Made in the USA
If you need the skin printed in a different size, let us know.
We can customize any skin with names or you organization logo. Let us know what you would like to add to the skin, and it can normally be added at no cost
Printed on the Highest Resolution Possible
Printed with Eco-Sol Ink
Printed on High Quality Vinyl
All Cornhole
Skins are sold as a set of two (2)
Contact us to mix and match any of our
designs for a custom set.
Looking for a specific logo, contact us and we
will list it for you.
For MORE of a selection
check out our store!!!!
All wraps are digitally printed with Latex
Ink on Automotive Grade Air Release Vinyl. This is the best ink
on the market. This special vinyl allows you to eliminate any
bubbles you may have, while trying to install, just by simply
pressing gently on them with your finger. All wraps have FREE
LAMINATE applied on top of them. All wraps must be applied dry
and to a very clean, smooth surface. Boards ARE NOT included.
Center hole is NOT pre-cut, which allows you to install the graphic to your custom built board, then cut the hole out with a razor blade....... For installation instructions please go to youtube and look for "apply cornhole board skins" you will find many ways to install these. Use the one that best fits your skills. We are not responsible for skins that have been improperly installed or messed up during installation.
Sometimes your screen color will NOT match colors perfectly, however when printed, the color will be the correct color
Our decals will NOT stick to plain wood, you must prepare the wood with one of the following:
GLOSS latex paint
Oil base paint
Polyurethane at least 4 coats thoroughly dried
We prefer to use the oil base paint as it sticks better and lasts longer, however, oil base paint it is unforgiving when it comes to sticking and once the decal touches the paint it is stuck in place so there is no room for mistakes in laying the decal. The Gloss paint however is a little more forgiving. You are able to pull it back off to straighten out bubbles or creases as long as you have not pressed it in place. Once the decal is exactly how you want it we suggest you smooth with a sponge or edge of a credit card with a soft towel wrapped around the edge. The Polyurethane needs at least 4 coats because it absorbs into the wood. The gloss will not appear until the third or fourth coat has been applied and for the best results of sticking.
No matter which prep you choose to do, the boards will need to be smoothed before and after the finish is applied with steel wool or a fine grit 220 or finer sandpaper before and after the paint/poly is applied. Remember every imperfection in the board or paint will show in the contour of the vinyl once it is laid so you want to be sure you have a smooth surface.
Cover our Skins with polyurethane at your own risk, they are covered with a lamination an do not need to be covered. we have seen GOOD and BAD results from doing this.
Sometimes your screen color will NOT match colors perfectly, however when printed, the color will be the correct color
We accept following payment methods mentioned below:
·
PayPal
·
Visa,
MasterCard, American Express and Discover via PayPal
·
E-Checks via
PayPal
PLEASE NOTE: If you are paying via E-Check
through PayPal, your order will not be shipped until
we get confirmation the E-Check had cleared the account.
It can
take 4-5 business days. If you want to get your order
fast please remit funds via credit card, instant
transfer or from your PayPal balance.
Check-Out Now: Click the Buy it Now button to immediately process with checkout and payment. This requires Immediate Payment.
Free shipping applies only to the lower 48
·
Contiguous US States.
Some items cannot be shipped internationally due
to size restrictions.
·
If payment is not received
within 24 hours of sale, available quantity will not
guaranteed.
Any and all contact must be made through the eBay
Contact Us link. We DO NOT check the webmail email.
ONLY THE EBAY MESSAGES MAIL.
· Overstock Outlet
will refund
the purchase price of the product minus a 10% restocking
fee.
·
All freight charges will be
covered by the customer.