Voltage Supply: 9-12V DC Input
Waveforms: Square, Sine & Triangle
Impedance: 600 Ohm + 10%
Frequency: 1Hz - 1MHz
SINE WAVE
Amplitude: 0 - 3V at 9V DC input
Distortion: Less than 1% (at 1kHz)
Flatness: +0.05dB 1Hz - 100kHz
SQUARE WAVE
Amplitude: 8V (no load) at 9V DC input
Rise Time: Less than 50ns (at 1kHz)
Fall Time: Less than 30ns (at 1kHz)
Symmetry: Less than 5% (at 1kHz)
TRIANGLE WAVE
Amplitude: 0 - 3V at 9V DC input
Linearity: Less than 1% (up to 100kHz) 10mA
2. The Function Generator component parameter table
Note |
label |
type |
parameters |
R1 |
resistor |
1K |
Regardless of the polarity |
R2 |
Adjustable resistance |
B503=50K |
(by screen printing layer) |
R3, R5,R6 |
resistor |
5.1K |
Regardless of the polarity |
R4 |
resistor |
330 |
Regardless of the polarity |
R7 |
Adjustable resistance |
B503=50K |
(by screen printing layer) |
R8 |
Adjustable resistance |
B104=100K |
(by screen printing layer) |
C1, |
Electrolytic capacitor |
100UF |
The positive short feet negative long feet |
C2 |
non-polar capacitors |
104 |
Regardless of the polarity |
C3,C4 |
Electrolytic capacitor |
10UF |
The positive short feet negative long feet |
C5 |
non-polar capacitors |
105 |
Regardless of the polarity |
C6 |
non-polar capacitors |
473 |
Regardless of the polarity |
C7 |
non-polar capacitors |
222 |
Regardless of the polarity |
C8 |
non-polar capacitors |
101 |
Regardless of the polarity |
U1 |
IC |
XR2206 |
(by screen printing layer) |
JK1 |
DC POWER |
|
(by screen printing layer) |
J1 |
2PIN Jumper cap |
XM2.54 |
Regardless of the polarity |
J2 |
2PIN Jumper cap |
XM2.54 |
Regardless of the polarity |
P1 |
Signal wire terminal |
|
(by screen printing layer) |
J3 |
2*5P Jumper cap |
|
|
3.The welding installation considerations, follow these steps:
1. The components are welding the front board, from low to high principles, namely the first low welding components, such as, capacitor, resistor, diode, etc.
2.Welding IC socket, terminal blocks, finally power socket, adjustable potentiometer.
3.The back with a diagonal cutting pliers to cut short the pins as far as possible
4.Debugging steps:
1.After completion of welding on IC, XR2206, pay attention to the direction of IC, insert the might damage the chip!
2. check the IC whether against, such as anti please timely correction.
3. Insert the power supply, power supply for 5.5 * 2.1 port, inside outside is negative polarity. For 9-12 v power supply voltage. The waveform may not be stable for more than 12 v
5.Using the step:
1. J1 jumper cap plug in, SIN/TRI blue terminals output sine wave (note J1, J2 can only insert one of)
2. J2 jumper cap plug in, SIN/TRI blue terminals output triangular wave (note J1, J2 can only insert one of)
3. SQU blue terminals output pulse
4. AMP : Sine wave, triangle wave amplitude adjustment
5. FINE : Frequency fine adjustment
6. Coarse : Frequency of coarse adjustment
6.Schematic diagram of Function GeneratorPackage Included:
1pcs XR2206 Output 1HZ-1MHZ Function Signal Generator DIY Kits Sine Triangle Square
1. PayPal payment accepted only.
2. Items will be shipped to your eBay address. Please make sure it is correct.
3. Payment must be received 4 days after auction ended.
1. Customer satisfaction is our top goal. We believe our items are so outstanding. All products are quality checked. They are new and in good condition when shipped to our customers. We are convinced you will be happy with your Purchase.
2. If product is defective or damage upon arrival, or wrong product shipped, please contact us immediately. Returns accepted within 14 days of delivery date and item must be in original new condition, not worn or altered in any way with attached tags & wrap. Otherwise deal is final. Return shipping must be paid by buyer.
3. Please contact us first if you have any problems/questions/concerns. We will be happy to resolve any issues you may have in a cordial and friendly manner.
4. We appreciate your Postive Feedback, and will do the same in return. DO NOT leave negative feedback without first communication with us. Please allow max 2 business days for us to response.
When you satisfied with our product and services please leave us positive feedback.
If a problem occurs, contact us immediately with any email request. Just contact us using the " Ask the seller a question" link on eBay.