Constant Temperature PTC Heating Element Thermostat Heater Plate Model for choice: 5V 60℃ /2-4W Specifications: Features: Reminder: It can only be boiled dry, can not be opened, can not be tapped, can not be soaked in water. For example, 12V/60°C means that the surface of the heating element with a voltage of 12 volts is dry-fired at a constant temperature of about 60°C. When the temperature rises, it is 8 watts. After the heating plate is kept at a constant temperature, the resistance becomes larger, the current becomes smaller, and the power is reduced to about 2 watts. Product Advantages: About Power: Use: Note:
12V 60℃ /2-8W
12V 140℃ /4-12W
24V 60℃ /4-20W
24V 140℃ /10-40W
220V 70℃ /2-5W
220V 150℃ /5-12W
220V 250℃ /9-25W
5V 50℃ /2-3W
12V 230℃ /12-40W
Material: Aluminum
Size: 25 * 20 * 5 mm
Lead length: 70mm
Power: 2~ 40W
Safety, surface insulation
It can be a long dry
Heating the solid and gas
Type PTC aluminum shell heater simple structure
Easy installation, automatic thermostat,
It does not require temperature control, safety, long life
PTFE high temperature resistant wire, the lead length is greater than 70mm, the surface is constant temperature, the error is ±10 degrees
Working principle: The internal heating element of the PTC heater is a positive temperature coefficient thermistor, and its resistance value shows a step increase with the increase of the temperature of the PTC thermistor body. The higher the temperature, the greater the resistance value.
Dry burning, energy saving, long life, no open flame, suitable for low-power antipyretic preheating and dehumidification of micro equipment.
Power Selection:
1. It can be directly connected to the rated voltage, both AC and DC, without positive and negative poles.
2. Take the 12V heating plate as an example, it can be connected to AC and DC 12V, and the power supply current must be greater than the maximum heating current of the heating plate, otherwise the heating plate cannot be brought.
1. After the PTC heating element is energized, the power is reduced from small to large and then to small, and finally stabilized. The stable power is directly related to the heat dissipation, the heat dissipation is fast, and the power consumption is also large. Our target is the maximum dissipation power, and the actual power used is less than the maximum dissipation power.
2. It is strictly forbidden to use it in corrosive, flammable and explosive occasions, it is strictly forbidden to put it into water, it is strictly forbidden to knock it, and it is strictly forbidden to open holes.
3. Multiple heating pads with the same voltage can be connected in parallel, and multiple heating pads can be installed side by side. The heating pads cannot be installed overlapping each other, otherwise the heat will be offset.
4. Multiple heating pieces should be used together in parallel. The more heating pieces, the higher the power.
5. The reduction of the power supply voltage will make the heating time longer and the power smaller, but the temperature is basically constant (the temperature drops slightly).
1. Battery, security, medical, scientific research, industrial motor, aerospace and other electronic and electrical low-power heating, preheating, dehumidification and heat preservation.
2. It is widely used, such as electric mosquito coil heater, shoe warmer heater, incense burner heater, fan heater heater, electric cup heater, water dispenser heater, coffee maker heater, yogurt maker heater, auto parts Insulation, diesel alcohol heating, instrument heating and dehumidification, solenoid valve antifreeze, power distribution cabinet dehumidification and dehumidification, constant temperature preheating of electronic components, portable heating elements, and many other uses that can be developed.
The temperature marked here is the maximum temperature limit of the surface temperature of the heating piece in the state of empty burning, and this temperature does not represent the temperature during use. The operating temperature is controlled by the environment and on-site heat absorption. The surface temperature limit temperature and the operating temperature of the air-burning surface are two completely different temperatures. Please explain this misunderstanding.