Power i-TIG 200T

  
   







SKU: Plasma102i-CNC-Pkg



Product Description

If you are looking for a high capacity plasma cutter for a professional plasma table machine that keeps you on budget, the Everlast PowerPlasma 102i with the CNC package is definitely a strong competitor.  The portability, power, and performance, combine with the price to make the PowerPlasma 102i one of the best choices available in it's class when you consider cut capability to purchase cost ratios.  You get the best cut per amp per dollar paid for the PowerPlasma 102i CNC over any other 100 amp cutter in it's class. For routine daily use, the unit is recommended for cutting 3/4" thick plate metal.  And for maximum cut capability on CNC, this unit is capable of producing quality cuts of 1 1/8" or greater (at reduced speeds).   With a built in CNC socket and CNC torch this package is ready to be connected to your plasma table.  All you have to do is connect the plasma table control wires to the socket connector.  The unit's compact size lends itself to being stored or placed near the work area.  The new Italian designed iPT 100M machine/CNC torch is rugged and features improved consumable life with the patented "back striking" design.  This blowback design torch offers a variety of consumable choices, shielded and unshielded.  The performance and cut capability at the price level the PowerPlasma 102i CNC package is simply unmatched in the industry.

PRODUCT EXTRAS

Features & Benefits: 
  • Easy starting with Blow Back Pilot arc allows easy cutting of rusty and painted metals
  • Cuts virtually any type of metal with ease
  • Simple to use torches with inexpensive service parts and consumables
  • Commercial/Industrial class, 60% Duty cycle at 100 amps
  • Clean, smooth cuts and improved consumable life with the new Italian designed iPT 100M torch
  • Blowback start starts arc without the need of High Frequency which can interfere with surrounding electronics
  • Pilot arc improves performance and cutting on dirty, painted, or rusted metals 
  • 3 Second pilot arc tip saver feature shuts down pilot arc after 3 seconds of contiuous operation if no cutting is present to prevent premature consumable wear
  • Adjustable post flow control up to 50 seconds to improve consumable and torch life
  • Front air pressure gauge allows quick verification of air pressure
  • Over Current and Duty Cycle protection indicates fault with a dedicated warning/diagnostic light, and shuts down output until condition is resolved
  • IGBT modules from Infineon (Siemens) improve reliability and performance while reducing overall weight
  • CNC socket for CNC use on plasma tables (machine torch optional)

WHAT'S INCLUDED

Standard Equipment: 
  • 25ft. Italian designed and patented iPT 100M CNC torch with Euro quick-connect central adapter
  • Work clamp with 10ft. cable and DINSE connector
  • Air pressure regulator/water trap (Separate air dryer is required to reduce consumable wear and prevent torch damage)
  • Consumable starter kit
OPTION

Optional Equipment: 
  •  iPT 100 Hand-held torch
  • Welding cart
  • Consumable kit
RECOMMENDED USES
Recommended Areas of Use: 
  • Industrial Fabrication
  • Pipelines
  • Shipyards
  • Motorsports facilities
  • Repair shops
  • Rail Road maintenance
  • HVAC
  • Heavy Equipment Repair
  • Farm/Ranch
  • CNC
Recommended Metals: 
  • Steel
  • Stainless
  • Aluminum
  • Copper
  • Titanium
  • Nickel/Nickel alloys
  • Virtually any metal including cast iron
TECH SPECS
Type: 
IGBT
Voltage/phase: 
220/240 V 1 Phase
Output Amp/Volt Range: 

20-100A/88-120V

OCV: 

250V

Max Inrush ( I1MAX ) Amps: 
  • 220V 1 phase:  82A
Maximum Rated (I1EFF ) Input Amps: 

220V 1 phase: 64A

Duty Cycle At Rated Amps/Volts: 
  • 60% @ 100A/120V
  • 100% @ 80A/112V
Arc Start Type: 
Blow Back (Piston type)
PilotArc: 
Yes
Torch Type: 

Genuine Innotec iPT100

CNC Interface Port: 

Yes

Adjustable Post Flow Timer: 
No
Gouging: 
Yes
Recommended Cutting Air Pressure: 

70-75 psi

Recommended Compressor Capacity: 

8CFM @90 psi, 60-80 gallon tank

OK-to-Cut Indicator/Low Air pressure safety: 
No

NOTES


Notes: 

A separate air dryer must be provided by the customer to prevent torch damage, and excessive consumable wear. The unit includes a regulator/water trap, but is not designed to remove all water or moisture. Contact Everlast directly for Special orders with alternative voltages and phases. Additional charges may apply. Contact Everlast directly to order special units. Allow 6-8 weeks for special order deliveries.

If using with a generator, use a generator rated by its manufacturer as providing "clean power".  This is usually 5% or less THD (total harmonic distortion).

Use with a geneator rated for at least a minimum of 19,000 surge watts or greater.

This unit does not include a hand torch.
MINIMUM/MAXIMUM

  • Up to 3/4" daily use with CNC (rated for best cut speed and quality)
  • Up to 1 1/8" clean cut with CNC (edge start)
  • Up to 1 3/8" severance cut @ 3-5 ipm
  • Pierce up to 5/8"-3/4" with auto THC

    • Plasma cutting capacity is affected by several factors.  Ideal cutting conditions require dry air, new consumables, proper air pressure etc.   Quality of cut depends upon consumable orifice size, standoff height,  and travel speed. Ratings are for Steel.  Reduce capacity for Stainless by 25% and Aluminum by 40%.










Returns For returns, contact must be made within72 hours of delivery so an RMA number is issued. If there is damage, we can help file a damage claim immediately.

DOA items: In the event you receive a non working unit , we will exchange it free of charge.

Items returned must be in an GOOD condition. We will inspect all returns before accepting the package. We will not accept packages that have missing parts, damages, and packages that have not been approved for return by our initial contact or packages missing an RMA number. These packages will be refused and sent back to YOU at your cost.
Shipping Information: 1- We have an onsite professional shipping and packaging department and adhere to all shipping guidelines.
2- We will try to ship orders as soon as possible after payment approval unless otherwise stated in description. NOTE: Since there are many ways we offer our products, on rare occasions there is a chance an item may go out of stock that we have listed and sold on eBay. We will do our best to expedite backordered items as soon as possible.
3- Please provide a physical address. We will not ship to a PO Box.
4- Shipping charges are for the (48) Continental United States only.
5- We don’t ship to Canada
6- We charge CA tax on all orders 9.5%
7- If you pay via PayPal, shipping will be to your confirmed address only
8- Shipping to AK, HI and PR is more. please email for price.
Contact Operating Hours:
Monday through Friday: 9AM to 5PM PSTSaturday: 11AM to 4PM (PST)