New 3D Printer Kit RAMPS + 2004 LCD Controller + MEGA 2560 R3 + A4988 Driver
Details
1.Mega 2560 control board CH340G version:
The Mega 2560 is an update for the Arduino Mega, which it replaces.
The board is a microcontroller board based on the ATmega2560-16AU .It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega is compatible with most shields designed for the Arduino Duemilanove or Diecimila.
The board is a microcontroller board based on the ATmega2560-16AU .It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega is compatible with most shields designed for the Arduino Duemilanove or Diecimila.
Product Summary:
CH340G replace the Atmega 8U2/16U2
CH340G Driver Download link, please copy the link and paste in browser: http://www.5v.ru/ch340g.htm
Microcontroller:ATmega2560
Clock Speed:16 MHz
EEPROM:4 KB
SRAM:8 KB
Flash Memory:256 KB of which 8 KB used by bootloader
Operating Voltage:5V
Input Voltage (recommended):7-12V
Analog Input Pins:16
Digital I/O Pins:54 (of which 14 provide PWM output)
DC Current for 3.3V Pin:50 mA
DC Current per I/O Pin:40 mA
CH340G replace the Atmega 8U2/16U2
CH340G Driver Download link, please copy the link and paste in browser: http://www.5v.ru/ch340g.htm
Microcontroller:ATmega2560
Clock Speed:16 MHz
EEPROM:4 KB
SRAM:8 KB
Flash Memory:256 KB of which 8 KB used by bootloader
Operating Voltage:5V
Input Voltage (recommended):7-12V
Analog Input Pins:16
Digital I/O Pins:54 (of which 14 provide PWM output)
DC Current for 3.3V Pin:50 mA
DC Current per I/O Pin:40 mA
2. Mega Pololu Shield Compatible (RAMPS 1.4 Shield)
It is a Mega Pololu Shield, or RAMPS for short,designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
3.2004 LCD controller
It is a Mega Pololu Shield, or RAMPS for short,designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
3.2004 LCD controller
This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the "smart adapter" included.
After connecting this panel to your Ramps you don't need your pc any more, the Smart Controller supplies power for your SD card. Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC, just with a g-code design stored on the SD card.
4. A4988 driver module
A4988 Stepper Motor Driver Board is a breakout board for Allegro’s A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection; please read the A4988 datasheet carefullybefore using this product.
Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered isasking for trouble.)
* Maximum output current is 1A
* Simple step and direction control interface
* Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
* Adjustable current control lets you set the maximum current output with a potentiometer,which lets you use voltages above your stepper motor’s rated voltage toachieve higher step rates
* Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
* Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
* Short-to-ground and shorted-load protection
3.LCD 2004 with Controller
After connecting this panel to your Ramps you don't need your pc any more, the Smart Controller supplies power for your SD card. Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC, just with a g-code design stored on the SD card.
4. A4988 driver module
A4988 Stepper Motor Driver Board is a breakout board for Allegro’s A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection; please read the A4988 datasheet carefullybefore using this product.
Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered isasking for trouble.)
* Maximum output current is 1A
* Simple step and direction control interface
* Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
* Adjustable current control lets you set the maximum current output with a potentiometer,which lets you use voltages above your stepper motor’s rated voltage toachieve higher step rates
* Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
* Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
* Short-to-ground and shorted-load protection
3.LCD 2004 with Controller
Package include:
1 x RAMPS 1.4
1 x LCD controller
1 x LCD controller
1 x MEGA 2560 R3 CH340G version
5 x A4988 driver
1 x USB cable
Payment
We accept PayPal only.
Shipping
1.Items are shipped from china.we will send out within 1 bussiness day after receive the payment.
2.We only ship to ebay confirmed address. So before bidding, please kindly verify your ebay address.
3.Shipping to most countries takes about 12-30 days via Economy Int'l Airmail.
Less than $40, without free tracking number,if you request tracking number,please send ebay message to us.
Over $40,with tracking number free.The shipping time depends on your location and local postal service,as well as the weather condition along the shipping,sometimes may take longer,.please send ebay message to us if the package was not arrived.
4.Express shipping: Extra $20 --$25 will be charged for the first 500 grams for most countries. Send ebay message to us if you need this service.
Terms of sale
1.If you are not satisfied when you receive your item, please return it within 30 days for a replacement or money back. Please send ebay message to us before you return it.
2.If item is defective in 30 days, We will send you a replacement without extra charger, or offer refund after we receive the defective item.
3.If item is defective after 30 days, you can still send it back to us. We will send you a new one after receiving the defective item. But you have to pay the extra shipping fee.
About us
We are honest seller and do our best to serve you.
So if you have any concerns,please don’t hesitate to send ebay message to us.
Am 17.11.17 hat der Verkäufer die folgenden Angaben hinzugefügt: