New RV LED Awning Light Set

16 feet of super bright RGB color changing LED Lights to light up your RV, camper, boat, deck or anywhere else you need light. 

Control colors, flashing modes, slow fades between colors, speed of transitions and more.


This is a RGB LED Light Strip 16' feet long that is fully Waterproof.  These lights are meant to last and does not need to be taken on and off or plugged and unplugged every time you open and close your awning. 

Here's what's included:

  • Either 24 or 44 key IR infrared remote

  • 16 feet of RGB Multi colored LED strips of either 3528 or 5050.

  • 1 x 12V standard U.S. wall plug.
3528 LED Light Strips:
They are called SMD3528 because the dimension of the chip is 3.5mm * 2.8mm. These LED chips (one LED per chip) are bright but not as bright as the 5050 side by side but when used in higher quantity can be brighter then a comparible strip of 5050s.

These lights are great for TV backlighting, color splashing walls, accent lighting for crown molding and pictures, under tables and cabinets, bars, etc.

5050 LED Light Strips:
Simply put, these LED chips are called SMD 5050 because the dimensions of the chips are 5.0mm x 5.0mm. They have 3 LED diodes in one housing (sometimes called tri-chips), and are a lot brighter than individual 3528 LED chips.

24 Key Remote

Input Voltage:DC 12V
Output Voltage: DC 12V
Output current: 6A(MAX.)
Control box dimension: 49mm x 34mm x 22mm ± 0.2mm
Remote controller dimension: 85mm x 52mm x 7mm
Remote controller battery: 1 x CR2025 (Included)

Directions:

When Switching to four dynamic mode(7 color jumpy change, all fade out & fade in, 7 color fade change, 3 base color jumpy), the button of " rightness" +"/" rightness" means the speed of light change is up/down, there are 8 steps in all.

 

44 Key Remote
Input: 12V
Output: 12V 
Max load current: 2A 
Mode & Pattern:
Color:20 Colors
8 Light Pattern: Quick / Slow / Auto / Flash / 7 color fade change / 3 color fade change
/ 7 color jumpy change / 3 color jumpy change R / G / B increase and decrease control 6

DIY keys 
Control range: 10cm - 500cm RGB LED Strips 
Support 5 -10 meters SMD 5050 /3528 30LEDs/M or 60 leds/M LED Strips

This kit is specifically designed for recreational vehicles.   The strip is held in place by it's adhesive 3M backing 

  • This strip can be mounted in many places; best place for mounting the LED Awning light is just under the Awning lip that is fastened to sidewall of your RV.  This will allow the LED awning light to be hidden and protected with the awning when closed and revealed when the awning is in the open position. This is the most permanent, safest and easiest place to mount the awning light. When locating the light on the sidewall side of the unit it produces much better light and will not shine in your eyes while sitting under your awning.
  • Select the location where you want to mount the light, take in account how you want to get the 12 volt power to this strip. We suggest starting the wire end of the strip near your RV power source.
  • Clean the mounting surface with 3M adhesive promoter if possible, if not just use rubbing alchohol. Remove the 3M backer and install end to end along the awning extrusion. Please be careful and plan ahead, this channel will not come off once it has been applied.
  • Remove the 3M backer from the LED strip, then apply.
  • Connect the Strip light wire lead to any 12V source and enjoy your new LED Awning light for 50,000 plus hours.
  • Note: This is very easy for any DIY to do.  

Don't forget to add any of our accessories like our 3ft or 16 ft -

4 wire extension so you don't need to wire your receiver box so high.  


We also sell additional IR and RF remotes that can be switched out 

for different uses as well as replacement plugs and adaptors.   Just 

ask us and we can send you a link or look in our ebay store.