CNC Z-Axis Tool Setting Touch Plate Probe Mach3 Router Mill.
CNC Router Engraving MACH3 Machine Tool Setting Auto-Check
Instrument 35mm Dia.
Cnc Z Axis Router Mill Touch Plate Mach3 Tool Setting Probe New Milling Hot Kit. Diameter：(Approx.) 35mm
Height：(Approx.) 20mm
Effective surface of the knife: 25mm diameter
Cable length 1.2 m , diameter 0.2 square feet,
Including alligator clips
connect the wire of this tool check insturment to the tool connector
of your
Control board of the machine , then the control board's GND
connect to the frame
of your router ( the frame of the router and the spindle must have
connections)
two ways to connect this item:
if your interface board has the limit switch port or other probe
port, you can
connect it to that port
if your interface board does not have that port, your driver board
has that port,
you can connect it to the driver board's limit switch port.
then in the Mach 3, you need to setup the probe(Mach3 --- Config--
-Ports and
Pins---Input signals Probe enabled , the pin number type the one
you use) and the
Package Included:1 x CNC router engraving machine Tool
Definitely use the new chips imported from Japan, Toshiba TB6560
With large heat sink to ensure good heat dissipation
Input signal high-speed optocoupler isolation, guarantee not losing steps
Semi-flow mode adjustable, semi-flow current adjustable, not the general design on the market, with a variety of semi-flow model and semi-flow current setting function
Attenuation model adjusted for all the motors can be locked when no noise
Ultra-small, the overall size: 62mm * 75mm, installation of four mechanical positioning hole size: 65mm * 55, hole size Φ3mm
The form of stud-type connectors and an optional plug-in
Rated voltage: DC 12V-24V
Maximum current: 3.5A
Current adjustable (Current Settings): 0.5A, 1A, 1.5A, 1.8A, 2A.2.5A, 3A
Subdivision adjustable (Excitation Mode): 1,2,8,16
Attenuation adjustable (Decay Mode):
0 %---- no decay mode
--- 25% of the slow decay mode
--- 50% of the normal mode
100% - Fast Decay mode
----- Decay mode of regulation by different motors to match impedance, thereby eliminating the noise when locked stepper motor and motor movement in the shake.
Automatic half current setting (Torque Settings):
%---- No pulse when the current 20 to normal operating current of 20%
50 %---- no pulse current 50% to normal operating current
75 %---- no pulse current 75% to normal operating current
100% --- no pulse when the current 100% to normal operating current
Package Included:1PCS* Single Axis CNC Router 3A TB6560 Stepper Stepping Motor Driver Controller Board
2, USB power supply and peripherals powered phase separation to protect computer security.
3, peripheral wide voltage input,12-24V, and anti-reverse function.
4, all of the input signal, all the light lotus isolated, which can be accessed emergency stop on the knife, the limit to protect computer security.
5, all the way to the relay output port, control spindle switch. Output port P17 mouth.
6, all the way through the optocoupler isolated 0-10V analog voltage output can be controlled with the corresponding analog interface converter to control the spindle speed. Output port P1 port.
7, open all 17 ports, which can be accessed with the optocoupler drive, 5-axis stepper motor can be controlled.
8, P1 as PWM outputs can be controlled with optocoupler input spindle governor.
9, can be accessed by a common cathode or common anode input level to 5V drive.
1 x CNC MACH3 Router Engraving Machine Tool Setting Auto-Check Instrument Probe
1 X USB cables.
1. PayPal payment accepted only.
2. Items will be shipped to your eBay address. Please make sure it is correct.
3. Payment must be received 4 days after auction ended.
1. Customer satisfaction is our top goal. We believe our items are so outstanding. All products are quality checked. They are new and in good condition when shipped to our customers. We are convinced you will be happy with your Purchase.
2. If product is defective or damage upon arrival, or wrong product shipped, please contact us immediately. Returns accepted within 14 days of delivery date and item must be in original new condition, not worn or altered in any way with attached tags & wrap. Otherwise deal is final. Return shipping must be paid by buyer.
3. Please contact us first if you have any problems/questions/concerns. We will be happy to resolve any issues you may have in a cordial and friendly manner.
4. We appreciate your Postive Feedback, and will do the same in return. DO NOT leave negative feedback without first communication with us. Please allow max 2 business days for us to response.
When you satisfied with our product and services please leave us positive feedback.
If a problem occurs, contact us immediately with any email request. Just contact us using the " Ask the seller a question" link on eBay.
On 26-Dec-2023 at 08:26:41 GMT, seller added the following information: