Ship from USA Warehouse fast shipping service to US Customers
Parcel:
3 x 23HS2430B Nema23 stepper motor (Dual Shaft) 112mm,425oz-in,2.8N.m,3.0A
3 x CW5045 stepper motor driver 24-50V,4.5A,256microstep
1 x 400W 36V/9.7A switching power supply
1 x 5 Axis breakout board V5 type
1 x DB25 parallel cable
1 x USB cable
User manual & mach3 software will send via email.
Descriptions:
5 axis breakout board
Description:
- It can most connection 5pcs driver and control 5pcs motor in the same time
- It is with 4-wire limit switch to insure our safty movement
- It is with relay port to contro the cnc spindle
- Working voltage is 5VDC and support with MACH3,EMC2,KCAM4 software
- Size:9x5.7cm
25-pin parallel port control is defined as follows:
DB25 control pin (PIN)
The pin of the drive board
Comment
1
STEPB
B(Fifth axis)pulse signal
2
STEPX
X(First axis) pulse signal
3
DIRX
X(First axis) direction of the signal
4
STEPY
Y(Secondaxis)pulse signal
5
DIRY
Y(Second axis)direction of the signal
6
STEPZ
Z(Third axis) pulse signal
7
DIRZ
Z(Third axis) direction of the signal
8
STEPA
A(Fourth axis) pulse signal
9
DIRA
A(Fourth axis) direction of the signal
10
LIMIT-1
Limit input interface 1
11
LIMIT-2
Limit input interface 2
12
LIMIT-3
Limit input interface 3
13
LIMIT-4
Limit input interface 4
14
DIRB
B(Fifth axis) direction of the signal
15
Vacant
16
RLY
Relay control
17
EN
All axis enable
18-25
GND
GND
Remark:this 5 axis breakout board can connction with many driver type as a CNC 3/4/5 axis driver controller kit,pls if you intresting pls contact us!
2. CW5045 high microstep stepper motor driver
Description:
- Input voltage: 24-50VDC
- Output current: 1.3,1.8,2.3,2.7,3.2,3.7,4.2,4.5A
- Mircostepping: 1(1.8°),1/2,1/4,1/8,1/16,1/32,1/64,1/128,1/256;
- 1/5,1/10,1/25,1/50,1/125,1/250
- Protect form: Overheated protect, lock automatic half current ,error connect protect
- Working environment: Temperature-15-40deg Humidity<90%
- It is fit for NEMA17-23 two and four phase stepper motors whose current is small than 4.5A,
Switch Choice: (ON=0,OFF=1)
1.Microstepping choice:
| SW5 |
0 |
0 |
0 |
0 |
0 |
0 |
0 |
0 |
1 |
1 |
1 |
1 |
1 |
1 |
| SW6 |
0 |
1 |
0 |
1 |
0 |
1 |
0 |
1 |
0 |
1 |
0 |
1 |
0 |
1 |
| SW7 |
0 |
0 |
1 |
1 |
0 |
0 |
1 |
1 |
0 |
0 |
1 |
1 |
0 |
0 |
| SW8 |
0 |
0 |
0 |
0 |
1 |
1 |
1 |
1 |
0 |
0 |
0 |
0 |
1 |
1 |
| Micro |
1/2 |
1/4 |
1/8 |
1/16 |
1/32 |
1/64 |
1/128 |
1/256 |
1/5 |
1/10 |
1/25 |
1/50 |
1/125 |
1/250 |
2.Current choice:
| SW1 |
0 |
1 |
0 |
1 |
0 |
1 |
0 |
1 |
| SW2 |
0 |
0 |
1 |
1 |
0 |
0 |
1 |
1 |
| SW3 |
0 |
0 |
0 |
0 |
1 |
1 |
1 |
1 |
| Current(A) |
1.3 |
1.8 |
2.3 |
2.7 |
3.2 |
3.7 |
4.2 |
4.5 |
3.Full current or half current choice: SW4:0=Full current; 1=half current
We also can offer customer NEMA17-23 stepper motors,so if you need pls contact us.
Application Notice:
- To avoid use in the oil contamination,dust and corrosive gas environment
- To lay it in a place with good ventilation
- Pls note the connection with right power(+ and -) to avoid broken the driver
- Pls test it when confirm the connection is right.
2. Stepper Motor
Wirings:
4 Wires
- Stepper motor's red wire connect to driver's A+ port
- Stepper motor's green wire connect to driver's A- port
- Stepper motor's yellow wire connect to driver's B+ port
- Stepper motor's blue wire connect to driver's B- port
General Specification:
- Step angle accuracy:+ - 5%(full step,not load)
- Resistance accuracy: + - 10%
- Inductance accuracy:+ - 20%
- Temperature rise: 80deg Max(rated current,2 phase on)
- Ambient temperature: 20deg-50deg
23HS2430B Nema23 Stepper Motor
Electrical Specification:
* Model Number: 23HS2430B
* Motor Type: Hybrid Stepper
* Step Angle: 1.8 deg.
* Holding Torque: 2.8Nm (425oz.in)
* Phase Resistance: 1.6ohms
* Rated Current/phase: 3A
* Inductance: 6.8mH+/-20%(1KHz)
Physical Specification:
- Frame Size: 57 x 57 x 112 mm
- Body Length: 112mm
- Number of Leads: 4
- Weight: 1.8kg
- Front shaft 8mm dia and 21mm length,back shaft 8mm dia and 11mm length
This is the high torque model for Nema 23 stepper motor, it with 1.8 degree.
rated current is 3A, allowing for a holding torque of 280Ncm(425oz.in).
Advantages
- Our motor is made of solid and durable metal. The perfect combination of rubber and rotor makes the internal structure more stable, and also reduces the vibration and noise when the engine runs.
- The motor runs more quietly, with a high torque of 425oz in. The coil uses pure copper enamelled wire to ensure that long-term operation will not lead to excessive engine temperature.
- The rotor surface is coated with high-quality epoxy resin adhesive to isolate the adsorbed burrs on the rotor surface, more stable magnetic field and longer service life of motor.
Usage or Application
This products are widely used in engraving machine, printer, medical equipment,embroidery machine, stage lighting, textile automation, printing,packaging and other industries automation equipment.
3.Switching power supply
400W,Input:100-120VAC or 200-240VAC,50/60Hz,Output:36v/9.7 A,single output switching power supply
Shipping
Please open the package and check if there are some damages before sign,if there are some damages,please do not sign and contact us immediately.
Problem&Feedback
Please give us the opportunityto resolve any problem when you have,we concern your problem and we will try our best to resolve it.
Pls contact us before you want to leave any negative feedback.
Refund
Any reason required for all refund. Item must be in it's original condition and no physical damage,buyer responsible for all shipping cost.
When you have the parcel,and not satisfied the goods or it is other problem like as broken,pls tell us the detail reason and provide the photos.