If your camera is with the word ldquo12V/PoErdquoas below picture shows,please choose to buy 48V PoE switch or the switch in comply with 802.3af /at standard, Please please do not buy 12V PoE switch.
DSLRKIT MID6P2U 12V Passive PoE Injector Switch
8 Ports (2Uplink, 6 PoE) 10/100Mbps
Midspan Mode-B Unsolicited Power pin(4,5+/7,8-)
12V6A 72Watt
12V Power Over Ethernet Max cable length of 30 meters
Wall Mount
This is an Passive Power Over Ethernet of 8 port 10 / 100Mbps-T Ethernet switches, including 6 unsolicited PoE Ethernet ports and 2Uplink ports. With an external 100V-240VAC to 12VDC power supply adapter, any one of the 6 port can provide output power, each Ethernet port can provide network transmission speeds of up to 10 / 100Mbps , with Cat5 / 5e / 6 network cable.
Which do not compatible with IEEE 802.3af and IEEE 802.3at, this is an unusual non-standard 12V unsolicited Power Over Ethernet switch. It supplies power NO MATTER WHAT, so don't plug the "Power Link 1~4" side into anything that isn't ready for it.
This POE switch only support 10/100M connection, PoE ports do not support Gigabit ethernet connection, because "Power Link 1~4" port using 4,5,7,8 pin as power transfer, Please do not connect any "NONE PoE gigabit ethernet device and Uplink device" on "Power Link 1~4" port, this will damage your device.
Gigabit(10/100/1000Mbps) ethernet device Please do not access "Power Link port" this will damage your device.
Compatible all 802.3af/at device as Wireless Access Point, IP Phone, IP camera, Gateway , Switch, or More.....
Features:
Specification:
| ALL Port: | Standard 10/100Mbps Ethernet port. Support 10Mbps Ethernet and 100Mbps Fast Ethernet, can operate in full-duplex or half-duplex mode,must work with 4 pairs UTP Cat5/5e/6 cable. | |||||
| Power Link Port 1-4: | any supported IEEE802.3af/at Powered Device and unsolicited power on pairs 45-78 pins compliant Powered Devices (PDs) | |||||
| Power LED | LED ON: power on. LED OUT: power off | |||||
| Yellow Light LINK/ACT | LED ON Indicates the port is connected to a network device and has been started | |||||
| LED OFF Indicates that this port is not connected to a network device or has not been started | ||||||
| Standard | IEEE 802.3 10BASE-T Ethernet | |||||
| IEEE 802.3u 100BASE-TX Fast Ethernet | ||||||
| IEEE 802.3x Full-Duplex flow control | ||||||
| Protocol | CSMA/CD Ethernet | |||||
| Data Transfer Rate | Ethernet: 10Mbps (Half Duplex)，20Mbps (Full Duplex) | |||||
| Fast Ethernet: 100Mbps (Half Duplex) ，200Mbps (Full Duplex) | ||||||
| Network Media(Cable) | 10Base-T: UTP category 3, 4, 5 cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) | |||||
| 100Base-TX:UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) | ||||||
| PoE Power on RJ45 | Power +: pin 4 & pin 5 ; Power -: pin 7 & pin 8 | |||||
| DC Output: 12V, Per port Max 1A or 12Watt, 6 POE ports Total Max. 72Watt | ||||||
| Number of Ports | 8 x 10/100Mbps Auto-Negotiation RJ45 ports with 6 PoE enabled (port-1 ~ port-4) | |||||
| AC Power Adapter | AC Input: 110V ~ 240VAC, 50Hz ~ 60Hz. | |||||
| DC OutPut: 12V/6A | ||||||
| Power Consumption | 3.2 Watts (max. no PD connected) | |||||
| According to the actual power consumption of equipment | ||||||
| Temperature | Operation Temperature:0 ~40℃ (32 ~104℉ ) | |||||
| Storage Temperature: -40 ~70℃(-40 ~158℉) | ||||||
| Humidity | Storage Humidity 5%~90% non-condensing, Operating Humidity 10%~90% non-condensing | |||||
| Product Dimensions | 132mm W x 66mm D x 32mm H | |||||
| RAM Register Capacity | 64K bytes per device | |||||
| MAC Address List | 1K entries per device | |||||
| Frame Forward Rate | 10Mbps Ethernet: 14880pps/Port | |||||
| 100Mbps Ethernet: 14880pps/Port | ||||||
|
|
|
|||||
Item Included:
8pots 6PoE Unsolicited(Passive) PoE switch x1
72Watt AC Power Adapter(DC OutPut: 12V/6A) x1
AC Power Cable x1
AC power plug is US or EU type,if you need other type (AU or UK),Please leave a message.