Description:pls check the pictures and descriptions of each select carefully before purchase)
Mini USB Cable
100% Brand New.
USB 2.0 Male A to Mini B 5-pin cable.
Allows you to transfer images and data between your cell phone, MP3，PDA, GPS systems to computer.
Up to 480 Mbps data transfer rate.
Hot-swappable cable.
Plug and Play.
Cable Length: 30cm
Color: Blue
Package Included:1*USB Cable
XBee S2 Wireless Module
This is the XBee XB24-Z7WIT-004 module from Digi. Series 2 improves on the power output and data protocol. Series 2 modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.These are essentially the same hardware as the older Series 2.5, but have updated firmware. They will work with Series 2.5 modules if you update the firmware through X-CTU.
Note: Series 1 and Series 2 XBee modules have the same pin-out. However, Series 1 modules cannot communicate with Series 2 modules.
3.3V @ 40mA
250kbps Max data rate
2mW output (+3dBm)
400ft (120m) range
Built-in antenna
Fully FCC certified
6 10-bit ADC input pins
8 digital IO pins
128-bit encryption
Local or over-air configuration
AT or API command set
Datasheet and document: please visit digi website
Package Included:1 X XBee 2mW Wire Antenna
XBee V03 Shield
3.3V and 5V dual power output
3.3V and 5V IO compatible
USB 2.0 protocol
BitBang mode ready
Easily connected to a PC via mini USB cable
XBee-setting support software X-CTU
Usage 1: PC via a USB cable directly connected with XBee adapters
Usage 2: Bluetooth Bee configure or use as a data-transmission
Uses 3: ARDUINO BOARD PRO MINI Downloader
Documents: Schematic
Mini USB Cable
100% Brand New.
USB 2.0 Male A to Mini B 5-pin cable.
Allows you to transfer images and data between your cell phone, MP3，PDA, GPS systems to computer.
Up to 480 Mbps data transfer rate.
Hot-swappable cable.
Plug and Play.
Cable Length: 30cm
Color: Blue
Package Included:1*USB Cable
XBee S2 Wireless Module
This is the XBee XB24-Z7WIT-004 module from Digi. Series 2 improves on the power output and data protocol. Series 2 modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.These are essentially the same hardware as the older Series 2.5, but have updated firmware. They will work with Series 2.5 modules if you update the firmware through X-CTU.
Note: Series 1 and Series 2 XBee modules have the same pin-out. However, Series 1 modules cannot communicate with Series 2 modules.
3.3V @ 40mA
250kbps Max data rate
2mW output (+3dBm)
400ft (120m) range
Built-in antenna
Fully FCC certified
6 10-bit ADC input pins
8 digital IO pins
128-bit encryption
Local or over-air configuration
AT or API command set
Datasheet and document: please visit digi website
Package Included:1 X XBee 2mW Wire Antenna
XBee V03 Shield
Bee Adapter is a compact USB to serial adapter equipped with BEE (20pin 2.0mm) sockets. With integrated FT232RL IC, It can be used for programming or communicating with board which basic Arduino but without USB interface, like Sniffer Nano. On the other hand, you may connect your PC to various wireless applications via the BEE compatible modules.
The Adapter also could support XBee interface. 3.3V and 5V dual power output
3.3V and 5V IO compatible
USB 2.0 protocol
BitBang mode ready
Easily connected to a PC via mini USB cable
XBee-setting support software X-CTU
Usage 1: PC via a USB cable directly connected with XBee adapters
Usage 2: Bluetooth Bee configure or use as a data-transmission
Uses 3: ARDUINO BOARD PRO MINI Downloader
Documents: Schematic
Package Included:1 x Bluetooth XBee Shield V03 Module Wireless Control For XBee ZigBee Arduino
USB XBee Bluetooth Adapter(FT232RL)
Bee Adapter is a compact USB to serial adapter equipped with BEE (20pin 2.0mm) sockets. With integrated FT232RL IC,
It can be used for programming or communicating with board which basic Arduino but without USB interface, like Sniffer Nano.
On the other hand, you may connect your PC to various wireless applications via the BEE compatible modules.
The Adapter also could support XBee interface.
Specification
3.3V and 5V dual power output
3.3V and 5V IO compatible
USB 2.0 protocol
BitBang mode ready
Easily connected to a PC via mini USB cable
XBee-setting support software X-CTU
Usage 1: PC via a USB cable directly connected with XBee adapters
Usage 2: Bluetooth Bee configure or use as a data-transmission
Uses 3: ARDUINO BOARD PRO MINI Downloader
Documents: Schematic
Package Included:1 x Arduino BTBee/Bluetooth Bee USB to Serial port Adapter FT232RL Compatible Xbee
Bee Adapter is a compact USB to serial adapter equipped with BEE (20pin 2.0mm) sockets. With integrated FT232RL IC,
It can be used for programming or communicating with board which basic Arduino but without USB interface, like Sniffer Nano.
On the other hand, you may connect your PC to various wireless applications via the BEE compatible modules.
The Adapter also could support XBee interface.
Specification
3.3V and 5V dual power output
3.3V and 5V IO compatible
USB 2.0 protocol
BitBang mode ready
Easily connected to a PC via mini USB cable
XBee-setting support software X-CTU
Usage 1: PC via a USB cable directly connected with XBee adapters
Usage 2: Bluetooth Bee configure or use as a data-transmission
Uses 3: ARDUINO BOARD PRO MINI Downloader
Documents: Schematic
Package Included:1 x Arduino BTBee/Bluetooth Bee USB to Serial port Adapter FT232RL Compatible Xbee
XBee Adapter(No chips)
This is a simple breakout board for the popular XBee product from Digi.
This board breaks out all 20 pins of the XBee to a 0.1" standard spacing dual row header .
The spacing between 0.1" header is 0.5"making it breadboard friendly.
We highly recommend using femle sockets to
avoid having to solder the XBee permanently to the breakout board .
Package Included:1 x XBee Adapter Shield Breakout Board For XBee Module
This is a simple breakout board for the popular XBee product from Digi.
This board breaks out all 20 pins of the XBee to a 0.1" standard spacing dual row header .
The spacing between 0.1" header is 0.5"making it breadboard friendly.
We highly recommend using femle sockets to
avoid having to solder the XBee permanently to the breakout board .
Package Included:1 x XBee Adapter Shield Breakout Board For XBee Module