Water Sensor Mobile APP Remote Water Level Alarm Switch Fuel Tank Flow Detector
1. Using high-quality materials, the quality is guaranteed
2. Real-time synchronous feedback of remote output status and water level
3. It can run independently without WIFI, and realize the function of single-machine control of water level
4. The on-off of one output can be controlled remotely or manually on site (when the set water level value is not reached)
5. It can control drainage with high opening and low closing, or control water replenishment with low opening and high closing, or select time-limited control mode
6. Remote upper and lower water level alarm APP push function
7. APP can display the current water level, start water level, stop water level, upper and lower limit alarm water level
8. Two outputs, one water level control, one anti-dry function
9. The main account can share the device with others, and the device can only be added under one main account (note that the alarm can only be realized if the device and the mobile phone are both online. Without the network, it is like the mobile phone can’t make a call without a signal!)
2. Real-time synchronous feedback of remote output status and water level
3. It can run independently without WIFI, and realize the function of single-machine control of water level
4. The on-off of one output can be controlled remotely or manually on site (when the set water level value is not reached)
5. It can control drainage with high opening and low closing, or control water replenishment with low opening and high closing, or select time-limited control mode
6. Remote upper and lower water level alarm APP push function
7. APP can display the current water level, start water level, stop water level, upper and lower limit alarm water level
8. Two outputs, one water level control, one anti-dry function
9. The main account can share the device with others, and the device can only be added under one main account (note that the alarm can only be realized if the device and the mobile phone are both online. Without the network, it is like the mobile phone can’t make a call without a signal!)
Specification:
Model: YF-S201
Interface size: 4 points (G1/2)
Operating voltage range: DC5 ~ 15V
Inner/Outer Diameter: 10.9mm/20mm
Thread length: 14.5mm12.5mm
Material: Nylon
Water pressure resistance: ≤1.75MPa
Output pulse high level: >DC4.7V (input voltage DC5V)
Output pulse low level: <DC0.5V (input voltage DC5V)
Insulation resistance: >100MQ
Flow range: 1～30L\MIN
Airtightness: Close each hole, add 1.7Mpa water pressure test for 1 minute without leakage and deformation
Flow pulse characteristics: F= (7.5*Q) error≤3%
Appearance size: 89*55*44mm
Installation method and size: standard 35MM rail installation
Working power and power consumption: AC220V; <2W
Water level display: five-level water level display: 0%, 25%, 50%, 75%, 100%
Water level control range: full water level: 25%, 50%, 75%, 100% make-up water level: 25%, 50%, 75%, 100%
Time limit range: 0-720 minutes, need to be set on the APP, step by 5 minutes to set
Relay life: on and off 100,000 times
Operating environment: -10℃~50℃
Wireless standard: WIFI2.4GHZ B/G/N
Parameter memory: long-term memory of setting parameters when power off, can run offline
Model: YF-S201
Interface size: 4 points (G1/2)
Operating voltage range: DC5 ~ 15V
Inner/Outer Diameter: 10.9mm/20mm
Thread length: 14.5mm12.5mm
Material: Nylon
Water pressure resistance: ≤1.75MPa
Output pulse high level: >DC4.7V (input voltage DC5V)
Output pulse low level: <DC0.5V (input voltage DC5V)
Insulation resistance: >100MQ
Flow range: 1～30L\MIN
Airtightness: Close each hole, add 1.7Mpa water pressure test for 1 minute without leakage and deformation
Flow pulse characteristics: F= (7.5*Q) error≤3%
Appearance size: 89*55*44mm
Installation method and size: standard 35MM rail installation
Working power and power consumption: AC220V; <2W
Water level display: five-level water level display: 0%, 25%, 50%, 75%, 100%
Water level control range: full water level: 25%, 50%, 75%, 100% make-up water level: 25%, 50%, 75%, 100%
Time limit range: 0-720 minutes, need to be set on the APP, step by 5 minutes to set
Relay life: on and off 100,000 times
Operating environment: -10℃~50℃
Wireless standard: WIFI2.4GHZ B/G/N
Parameter memory: long-term memory of setting parameters when power off, can run offline
Configuration process
Installation preparation:
Search for "Tuya Smart" and install the APP.
After installing the APP, please use your mobile phone or email to register an account.
Note that please use the system default font, otherwise it will display confusion
Installation preparation:
Search for "Tuya Smart" and install the APP.
After installing the APP, please use your mobile phone or email to register an account.
Note that please use the system default font, otherwise it will display confusion
Mobile APP adding device process
1. Connect the wires according to the wiring diagram. After the first power-on, wait for a few seconds, the indicator light 1 flashes quickly, and the device enters the WIFI configuration mode by default.
Note: If the device has been added to the APP and needs to be reconfigured, press and hold the configuration button in the working state until the indicator lights 1 and 2 flash at the same time, and then release the button. At this time, the device enters the smart configuration mode. The router is not compatible, at this time, you can press and hold the configuration button again, the indicator lights 1 and 2 flash slowly, and then enter the compatibility mode configuration.
2. Open the APP, and click the "+" icon in the upper right corner to select any device.
3. Click "Confirm the indicator light is flashing quickly" on the APP
4. Prompt to select a wifi that can access the Internet normally and enter the password. After confirming the password and entering it correctly, click "OK".
4.1 The device uses 2.4G wifi communication protocol, and does not support 5G network for the time being.
4.2 If the network is set to hide or filter the MAC address, please ask the network administrator to enter the background to modify the settings, and then add the device.
5. The APP automatically starts to configure, and the device is added successfully when the progress bar is reached.
6. After adding successfully, you can rename the device.
Note: After the addition is successful, the device will be automatically deleted from the current APP if it is reconfigured.
1. Connect the wires according to the wiring diagram. After the first power-on, wait for a few seconds, the indicator light 1 flashes quickly, and the device enters the WIFI configuration mode by default.
Note: If the device has been added to the APP and needs to be reconfigured, press and hold the configuration button in the working state until the indicator lights 1 and 2 flash at the same time, and then release the button. At this time, the device enters the smart configuration mode. The router is not compatible, at this time, you can press and hold the configuration button again, the indicator lights 1 and 2 flash slowly, and then enter the compatibility mode configuration.
2. Open the APP, and click the "+" icon in the upper right corner to select any device.
3. Click "Confirm the indicator light is flashing quickly" on the APP
4. Prompt to select a wifi that can access the Internet normally and enter the password. After confirming the password and entering it correctly, click "OK".
4.1 The device uses 2.4G wifi communication protocol, and does not support 5G network for the time being.
4.2 If the network is set to hide or filter the MAC address, please ask the network administrator to enter the background to modify the settings, and then add the device.
5. The APP automatically starts to configure, and the device is added successfully when the progress bar is reached.
6. After adding successfully, you can rename the device.
Note: After the addition is successful, the device will be automatically deleted from the current APP if it is reconfigured.
Package List:
1 x Water Level Controller
5 x Water Level Electrodes
1 x Water Level Controller
5 x Water Level Electrodes
1.We accept PayPal payment ONLY, and must be received within 5 days from the date of purchase.
2. It is easy and safe for you to pay by credit cards, debit cards, bank transfers and PayPal account balances. 3.Buyers are responsible for import duties,custom fees and taxes, if any, please check your country.
1.We believe our items are so outstanding. We are convinced you will be happy with your Purchase.
2. If you do not satisfy with our items. Please simply return to us within 30 Days in original condition. Just pay for the returned postage. Then we can issue full refund or resend the item to you after the returned item arrived at our warehouse.
3. Please include your eBay ID and item number with any email requests.
2. If you do not satisfy with our items. Please simply return to us within 30 Days in original condition. Just pay for the returned postage. Then we can issue full refund or resend the item to you after the returned item arrived at our warehouse.
3. Please include your eBay ID and item number with any email requests.
1.We only ship to the confirmed address provided by eBay. please make sure your ebay address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand.
2.Orders will be processed instantly and dispatched within 1-2 business days except hoilday, so we do NOT accept any email/message note after you place orders.
3.All package need to wait 30 days,Please take care it.Less than 30 days,we can't take a refund.
1.We greatly appreciate your POSITIVE feedback. Please do NOT leave negative feedback without asking for help.
2.Please DON'T leave negative or neutral feedback if you haven't received item in 30 days, because we have mentioned the shipping time repeatedly
1. If you have any questions, please feel free to email our service specialists.
2.Just contact us using the " Ask the seller a question" link on eBay.
3.Our aim is to provide Top Level Customer Service, normally so we will try our best to solve any problem.
2.Just contact us using the " Ask the seller a question" link on eBay.
3.Our aim is to provide Top Level Customer Service, normally so we will try our best to solve any problem.