAC Address List	1K entries per device
Frame Forward Rate	10Mbps Ethernet: 14880pps/Port 100Mbps Ethernet: 14880pps/Port

Notice:

Yellow LED(power) will be light up when micro USB connects to the device.

Green LED(data) never light in any circumstances,two reasons are below,

1.The splitter does not have the function to monitor the data of the network cable.

2.due to the cost problem,the network interface component is from the universal components which own two LEDs on the market.

PoE Splitter Specification:

Compliant with IEEE802.3af
Isolation: 2.5kV
Power Input: DC44~57V
Power Output: DC5V 2.4A
Data&Power INPUT Port: from RJ45 female (Compliant with IEEE802.3af/at PoE)
Data Output Port: RJ45 Male
Power Output Port: Micro USB Power Plug
Data Transfer Rate: 10/100Mbps
Devices will be detected before poe input
Power Pin:support both 1/2(+/-),3/6(-/+) or 4/5(+),7/8(-)
Body size: 80 x 27x 22 mm
DC cable length：165mm
RJ45 Modular Plug cable length：155mm
Weight : 55g

Item Included:

Output 5V 2.4A Active PoE Splitter(Micro USB Power Plug) x4
75Watt 5pots 4PoE Passive PoE switch(DSLRKIT MID4P1U-E250) x1

AC power plug is US or EU type,if you need other type (AU or UK),Please leave a message.