Description
PortaPack H2 + HackRF + 5pcs Antennas + Data Cable SDR Software Defined Radio 1MHz-6GHz Assembled
Hardware Configuration:
-3.2 inches TFT 240 * 320 screen
-Navigation switch
-Audio output
-Microphone input
-DC 2.1 interface
-4-layer gold plate
-ROSH process (exported to Europe and America)
Add a PortaPack to your software defined radio HackRF, and leave your laptop behind! The PortaPack connects to your HackRF and adds an LCD touchscreen, navigation controls, headphone jack, real-time clock, micro SD card slot.
Just add a USB battery, and you're ready to explore radio spectrum wherever you are. The PortaPack firmware works with the fast ARM processors in your HackRF. No computer is needed (except for firmware reprogramming).
Functions:
-3.2 inches, 240 x 320 RGB LCD with resistive touch panel.
-Four-way arrow buttons, rotary wheel and select button.
-Coin battery to preserve settings and date / time.
-Micro SD card slot for data and storage code
-SSB, AM, narrowband FM, broadband FM audio reception, with cascade spectrum.
-Broadband (18MHz) spectrum and cascade analysis.
-Monitoring of boat (AIS), automobile (TPMS), E utility counter transponder (ITRON ERT).
-HackRF mode runs HackRF firmware for use with the SDR host computer software.
-Calibration PPM for more accurate tuning.
-Sleep mode saves energy by turning off the display only.
Features:
-Your HackRF will continue to work with the computer-based SDR software when you put the PortaPack in "HackRF mode".
-PortaPack is only compatible with the HackRF Uno. It is not compatible with the first HackRF Jawbreaker design. If you have an RF shield installed on your HackRF, the PortaPack should be fine. Compatibility with the HackRF Blu is experimental. A proprietary Blu reported good results with less interference between the audio capacitors PortaPack and the mechanical header band. If your Blue HackRF doesn't have a header band installed, you should have no mechanical problems.
-PortaPack requires an external battery. Any USB-connected battery should work, although they vary widely in quality and poorly designed batteries can inject noise voltage regulator into the radio.
-PortaPack and HackRF of Un will not replace your handheld ham radio receiver. Reception sensitivity varies from band to band, but will not perform as well as a real ham radio receive
Package List:
-1 x SRD Radio (PortaPack H2+HackRF)
-1 x Data Cable
-5 x Antennas
Note:
-The product is assembled.
-The battery is not included.
Hardware Configuration:
-3.2 inches TFT 240 * 320 screen
-Navigation switch
-Audio output
-Microphone input
-DC 2.1 interface
-4-layer gold plate
-ROSH process (exported to Europe and America)
Add a PortaPack to your software defined radio HackRF, and leave your laptop behind! The PortaPack connects to your HackRF and adds an LCD touchscreen, navigation controls, headphone jack, real-time clock, micro SD card slot.
Just add a USB battery, and you're ready to explore radio spectrum wherever you are. The PortaPack firmware works with the fast ARM processors in your HackRF. No computer is needed (except for firmware reprogramming).
Functions:
-3.2 inches, 240 x 320 RGB LCD with resistive touch panel.
-Four-way arrow buttons, rotary wheel and select button.
-Coin battery to preserve settings and date / time.
-Micro SD card slot for data and storage code
-SSB, AM, narrowband FM, broadband FM audio reception, with cascade spectrum.
-Broadband (18MHz) spectrum and cascade analysis.
-Monitoring of boat (AIS), automobile (TPMS), E utility counter transponder (ITRON ERT).
-HackRF mode runs HackRF firmware for use with the SDR host computer software.
-Calibration PPM for more accurate tuning.
-Sleep mode saves energy by turning off the display only.
Features:
-Your HackRF will continue to work with the computer-based SDR software when you put the PortaPack in "HackRF mode".
-PortaPack is only compatible with the HackRF Uno. It is not compatible with the first HackRF Jawbreaker design. If you have an RF shield installed on your HackRF, the PortaPack should be fine. Compatibility with the HackRF Blu is experimental. A proprietary Blu reported good results with less interference between the audio capacitors PortaPack and the mechanical header band. If your Blue HackRF doesn't have a header band installed, you should have no mechanical problems.
-PortaPack requires an external battery. Any USB-connected battery should work, although they vary widely in quality and poorly designed batteries can inject noise voltage regulator into the radio.
-PortaPack and HackRF of Un will not replace your handheld ham radio receiver. Reception sensitivity varies from band to band, but will not perform as well as a real ham radio receive
Package List:
-1 x SRD Radio (PortaPack H2+HackRF)
-1 x Data Cable
-5 x Antennas
Note:
-The product is assembled.
-The battery is not included.
PortaPack H2 + HackRF + 2pcs Antennas + Data Cable SDR Software Defined Radio 1MHz-6GHz Assembled
Hardware Configuration:
-3.2 inches TFT 240 * 320 screen
-Navigation switch
-Audio output
-Microphone input
-DC 2.1 interface
-4-layer gold plate
-ROSH process (exported to Europe and America)
Add a PortaPack to your software defined radio HackRF, and leave your laptop behind! The PortaPack connects to your HackRF and adds an LCD touchscreen, navigation controls, headphone jack, real-time clock, micro SD card slot.
Just add a USB battery, and you're ready to explore radio spectrum wherever you are. The PortaPack firmware works with the fast ARM processors in your HackRF. No computer is needed (except for firmware reprogramming).
Functions:
-3.2 inches, 240 x 320 RGB LCD with resistive touch panel.
-Four-way arrow buttons, rotary wheel and select button.
-Coin battery to preserve settings and date / time.
-Micro SD card slot for data and storage code
-SSB, AM, narrowband FM, broadband FM audio reception, with cascade spectrum.
-Broadband (18MHz) spectrum and cascade analysis.
-Monitoring of boat (AIS), automobile (TPMS), E utility counter transponder (ITRON ERT).
-HackRF mode runs HackRF firmware for use with the SDR host computer software.
-Calibration PPM for more accurate tuning.
-Sleep mode saves energy by turning off the display only.
Features:
-Your HackRF will continue to work with the computer-based SDR software when you put the PortaPack in "HackRF mode".
-PortaPack is only compatible with the HackRF Uno. It is not compatible with the first HackRF Jawbreaker design. If you have an RF shield installed on your HackRF, the PortaPack should be fine. Compatibility with the HackRF Blu is experimental. A proprietary Blu reported good results with less interference between the audio capacitors PortaPack and the mechanical header band. If your Blue HackRF doesn't have a header band installed, you should have no mechanical problems.
-PortaPack requires an external battery. Any USB-connected battery should work, although they vary widely in quality and poorly designed batteries can inject noise voltage regulator into the radio.
-PortaPack and HackRF of Un will not replace your handheld ham radio receiver. Reception sensitivity varies from band to band, but will not perform as well as a real ham radio receive
Package List:
-1 x SRD Radio (PortaPack H2+HackRF)
-1 x Data Cable
-2 x Antennas
Note:
-The product is assembled.
-The battery is not included.
PortaPack H2 + HackRF + Antenna + Data Cable Kit SDR Software Defined Radio 1MHz-6GHz Assembled
Hardware Configuration:
-3.2 inches TFT 240 * 320 screen
-Navigation switch
-Audio output
-Microphone input
-DC 2.1 interface
-4-layer gold plate
-ROSH process (exported to Europe and America)
Add a PortaPack to your software defined radio HackRF, and leave your laptop behind! The PortaPack connects to your HackRF and adds an LCD touchscreen, navigation controls, headphone jack, real-time clock, micro SD card slot.
Just add a USB battery, and you're ready to explore radio spectrum wherever you are. The PortaPack firmware works with the fast ARM processors in your HackRF. No computer is needed (except for firmware reprogramming).
Functions:
-3.2 inches, 240 x 320 RGB LCD with resistive touch panel.
-Four-way arrow buttons, rotary wheel and select button.
-Coin battery to preserve settings and date / time.
-Micro SD card slot for data and storage code
-SSB, AM, narrowband FM, broadband FM audio reception, with cascade spectrum.
-Broadband (18MHz) spectrum and cascade analysis.
-Monitoring of boat (AIS), automobile (TPMS), E utility counter transponder (ITRON ERT).
-HackRF mode runs HackRF firmware for use with the SDR host computer software.
-Calibration PPM for more accurate tuning.
-Sleep mode saves energy by turning off the display only.
Features:
-Your HackRF will continue to work with the computer-based SDR software when you put the PortaPack in "HackRF mode".
-PortaPack is only compatible with the HackRF Uno. It is not compatible with the first HackRF Jawbreaker design. If you have an RF shield installed on your HackRF, the PortaPack should be fine. Compatibility with the HackRF Blu is experimental. A proprietary Blu reported good results with less interference between the audio capacitors PortaPack and the mechanical header band. If your Blue HackRF doesn't have a header band installed, you should have no mechanical problems.
-PortaPack requires an external battery. Any USB-connected battery should work, although they vary widely in quality and poorly designed batteries can inject noise voltage regulator into the radio.
-PortaPack and HackRF of Un will not replace your handheld ham radio receiver. Reception sensitivity varies from band to band, but will not perform as well as a real ham radio receive
Package List:
-1 x SRD Radio (PortaPack H2+HackRF)
-1 x Data Cable
-1 x Antenna
Note:
-The product is assembled.
-The battery is not included.
Hardware Configuration:
-3.2 inches TFT 240 * 320 screen
-Navigation switch
-Audio output
-Microphone input
-DC 2.1 interface
-4-layer gold plate
-ROSH process (exported to Europe and America)
Add a PortaPack to your software defined radio HackRF, and leave your laptop behind! The PortaPack connects to your HackRF and adds an LCD touchscreen, navigation controls, headphone jack, real-time clock, micro SD card slot.
Just add a USB battery, and you're ready to explore radio spectrum wherever you are. The PortaPack firmware works with the fast ARM processors in your HackRF. No computer is needed (except for firmware reprogramming).
Functions:
-3.2 inches, 240 x 320 RGB LCD with resistive touch panel.
-Four-way arrow buttons, rotary wheel and select button.
-Coin battery to preserve settings and date / time.
-Micro SD card slot for data and storage code
-SSB, AM, narrowband FM, broadband FM audio reception, with cascade spectrum.
-Broadband (18MHz) spectrum and cascade analysis.
-Monitoring of boat (AIS), automobile (TPMS), E utility counter transponder (ITRON ERT).
-HackRF mode runs HackRF firmware for use with the SDR host computer software.
-Calibration PPM for more accurate tuning.
-Sleep mode saves energy by turning off the display only.
Features:
-Your HackRF will continue to work with the computer-based SDR software when you put the PortaPack in "HackRF mode".
-PortaPack is only compatible with the HackRF Uno. It is not compatible with the first HackRF Jawbreaker design. If you have an RF shield installed on your HackRF, the PortaPack should be fine. Compatibility with the HackRF Blu is experimental. A proprietary Blu reported good results with less interference between the audio capacitors PortaPack and the mechanical header band. If your Blue HackRF doesn't have a header band installed, you should have no mechanical problems.
-PortaPack requires an external battery. Any USB-connected battery should work, although they vary widely in quality and poorly designed batteries can inject noise voltage regulator into the radio.
-PortaPack and HackRF of Un will not replace your handheld ham radio receiver. Reception sensitivity varies from band to band, but will not perform as well as a real ham radio receive
Package List:
-1 x SRD Radio (PortaPack H2+HackRF)
-1 x Data Cable
-1 x Antenna
Note:
-The product is assembled.
-The battery is not included.
PortaPack For HackRF One SDR Receiver Transmitter Ham Radio w/ 3pcs Antennas + Data Cable Assembled
Description:
-The official firmware created for the PortaPack has several decoders and transmitters built into it, but the third party 'Havoc' firmware is really what you'll want to use with it since it contains many more decoders and transmit options.
-You can fully unleash the power of the Portapack as this comes with Havoc Firmware Installed!
Progress of Work:
1. We have completed the program validation prototype.
2. The latest 2017.5 month documents are based on improvements.
Collect and Replay:
One of the best things about the PortaPack is that it makes acquisition and replay of wireless signals like those from ISM band remote controls extremely easy. To create an acquisition you just need to enter the "Acquistion" menu, set the frequency of the remote key, press the red 'R' Record button and then press the key on the remote. Then stop the recording to save it to the SD Card.
Now you can go into the Replay menu, select the file that you just recorded and hit play. The exact same signal will be transmitted over the air, effectively replacing your remote key.
Microphone TX:
Using the 3.5mm audio jack the Portapack can also be used as a standard Push to Talk or voice activated walkie talkie radio. With a microphone plugged into the audio jack simply hold down the right button to push to talk. If required you can also enable multiple CTCSS tone options, as well as tones that look like they enable transmission to wireless headphones
Other Transmitters:
There are generic OOK transmitter which can be programmed with custom data. This mode might be useful for experimenting with simple keyfobs, or things like home automatation switches.There are numerous transmit modes implemented that are questionable in most countries and could get you into huge trouble. These transmitters are purely to be used for internal testing with a faraday cage!
Receivers:
By connecting speakers to the Portapack's 3.5mm audio jack you can easily listen in on standard NFM and WFM audio signals. ADS-B reception can be easily enabled on the PortaPack by selecting the inductor and lightning symbol on the top right. With the bias tee enabled you can receive aircraft.
Hardware Configuration:
1.TFT240*320 screen (model: ER-TFT024-3)
2. navigation switch (TSWB3NCB222)
3. audio output
4. microphone input
5. DC2.1 interface
6. 4 layer gold plate
7. ROSH process (exported to Europe and America)
The latest version is updated with the latest documents in 2017.5 month
Add a PortaPack to your HackRF One software-defined radio, and leave your laptop behind! The PortaPack attaches to your HackRF and adds a touchscreen LCD, navigation controls, headphone jack, real-time clock, micro SD card slot,
Just add a USB battery, and you're ready to explore radio spectrum wherever you are. The PortaPack firmware runs on the fast ARM processors in your HackRF. No computer is necessary (except for reprogramming firmware).
HAVOC Features:
- IQ file replay
- Microphone FM transmit with CTCSS
- CTCSS decoder
- Frequency manager (save & load from SD card, with categories and notes)
- File manager
- "Soundboard" wave file player (put 8-bit mono files in SD card /wav directory)
- ADS-B receiver with map view
- SSTV transmitter
- Fully configurable transmit signals
- POCSAG transmitter
- POCSAG receiver/decoder
- Morse transmitter (FM tone and CW)
- OOK transmitter for common remote encoders (PT2262, doorbells, remote outlets, some garage doors, ...)
- RDS (Radio Data System) PSN, RadioText and Time groups transmitter
- Meteorological radiosonde receiver for M10 and M2K2...
- AFSK receiver
- AFSK transmitter (Bell202...)
- Nuoptix DTMF sync transmitter
- TouchTunes jukebox universal remote
- LCR (Language de Commande Routier) message generator
- Street lighting control transmitter (CCIR tones)
- "Play Dead" in case of emergency
- Fully configurable RF signal generator
- RSSI audio output as pitch (for direction finding)
Specifications:
- 2.4 inch, 240 x 320 RGB LCD with resistive touch panel.
- Four-way arrow keys, rotary jog wheel, and select button.
- Preserving settings and date/time.
- Micro SD card slot for data and code storage
Some features demonstrated in 2016 February 22 firmware video:
- SSB, AM, narrowband FM, wideband FM audio reception, with spectrum waterfall.
- Wideband (18MHz) spectrum analysis and waterfall.
- Monitoring of boat (AIS), automobile (TPMS), and utility meter transponders (ITRON ERT).
- HackRF mode runs HackRF firmware for use with host computer SDR software.
- PPM calibration for more accurate tuning.
- Sleep mode saves power by turning off just the display.
You may also find the Furrtek HAVOC firmware very interesting!
Your HackRF will continue to function with computer-based SDR software, when you put the PortaPack into "HackRF Mode".
PortaPack is compatible only with the HackRF One. It is not compatible with the earlier HackRF Jawbreaker design. If you have an RF shield installed on your HackRF, the PortaPack should fit just fine. Compatibility with the HackRF Blue is experimental. One Blue owner has reported good results with minor mechanical interference between the PortaPack audio capacitors and the baseband header. If your HackRF Blue does not have a baseband header installed, you should have no mechanical problems.
PortaPack requires an external battery. Any USB-connected battery should work, though they vary widely in quality and poorly-designed batteries may inject voltage regulator noise into the radio.
The PortaPack and HackRF One will not replace your handheld ham radio receiver. Receive sensitivity varies from band to band, but will not perform as well as a true ham radio receive
Package List:
-1 x PortaPack
-1 x HackRF One
-3 x Antennas
-1 x Data Cable
-1 x Aluminum Alloy Case
Note: The PortaPack is assembled.
Description:
-The official firmware created for the PortaPack has several decoders and transmitters built into it, but the third party 'Havoc' firmware is really what you'll want to use with it since it contains many more decoders and transmit options.
-You can fully unleash the power of the Portapack as this comes with Havoc Firmware Installed!
Progress of Work:
1. We have completed the program validation prototype.
2. The latest 2017.5 month documents are based on improvements.
Collect and Replay:
One of the best things about the PortaPack is that it makes acquisition and replay of wireless signals like those from ISM band remote controls extremely easy. To create an acquisition you just need to enter the "Acquistion" menu, set the frequency of the remote key, press the red 'R' Record button and then press the key on the remote. Then stop the recording to save it to the SD Card.
Now you can go into the Replay menu, select the file that you just recorded and hit play. The exact same signal will be transmitted over the air, effectively replacing your remote key.
Microphone TX:
Using the 3.5mm audio jack the Portapack can also be used as a standard Push to Talk or voice activated walkie talkie radio. With a microphone plugged into the audio jack simply hold down the right button to push to talk. If required you can also enable multiple CTCSS tone options, as well as tones that look like they enable transmission to wireless headphones
Other Transmitters:
There are generic OOK transmitter which can be programmed with custom data. This mode might be useful for experimenting with simple keyfobs, or things like home automatation switches.There are numerous transmit modes implemented that are questionable in most countries and could get you into huge trouble. These transmitters are purely to be used for internal testing with a faraday cage!
Receivers:
By connecting speakers to the Portapack's 3.5mm audio jack you can easily listen in on standard NFM and WFM audio signals. ADS-B reception can be easily enabled on the PortaPack by selecting the inductor and lightning symbol on the top right. With the bias tee enabled you can receive aircraft.
Hardware Configuration:
1.TFT240*320 screen (model: ER-TFT024-3)
2. navigation switch (TSWB3NCB222)
3. audio output
4. microphone input
5. DC2.1 interface
6. 4 layer gold plate
7. ROSH process (exported to Europe and America)
The latest version is updated with the latest documents in 2017.5 month
Add a PortaPack to your HackRF One software-defined radio, and leave your laptop behind! The PortaPack attaches to your HackRF and adds a touchscreen LCD, navigation controls, headphone jack, real-time clock, micro SD card slot,
Just add a USB battery, and you're ready to explore radio spectrum wherever you are. The PortaPack firmware runs on the fast ARM processors in your HackRF. No computer is necessary (except for reprogramming firmware).
HAVOC Features:
- IQ file replay
- Microphone FM transmit with CTCSS
- CTCSS decoder
- Frequency manager (save & load from SD card, with categories and notes)
- File manager
- "Soundboard" wave file player (put 8-bit mono files in SD card /wav directory)
- ADS-B receiver with map view
- SSTV transmitter
- Fully configurable transmit signals
- POCSAG transmitter
- POCSAG receiver/decoder
- Morse transmitter (FM tone and CW)
- OOK transmitter for common remote encoders (PT2262, doorbells, remote outlets, some garage doors, ...)
- RDS (Radio Data System) PSN, RadioText and Time groups transmitter
- Meteorological radiosonde receiver for M10 and M2K2...
- AFSK receiver
- AFSK transmitter (Bell202...)
- Nuoptix DTMF sync transmitter
- TouchTunes jukebox universal remote
- LCR (Language de Commande Routier) message generator
- Street lighting control transmitter (CCIR tones)
- "Play Dead" in case of emergency
- Fully configurable RF signal generator
- RSSI audio output as pitch (for direction finding)
Specifications:
- 2.4 inch, 240 x 320 RGB LCD with resistive touch panel.
- Four-way arrow keys, rotary jog wheel, and select button.
- Preserving settings and date/time.
- Micro SD card slot for data and code storage
Some features demonstrated in 2016 February 22 firmware video:
- SSB, AM, narrowband FM, wideband FM audio reception, with spectrum waterfall.
- Wideband (18MHz) spectrum analysis and waterfall.
- Monitoring of boat (AIS), automobile (TPMS), and utility meter transponders (ITRON ERT).
- HackRF mode runs HackRF firmware for use with host computer SDR software.
- PPM calibration for more accurate tuning.
- Sleep mode saves power by turning off just the display.
You may also find the Furrtek HAVOC firmware very interesting!
Your HackRF will continue to function with computer-based SDR software, when you put the PortaPack into "HackRF Mode".
PortaPack is compatible only with the HackRF One. It is not compatible with the earlier HackRF Jawbreaker design. If you have an RF shield installed on your HackRF, the PortaPack should fit just fine. Compatibility with the HackRF Blue is experimental. One Blue owner has reported good results with minor mechanical interference between the PortaPack audio capacitors and the baseband header. If your HackRF Blue does not have a baseband header installed, you should have no mechanical problems.
PortaPack requires an external battery. Any USB-connected battery should work, though they vary widely in quality and poorly-designed batteries may inject voltage regulator noise into the radio.
The PortaPack and HackRF One will not replace your handheld ham radio receiver. Receive sensitivity varies from band to band, but will not perform as well as a true ham radio receive
Package List:
-1 x PortaPack
-1 x HackRF One
-3 x Antennas
-1 x Data Cable
-1 x Aluminum Alloy Case
Note: The PortaPack is assembled.
PortaPack + HackRF One SDR + Aluminum Alloy Case + Antenna + Data Cable Kit Assembled
Description:
-The official firmware created for the PortaPack has several decoders and transmitters built into it, but the third party 'Havoc' firmware is really what you'll want to use with it since it contains many more decoders and transmit options.
-You can fully unleash the power of the Portapack as this comes with Havoc Firmware Installed!
Progress of Work:
1. We have completed the program validation prototype.
2. The latest 2017.5 month documents are based on improvements.
Collect and Replay:
One of the best things about the PortaPack is that it makes acquisition and replay of wireless signals like those from ISM band remote controls extremely easy. To create an acquisition you just need to enter the "Acquistion" menu, set the frequency of the remote key, press the red 'R' Record button and then press the key on the remote. Then stop the recording to save it to the SD Card.
Now you can go into the Replay menu, select the file that you just recorded and hit play. The exact same signal will be transmitted over the air, effectively replacing your remote key.
Microphone TX:
Using the 3.5mm audio jack the Portapack can also be used as a standard Push to Talk or voice activated walkie talkie radio. With a microphone plugged into the audio jack simply hold down the right button to push to talk. If required you can also enable multiple CTCSS tone options, as well as tones that look like they enable transmission to wireless headphones
Other Transmitters:
There are generic OOK transmitter which can be programmed with custom data. This mode might be useful for experimenting with simple keyfobs, or things like home automatation switches.There are numerous transmit modes implemented that are questionable in most countries and could get you into huge trouble. These transmitters are purely to be used for internal testing with a faraday cage!
Receivers:
By connecting speakers to the Portapack's 3.5mm audio jack you can easily listen in on standard NFM and WFM audio signals. ADS-B reception can be easily enabled on the PortaPack by selecting the inductor and lightning symbol on the top right. With the bias tee enabled you can receive aircraft.
Hardware Configuration:
1. TFT240*320 screen (model: ER-TFT024-3)
2. navigation switch (TSWB3NCB222)
3. audio output
4. microphone input
5. DC2.1 interface
6. 4 layer gold plate
7. ROSH process (exported to Europe and America)
The latest version is updated with the latest documents in 2017.5 month
Add a PortaPack to your HackRF One software-defined radio, and leave your laptop behind! The PortaPack attaches to your HackRF and adds a touchscreen LCD, navigation controls, headphone jack, real-time clock, micro SD card slot,
Just add a USB battery, and you're ready to explore radio spectrum wherever you are. The PortaPack firmware runs on the fast ARM processors in your HackRF. No computer is necessary (except for reprogramming firmware).
HAVOC Features:
- IQ file replay
- Microphone FM transmit with CTCSS
- CTCSS decoder
- Frequency manager (save & load from SD card, with categories and notes)
- File manager
- "Soundboard" wave file player (put 8-bit mono files in SD card /wav directory)
- ADS-B receiver with map view
- SSTV transmitter
- Fully configurable transmit signals
- POCSAG transmitter
- POCSAG receiver/decoder
- Morse transmitter (FM tone and CW)
- OOK transmitter for common remote encoders (PT2262, doorbells, remote outlets, some garage doors, ...)
- RDS (Radio Data System) PSN, RadioText and Time groups transmitter
- Meteorological radiosonde receiver for M10 and M2K2...
- AFSK receiver
- AFSK transmitter (Bell202...)
- Nuoptix DTMF sync transmitter
- TouchTunes jukebox universal remote
- LCR (Language de Commande Routier) message generator
- Street lighting control transmitter (CCIR tones)
- "Play Dead" in case of emergency
- Fully configurable RF signal generator
- RSSI audio output as pitch (for direction finding)
Specifications:
- 2.4 inch, 240 x 320 RGB LCD with resistive touch panel.
- Four-way arrow keys, rotary jog wheel, and select button.
- Preserving settings and date/time.
- Micro SD card slot for data and code storage
Some features demonstrated in 2016 February 22 firmware video:
- SSB, AM, narrowband FM, wideband FM audio reception, with spectrum waterfall.
- Wideband (18MHz) spectrum analysis and waterfall.
- Monitoring of boat (AIS), automobile (TPMS), and utility meter transponders (ITRON ERT).
- HackRF mode runs HackRF firmware for use with host computer SDR software.
- PPM calibration for more accurate tuning.
- Sleep mode saves power by turning off just the display.
You may also find the Furrtek HAVOC firmware very interesting!
Your HackRF will continue to function with computer-based SDR software, when you put the PortaPack into "HackRF Mode".
PortaPack is compatible only with the HackRF One. It is not compatible with the earlier HackRF Jawbreaker design. If you have an RF shield installed on your HackRF, the PortaPack should fit just fine. Compatibility with the HackRF Blue is experimental. One Blue owner has reported good results with minor mechanical interference between the PortaPack audio capacitors and the baseband header. If your HackRF Blue does not have a baseband header installed, you should have no mechanical problems.
PortaPack requires an external battery. Any USB-connected battery should work, though they vary widely in quality and poorly-designed batteries may inject voltage regulator noise into the radio.
The PortaPack and HackRF One will not replace your handheld ham radio receiver. Receive sensitivity varies from band to band, but will not perform as well as a true ham radio receive
Package List:
-1 x PortaPack
-1 x HackRF One SDR
-1 x Aluminum Case
-1 x Antenna
-1 x Data Cable
Note: The PortaPack is assembled.
Description:
-The official firmware created for the PortaPack has several decoders and transmitters built into it, but the third party 'Havoc' firmware is really what you'll want to use with it since it contains many more decoders and transmit options.
-You can fully unleash the power of the Portapack as this comes with Havoc Firmware Installed!
Progress of Work:
1. We have completed the program validation prototype.
2. The latest 2017.5 month documents are based on improvements.
Collect and Replay:
One of the best things about the PortaPack is that it makes acquisition and replay of wireless signals like those from ISM band remote controls extremely easy. To create an acquisition you just need to enter the "Acquistion" menu, set the frequency of the remote key, press the red 'R' Record button and then press the key on the remote. Then stop the recording to save it to the SD Card.
Now you can go into the Replay menu, select the file that you just recorded and hit play. The exact same signal will be transmitted over the air, effectively replacing your remote key.
Microphone TX:
Using the 3.5mm audio jack the Portapack can also be used as a standard Push to Talk or voice activated walkie talkie radio. With a microphone plugged into the audio jack simply hold down the right button to push to talk. If required you can also enable multiple CTCSS tone options, as well as tones that look like they enable transmission to wireless headphones
Other Transmitters:
There are generic OOK transmitter which can be programmed with custom data. This mode might be useful for experimenting with simple keyfobs, or things like home automatation switches.There are numerous transmit modes implemented that are questionable in most countries and could get you into huge trouble. These transmitters are purely to be used for internal testing with a faraday cage!
Receivers:
By connecting speakers to the Portapack's 3.5mm audio jack you can easily listen in on standard NFM and WFM audio signals. ADS-B reception can be easily enabled on the PortaPack by selecting the inductor and lightning symbol on the top right. With the bias tee enabled you can receive aircraft.
Hardware Configuration:
1. TFT240*320 screen (model: ER-TFT024-3)
2. navigation switch (TSWB3NCB222)
3. audio output
4. microphone input
5. DC2.1 interface
6. 4 layer gold plate
7. ROSH process (exported to Europe and America)
The latest version is updated with the latest documents in 2017.5 month
Add a PortaPack to your HackRF One software-defined radio, and leave your laptop behind! The PortaPack attaches to your HackRF and adds a touchscreen LCD, navigation controls, headphone jack, real-time clock, micro SD card slot,
Just add a USB battery, and you're ready to explore radio spectrum wherever you are. The PortaPack firmware runs on the fast ARM processors in your HackRF. No computer is necessary (except for reprogramming firmware).
HAVOC Features:
- IQ file replay
- Microphone FM transmit with CTCSS
- CTCSS decoder
- Frequency manager (save & load from SD card, with categories and notes)
- File manager
- "Soundboard" wave file player (put 8-bit mono files in SD card /wav directory)
- ADS-B receiver with map view
- SSTV transmitter
- Fully configurable transmit signals
- POCSAG transmitter
- POCSAG receiver/decoder
- Morse transmitter (FM tone and CW)
- OOK transmitter for common remote encoders (PT2262, doorbells, remote outlets, some garage doors, ...)
- RDS (Radio Data System) PSN, RadioText and Time groups transmitter
- Meteorological radiosonde receiver for M10 and M2K2...
- AFSK receiver
- AFSK transmitter (Bell202...)
- Nuoptix DTMF sync transmitter
- TouchTunes jukebox universal remote
- LCR (Language de Commande Routier) message generator
- Street lighting control transmitter (CCIR tones)
- "Play Dead" in case of emergency
- Fully configurable RF signal generator
- RSSI audio output as pitch (for direction finding)
Specifications:
- 2.4 inch, 240 x 320 RGB LCD with resistive touch panel.
- Four-way arrow keys, rotary jog wheel, and select button.
- Preserving settings and date/time.
- Micro SD card slot for data and code storage
Some features demonstrated in 2016 February 22 firmware video:
- SSB, AM, narrowband FM, wideband FM audio reception, with spectrum waterfall.
- Wideband (18MHz) spectrum analysis and waterfall.
- Monitoring of boat (AIS), automobile (TPMS), and utility meter transponders (ITRON ERT).
- HackRF mode runs HackRF firmware for use with host computer SDR software.
- PPM calibration for more accurate tuning.
- Sleep mode saves power by turning off just the display.
You may also find the Furrtek HAVOC firmware very interesting!
Your HackRF will continue to function with computer-based SDR software, when you put the PortaPack into "HackRF Mode".
PortaPack is compatible only with the HackRF One. It is not compatible with the earlier HackRF Jawbreaker design. If you have an RF shield installed on your HackRF, the PortaPack should fit just fine. Compatibility with the HackRF Blue is experimental. One Blue owner has reported good results with minor mechanical interference between the PortaPack audio capacitors and the baseband header. If your HackRF Blue does not have a baseband header installed, you should have no mechanical problems.
PortaPack requires an external battery. Any USB-connected battery should work, though they vary widely in quality and poorly-designed batteries may inject voltage regulator noise into the radio.
The PortaPack and HackRF One will not replace your handheld ham radio receiver. Receive sensitivity varies from band to band, but will not perform as well as a true ham radio receive
Package List:
-1 x PortaPack
-1 x HackRF One SDR
-1 x Aluminum Case
-1 x Antenna
-1 x Data Cable
Note: The PortaPack is assembled.
PortaPack H2 3.2" Touch Screen 0.5PPM TCXO Clock For HackRF One SDR Transceiver (Expansion Board)
Features:
- With sound input and output function (ADC, DAC)
- With TF card slot (storage data, playback data, frequency management)
- Comes with TCXO high-precision clock (0.5ppm), the frequency is as accurate as the radio
- New firmware automatically switches the external TCXO (you can see the clock source is external in the menu)
- Support offline GPS simulation
- Optional acrylic black case
- Support for Apple or Android headset's MIC to send voice and headset to listen to sound
Supported App/Mode Specifications:
Receivers:
- For ADS-B receiver
- For ACARS receiver
- For AIS
- For AFSK
- For Analog audio receiver
- For POCSAG receiver
- For Radiosonde receiver
- For TPMS
- For APRS
- For DMR framing
- For SIGFOX
- For LoRa
- For SSTV
- For TETRA framing
Transmitters:
- For ADS-B transmitter
- For APRS
- For Xy/Ep transmitter
- For Jammer
- For Key fob
- For LGE tool
- For Microphone transmitter
- For Morse transmitter
- For Burger pagers
- For LCR transmitter
- For Close Call
- For Signal generator
- For Frequency manager
- For OOK encoders
- For POCSAG transmitter
- For RDS transmitter
- For Soundboard
- For SSTV
- For TEDI/LCR AFSK
- For TouchTunes remote
- For Custom remote
Others:
- Play Dead mode
- Pitch RSSI output
- Stealth mode
- Unistroke text entry
Package Included:
- 1 x H2 Expansion Board Touch Screen
Note: Other accessories are not included.
Features:
- With sound input and output function (ADC, DAC)
- With TF card slot (storage data, playback data, frequency management)
- Comes with TCXO high-precision clock (0.5ppm), the frequency is as accurate as the radio
- New firmware automatically switches the external TCXO (you can see the clock source is external in the menu)
- Support offline GPS simulation
- Optional acrylic black case
- Support for Apple or Android headset's MIC to send voice and headset to listen to sound
Supported App/Mode Specifications:
Receivers:
- For ADS-B receiver
- For ACARS receiver
- For AIS
- For AFSK
- For Analog audio receiver
- For POCSAG receiver
- For Radiosonde receiver
- For TPMS
- For APRS
- For DMR framing
- For SIGFOX
- For LoRa
- For SSTV
- For TETRA framing
Transmitters:
- For ADS-B transmitter
- For APRS
- For Xy/Ep transmitter
- For Jammer
- For Key fob
- For LGE tool
- For Microphone transmitter
- For Morse transmitter
- For Burger pagers
- For LCR transmitter
- For Close Call
- For Signal generator
- For Frequency manager
- For OOK encoders
- For POCSAG transmitter
- For RDS transmitter
- For Soundboard
- For SSTV
- For TEDI/LCR AFSK
- For TouchTunes remote
- For Custom remote
Others:
- Play Dead mode
- Pitch RSSI output
- Stealth mode
- Unistroke text entry
Package Included:
- 1 x H2 Expansion Board Touch Screen
Note: Other accessories are not included.
Payment Terms
1.We accept PayPal only.
2.All major credit cards are accepted through secure payment processor PayPal.
3.Payment must be received within 7 business days of auction closing.
4.We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
2.All major credit cards are accepted through secure payment processor PayPal.
3.Payment must be received within 7 business days of auction closing.
4.We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
Shipping Terms
-
For remote regions, we will charge your extra shipping costs. Usually
it cost about 35USD-50USD. We will contact you after your payment.
Thanks for your understanding.
Return Terms
1.
If you receive defective item, please kindly notify us within 14 days.
We will guide you the returning instruction for replacement or refund.
2. If you purchased in improper condition, please NOTE that the sipping and handling fee will not be refund, all return shipping fee should paid by the buyer unless item DOA.
3. We reserve the right to refuse any returns for objective reasons.
2. If you purchased in improper condition, please NOTE that the sipping and handling fee will not be refund, all return shipping fee should paid by the buyer unless item DOA.
3. We reserve the right to refuse any returns for objective reasons.
Custom Duties & Taxes
1.
Import duties, taxes, and charges are not included in the item price or
postage cost. These charges are the buyer's responsibility.
2. Avoiding some unnecessary trouble, please check with your country's customs office to inform us what we should declare its value before shipping.
2. Avoiding some unnecessary trouble, please check with your country's customs office to inform us what we should declare its value before shipping.
Feedback
1.
If you are dissatisfied for any reason, please don't be quick to leave
us neutral or negative feedback. We work hard to make sure EVERY
CUSTOMER 100% SATISFIED and resolve any problem for you and always leave
positive feedback to all our customers.
2. If you are satisfied with the product you received, please kindly leave us a positive feedback and 5 star DSR. If there is any problem of your order, please feel free to contact us firstly, we are responsible and credible seller, will follow it for you asap.
2. If you are satisfied with the product you received, please kindly leave us a positive feedback and 5 star DSR. If there is any problem of your order, please feel free to contact us firstly, we are responsible and credible seller, will follow it for you asap.
On May 22, 2023 at 00:39:23 PDT, seller added the following information: