ABS Estim Double Conductive 6mm Rubber Loop & Insulator

The resounding success and positive feedback I received about my insulated loops made me decide to design a double monopole loop. "Why would I want to use a double loop?" I hear you ask. Well, insulating a conductive rubber loop has only one drawback and that is that you lose half of the skin surface area so by doubling the loop up you get that back for a smoother ride. While still retaining all the benefits of insulating the upper half of the loop of course. This electrode insulator is made from ABS (think Lego plastic), it's hard-wearing, non-porous and doesn't need painting or any other finish. To produce these electrodes I have had to invest in new equipment and the post-print processing time to get the smooth non-porous finish takes me a long time and this is reflected in the price. If you prefer the best then this is the version for you. They will be available in very limited quantities so grab one while you can. These double loops are perfect for use as the common in a tri-phase configuration, just plug one cable from each (different) channel into each end of the loop. This cock loop insulator is printed in ABS. This insulator comes with a generous length of 20"/50cm of 6mm conductive rubber tubing that can be trimmed down to suit your anatomy. The high-quality British CR takes a 2mm plug. It will be dispatched with the 6mm conductive rubber tubing already fitted. The inner hole size is 1mm larger than the CR tubing, this 6mm tubing is a good friction fit and you don't need the plastic locking clamp to keep it in place once fitted but I will ship it with one fitted anyway. Material This product is 3D printed in ABS, a very strong plastic that has excellent mechanical properties. Once printed I post-process the components using a procedure called vapour smoothing. This uses Acetone vapour to actually melt and smooth the surface of the prints turning it from rough prints into smooth shiny prints that are non-porous. Porosity is one drawback of the 3D printing process as it leaves microscopic holes in the surface of prints that are perfect for bacteria to grow in and hard to clean. Vapour smoothing prints seals these microscopic holes and imperfections, leaving the products smooth and sealed. This is important as it makes cleaning post-play so much easier. Product Care After play simply wash in warm soapy water, anti-bacterial soap is best. Once body fluids have been washed off allow the electrode to dry thoroughly before you store it away for later use. A deep clean can be carried out using Isopropyl Alcohol, this will kill bacteria and remove body oils. Never use silicone-based lubes with conductive rubber-based electrodes as the silicone will bond to the conductive rubber, effectively destroying it and insulating it. Note: This product is supplied as is and I am not liable for any problems that arise from its use. It is sold as a novelty item and carries no warranty. Your statutory rights remain. Images shown are renderings.

ABS Estim Double Conductive 6mm Rubber Loop & Insulator

The resounding success and positive feedback I received about my insulated loops made me decide to design a double monopole loop. "Why would I want to use a double loop?" I hear you ask.

Well, insulating a conductive rubber loop has only one drawback and that is that you lose half of the skin surface area so by doubling the loop up you get that back for a smoother ride. While still retaining all the benefits of insulating the upper half of the loop of course.

This electrode insulator is made from ABS (think Lego plastic), it's hard-wearing, non-porous and doesn't need painting or any other finish. To produce these electrodes I have had to invest in new equipment and the post-print processing time to get the smooth non-porous finish takes me a long time and this is reflected in the price. If you prefer the best then this is the version for you. They will be available in very limited quantities so grab one while you can.

These double loops are perfect for use as the common in a tri-phase configuration, just plug one cable from each (different) channel into each end of the loop.

This cock loop insulator is printed in ABS. This insulator comes with a generous length of 20"/50cm of 6mm conductive rubber tubing that can be trimmed down to suit your anatomy. The high-quality British CR takes a 2mm plug.

It will be dispatched with the 6mm conductive rubber tubing already fitted.

The inner hole size is 1mm larger than the CR tubing, this 6mm tubing is a good friction fit and you don't need the plastic locking clamp to keep it in place once fitted but I will ship it with one fitted anyway.

Material

This product is 3D printed in ABS, a very strong plastic that has excellent mechanical properties. Once printed I post-process the components using a procedure called vapour smoothing. This uses Acetone vapour to actually melt and smooth the surface of the prints turning it from rough prints into smooth shiny prints that are non-porous.

Porosity is one drawback of the 3D printing process as it leaves microscopic holes in the surface of prints that are perfect for bacteria to grow in and hard to clean. Vapour smoothing prints seals these microscopic holes and imperfections, leaving the products smooth and sealed.

This is important as it makes cleaning post-play so much easier.

Product Care

After play simply wash in warm soapy water, anti-bacterial soap is best. Once body fluids have been washed off allow the electrode to dry thoroughly before you store it away for later use.

A deep clean can be carried out using Isopropyl Alcohol, this will kill bacteria and remove body oils.

Never use silicone-based lubes with conductive rubber-based electrodes as the silicone will bond to the conductive rubber, effectively destroying it and insulating it.

Note: This product is supplied as is and I am not liable for any problems that arise from its use. It is sold as a novelty item and carries no warranty. Your statutory rights remain. Images shown are renderings.