DSLRKIT PSE8P2GUP Passive PoE Injector Switch

10/100/1000Mbps Ethernet Gigabit Uplink ports x2
Internal Power 52V Max.120Watt

 Support EXTEND mode, max Network Cable length to 250 meters

NOTE. When EXTEND mode enable, the Max bandwidth for the Power Link (PoE) port 1-8 network port will be reduced to 10Mbps for each one. Please check your IP CAMERA's  bit stream setting. We recommend the value does not over 8Mbps(8192Kbps).

When EXTEND mode is on (EXTEND indicator is on), 8 ports POE LAN is 10Mbps
When EXTEND mode is off (EXTEND indicator is off), 8 ports POE LAN is 100Mbps

(The up-link is not affected, it will always working at 1000Mbps max speed)


10 Ports (2 Gigabit Uplink, 8 100Mbps PoE)

Midspan Mode-B Unsolicited Power(4,5+/7,8-)

Compatible IEEE 802.3af/at, Per port Max 50Watt 

Wall Mount

(If you switch to the EXTEND mode, the Max allowable Network Cable length will increased to 250 meters. So we use 52V power. This will avoids the power loss over the long distances, and will make sure the PoE IP Camera working.)

((Please select according your device power consumption, in order to ensure device stable running, the total power consumption should not exceed 120watt of the power supply))


If your camera is with word “12V/PoE” as this picture shows, then please select this 52V PoE Switch, do not select 12V PoE Switch.
Because "12V/PoE" means it can offer power supply to camera via 12V DC port or 48V(or 52V) PoE Ethernet port

 

 

This is an Passive Power Over Ethernet of 10 port Ethernet switches, including 8 unsolicited PoE Ethernet ports and 2 Gigabit Ethernet Uplink ports. With an external 110V-240VAC to 52VDC power supply, any one of the 8 port can provide output power, each Ethernet port can provide network transmission speeds of up to 10 / 100Mbps , with Cat5 / 5e / 6 network cable.

Which compatible with IEEE 802.3af/at Mode-B(4,5+/7,8-) POE switch device, but it does NOT include the 802.3af/at compliant detection feature.  It supplies power NO MATTER WHAT, so don't plug the "Power Link 1~8" side into anything that isn't ready for it.

This POE switch only support 10/100M connection, PoE ports do not support Gigabit ethernet connection, because  "Power Link 1~8" port using 4,5,7,8 pin as power transfer, Please do not connect any "NONE PoE gigabit ethernet device and Uplink device" on "Power Link 1~8" port, this will damage your device.

Gigabit(1000Mbps) ethernet device Please do not access "Power Link port" this will damage your device.

Compatible all 802.3af/at device as Wireless Access Point, IP Phone, IP camera, Gateway , Switch, or More.....

Features:

  • 2 x 10/100/1000Mbps UPlink, 8 x 10/100Mbps Auto-negotiation Fast Ethernet RJ-45 ports with 8-Ports PoE function
  • Switch Controller Chips Realtek RTL8367N + RTL8309N
  • Support EXTEND mode, max Network Cable length to 250 meters. 
  • Midspan Mode-B Unsolicited Power(4,5+/7,8-)
  • Supports PoE power up to 120W for all PoE ports, Per port Max 52V 1A or 50Watt
  • Supports PoE IEEE802.3af/at compliant Powered Device (PD)
  • Each port supports auto MDI/MDIX, so there is no need to use cross-over cables.
  • Full/half duplex transfer mode for each port.

 

Specification:


ALL Port: can operate in full-duplex or half-duplex mode,must work with 4 pairs UTP Cat5/5e/6 cable。
Power Link Port 1-8: any supported unsolicited power on pairs 45-78 pins compliant Powered Devices (PDs)



Power LED LED ON: power on. LED OUT: power off
Green Light LINK/ACT LED ON Indicates the port is connected to a network device and has been started
LED OFF Indicates that this port is not connected to a network device or has not been started


Standard

IEEE 802.3 10BASE-T Ethernet

IEEE 802.3u 100BASE-TX Fast Ethernet

IEEE 802.3ab 1000Base-T Gigabit Ethernet (twisted-pair copper)

IEEE 802.3x Full-Duplex flow control

Protocol

CSMA/CD Ethernet

Data Transfer Rate

Ethernet: 10Mbps (Half Duplex) 20Mbps (Full Duplex)

Fast Ethernet: 100Mbps (Half Duplex) 200Mbps (Full Duplex)

Gigabit Ethernet: 2000Mbps (full duplex)

IC Chips

Realtek RTL8367N + RTL8309N 

Network Media(Cable)

10Base-T(EXTEND mode): UTP category 5e, 6 cable (maximum 250m) EIA/TIA-568 100Ω STP (maximum 250m)

100Base-TX:UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m)

PoE Power on RJ45

Power +: pin 4 & pin 5 ; Power -: pin 7 & pin 8

DC Output: 52V, Per port Max 1A or 50Watt, 8 POE ports Total Max. 120Watt

Number of Ports

2 x 10/100/1000Mbps UPlink, 8 x 10/100Mbps Auto-Negotiation RJ45 ports with 8 PoE enabled (port-1 ~ port-8)

Power Input

AC Input: 110V ~ 240VAC, 50Hz ~ 60Hz.

DC OutPut: 52V/2.3A

Power Consumption

3.2 Watts (max. no PD connected)

According to the actual power consumption of equipment

Temperature

Operation Temperature:0 ~40℃ (32 ~104℉)

Storage Temperature: -40 ~70℃(-40 ~158℉)

Humidity 

Storage Humidity 5%~90% non-condensing, Operating Humidity 10%~90% non-condensing

Product Dimensions

198mm W x 118mm D x 45mm H

RAM Register Capacity

64K bytes per device

MAC Address List

1K entries per device 

Frame Forward Rate

10Mbps Ethernet: 14880pps/Port

100Mbps Ethernet: 14880pps/Port

1000MBase-T Ethernet: 1,488,000/pps.


Item Included:

 DSLRKIT PSE8P2GUP 10pots 8PoE Unsolicited(Passive) PoE Gigabit switch x1
 AC Power Cable x1

AC power plug is US or EU type,if you need other type (AU or UK),Please leave a message.

12 Months Warranty from the date of purchase.