Super Glue + Super Glue Activator Spray
Product Information
Super Glue 20grm
Medium viscosity formula fills gaps to 0.1mm. For use on perfect fit surfaces where fast set is required.
EVERBUILD STICK2® Superglue GP Bonds non porous surfaces eg most Plastics, Metals, Glass, uPVC, Rubber and EPDM.
Viscosity at 25°c – 100cps. Set time 5 to 15 seconds.
| Chemical Base | Ethyl Cyanoacrylate |
|---|---|
| Packaging | 20g plastic bottle |
| Colour | Transparent |
| Shelf Life | 12 months from date of manufacture when stored as directed |
| Storage Conditions | Store in cool, dry conditions between +5 and +25 ̊C. Ensure good ventilation. Storage outside these parameters will dramatically reduce shelf life. |
| Density | 1.05 g/cm3 |
| Viscosity | 100-120 poise |
| Solids | 100% active |
| Flash Point | >85 °C |
| Impact Strength | 1.8 - 2.0 N/mm2 (steel-steel ASTM 950) |
| Refractive Index | 1.46 (cured adhesive) |
| Hardness | 82 (Rockwell cured adhesive) |
| Specific Resistance | 8 x 1012 Ohm/cm (cured adhesive) |
| Dielectric Const | 3.44 @ 1MHz (cured adhesive) |
| Softening Point | 150 °C |
| Working Temps | -60 to +80°C |
| Setting times | 5-60 seconds (plastic to plastic) 2-20 seconds (rubber to rubber) 10-60 seconds (degreased metal to metal) |
Characteristics / Advantages
- Flash setting formulation, bonds to most non porous surfaces in seconds
- Fills gaps up to 0.1mm
- Single component adhesive
- 100% solvent free
- Economical in use
Substrate Preparation
The surfaces to be glued should be clean, dry and free from dust, grease and other contaminants. Materials should be stored in a warm environment prior to bonding to avoid chilling of the glue line, which leads to extended setting times. Where possible, ensure working environment has a relative humidity of 50% +.
Application Method / Tools
Apply adhesive to one surface only. Press surfaces together and hold for 10 seconds or as indicated above.
Cure speed is rapid so exercise care when aligning.
Limitations
- Ensure surfaces are degreased prior to bonding
- Ensure surfaces are close fitting. This adhesive will not bridge gaps
- Do not use in applications involving constant water immersion
- Do not use on bitumen or tar leaching products
- Adhesion is nevergurenteed as manufacturer cannot know all the uses its products may be put to.
Super Glue Activator Acti-spray 200ml
PVCu Acti-spray is an aerosol applied activator for use with Everbuild Industrial Superglue GP
setting super glue in 10 seconds. Guaranteed not to stain uPVC. Acti-spray is ideal for use on all uPVC and plastics.
| Packaging | 200ml aerosol |
|---|---|
| Appearance / Colour | Clear |
| Shelf Life | 36 months if stored correctly |
| Storage Conditions | Store in cool dry conditions away from direct sunlight between 5 and 25oC.Storage outside these parameters will significantly reduce shelf life. Ensure good ventilation. |
| Density | 1g/cm3 |
| Consumption | 200ml aerosol will cover approx 1m2 |
Characteristics / Advantages -
- Works on all common building surfaces
- Suitable for use with all cyanoacrylate superglues
- Will not cause yellowing of uPVC frames and trim
Application instructions -
Remove cap from canister and apply activator to one of the surfaces to be bonded.
Apply cyanoacrylate adhesive to the other surface.
Bring the parts together ensuring the joint is accurate. Joint sets hard in approximately 5 seconds.
Always replace cap after use to prevent the product drying out.
Limitations -
- Ensure surfaces are degreased prior to bonding
- Do not use on glass
- Do not use in applications involving constant water immersion
- Do not use on bitumen or tar leaching products
- On wooden/porous surfaces, do not use any other cyanoacrylate except Superglue HV.
- These products are thinner and the soak in will give poor bond strength
- It is the user’s responsibility to determine suitability for use.
Open Monday - Thursday 7.30am - 4.30pm.
Friday 7.30am - 1.30pm.
