This Item has the Integrated Turn Signal LED taillight with Light Smoke lens.

This is a minimalist design recommended for trail riders. The integrated turn signal portion of this design is not street legal in some regions and it is recommended that this only be used in conjunction with side or stalk mount LED turn signals if you intend to use your bike as a dual sport / super moto in heavily traveled areas.

2017 2018 EXC, Six Days XC-W, XC 500, 450, 350, 300, 350, 200, 150, 125 & a few 2016 XC bikes with the new smaller aluminum sub frame.

Euro Style – Number Plate Carrier(Sub Fender) w/ compact SAE/DOT LED Tail / Stop Light /Left and Right turn signals/ License plate illumination.

#1 This unit is specifically designed for 2017 2018 EXC & Six Days Street legal Enduro bikes that come from the factory with front and rear turn signals. This is a bolt on, plug and ride product. New 4 pin Taillight Connector .
*see following notes for XC &XC-W 2 stroke & 4 stroke bikes .

#2 This is a brand new KTM XC-W(OEM) Sub fender with a New compact LED Taillight / Brake light / Left and Right turn signals/ with license plate illumination.

# 3 Very clean, compact and durable and saves 100 grams from the prior years (2012-16) race ready number plate carrier part # 78108016000

#4 Tail Light tucks in neatly under stock KTM EXC Upper Fender.

#5 if you have a non street legal XC and already have the EXC Style upper rear fender piece, then this will bolt on to your bike, yet additional parts will be required to have full functionality of the brake light circuit and turn signals.

#6 Check your fender style, EXC Style has two rear plastic mounting points approximately 10mm diameter and 20mm length that the sub fender mounts – SX style fenders are smooth on the underside.

If you have a 4 stroke or 2 stroke or XC or XC-W ( the ones that have the OEM wiring harness for trail lighting) let me know and we can help you get to where you want to go with your project as we also have tail lights, brake light switches and plug in jumpers available.

Addititional Notes - 2014, 2015 , 2016, 2017 & 2018 KTM EXC & Six Days: 150 , 200, 250, 300, 350 , 450, & 500 :

General installation notes :

I have found it most easily installed by 1st-removing the seat, side panels, and upper fender assembly.
Then Unplug existing taillight wiring and Unplug turn signals.(you must first remove / unbolt the taillight from the number plate carrier to access & Unplug the turn signals & License Plate illumination light see picture).
Unseat /unsnap the existing number plate carrier from number plate .
Pre-Install /snap the number plate carrier onto the sub frame.
Re-Connect wiring and verify function.
Install the upper fender, and install bolts that secure the number plate carrier to the sub frame & upper fender assembly.
Re-install side panels, final check of everything then last thing Re-install seat.

If you have more questions please ask.

Addititional Notes:

Ktm in there wisdom has completely integrated the rear turn signal harness, and original separate license plate light- these JST mini connectors are locates beneath the OEM taillight assembly. The two turn signal connectors are female and the single separate license plate light is male - see picture #9.

They are no longer like the 2007 - 2013 models which had detachable separate Rear Turn Signal harness, that could be replaced in the event of a crash that damaged the rear taillight and or turn signal wiring , now they are continuously wired through out the complete harness.

If you have a damaged rear taillight harness, let me know and I will help out if I can.

The Stock license plate light will need to be abandoned - Just unplug

You may experience the following issues if you convert your turn signals to LED type. LED light bulb turn signals may cause these common and easily corrected issues.

1) If just rear turn signals are converted to LED turn signals then you may experience a more rapid flash rate.

2) If you install LED flashers at both the front and the rear then you must install an LED type relay. Otherwise the turn signals will no longer function. As well it may be necessary to install a left and right hand circuit separator. ( this is not a plug-in play installation should only be installed once one has practiced and mastered the skill of soldering wires together in a butt type splice).

Please message me via eBay messaging if you have any questions.