 | ***SPARE PART*** SIMATIC DP, ET 200M INTERFACE IM 153-2 HIGH FEATURE FOR MAX. 12 S7-300 MODULES, WITH REDUNDANCY, TIME STAMPING FIT FOR ISOCHRONE MODE NEW FEATURES: UP TO 12 MODULES / STATION SLAVE INITIATIVE FOR DRIVE ES AND SWITCH ES EXTENDED DATA FOR HART SECONDARY VARIABLES OPERATON OF 64-CHANNEL MODULES 32 SIGNALS / SLOT |
| General information |
| Product type designation | IM 153-2 DP HF |
| Vendor identification (VendorID) | 801Eh |
| Supply voltage |
| Rated value (DC) |
|
| ● 24 V DC | Yes |
| permissible range, lower limit (DC) | 20.4 V |
| permissible range, upper limit (DC) | 28.8 V |
| external protection for power supply lines (recommendation) | 2,5 A |
| Mains buffering |
| ● Mains/voltage failure stored energy time | 5 ms |
| Input current |
| Current consumption, max. | 600 mA |
| Inrush current, typ. | 3 A |
| I²t | 0.1 A²·s |
| Output voltage |
| Rated value (DC) | 5 V |
| Output current |
| for backplane bus (5 V DC), max. | 1.5 A |
| Power loss |
| Power loss, typ. | 5.5 W |
| Address area |
| Addressing volume |
| ● Inputs | 244 byte |
| ● Outputs | 244 byte |
| Hardware configuration |
| Number of modules per DP slave interface, max. | 12 |
| Time stamping |
| Accuracy | 1 ms; 1ms at up to 8 modules; 10ms at up to 12 modules |
| Number of message buffers | 15 |
| Messages per message buffer | 20 |
| Number of stampable digital inputs, max. | 128; Max. 128 signals/station; max. 32 signals/slot |
| Time format | RFC 1119 |
| Time resolution | 0.466 ns |
| Time interval for transmitting the message buffer if a message is present | 1 000 ms |
| Time stamp on signal change | rising / falling edge as signal entering or exiting |
| Interfaces |
| Transmission procedure | RS 485 |
| Interface physics, RS 485 | Yes |
| Interface physics, FOC | No |
| PROFIBUS DP |
| ● Node addresses | 1 to 125 permitted |
| ● automatic detection of transmission rate | Yes |
| ● Output current, max. | 70 mA |
| ● Transmission rate, max. | 12 Mbit/s |
| ● SYNC capability | Yes |
| ● FREEZE capability | Yes |
| ● Direct data exchange (slave-to-slave communication) | Yes; Sender |
| ● Design of electrical connection of PROFIBUS interface | 9-pin sub D |
| 1. Interface |
| DP slave |
| ● GSD file | SI04801.GSG |
| ● automatic baud rate search | Yes |
| Protocols |
| Bus protocol/transmission protocol | PROFIBUS DP to EN 50170 |
| Potential separation |
| Potential separation exists | Yes |
| Isolation |
| Isolation tested with | Isolation voltage 500 V |
| Degree and class of protection |
| IP degree of protection | IP20 |
| Ambient conditions |
| Ambient temperature during operation |
| ● min. | 0 °C |
| ● max. | 60 °C |
| Air pressure acc. to IEC 60068-2-13 |
| ● Installation altitude above sea level, max. | 3 000 m |
| Configuration |
| Configuration software |
| ● STEP 7 | Yes; STEP 7 / COM PROFIBUS / non-Siemens tools via GSD file |
| Dimensions |
| Width | 40 mm |
| Height | 125 mm |
| Depth | 117 mm |
| Weights |
| Weight, approx. | 360 g |
|