Universal Lichtdichtungsset zur Reparatur von Analogkameras

Enthaltene Materialien:

  • Neue Lichtdichtungen

  • Spachtel und Zahnstocher

  • Wattestäbchen 

Zusätzlich brauchst du:

  • Isopropylalkohol oder Klebstoffentferner

  • Schere

  • Pinzette

  • Kleiner Schlitzschraubendreher (optional)

  • Allzeckkleber (optional)

Anleitung:

  1. Öffne und entferne (wenn möglich) die Rückabdeckung der Kamera, um Zugang zu den alten Lichtdichtungen zu erhalten.

  2. Verwende einen kleinen Schlitzschraubendreher oder Spachtel, um die alten Lichtdichtungen vorsichtig abzukratzen. Achte darauf, den Kamerakörper oder andere Teile nicht zu zerkratzen oder zu beschädigen.

  3. Wenn die alten Lichtdichtungen besonders hartnäckig sind, kannst du Klebstoffentferner oder Isopropylalkohol verwenden, um den Klebstoff aufzuweichen. Trage die Flüssigkeit mit einem Wattestäbchen auf die Dichtungen auf und warte einige Minuten, bevor du erneut versuchst, sie zu entfernen.

  4. Reinige die Stellen, an denen die Dichtungen angebracht waren, mit Isopropylalkohol und einem Baumwolltupfer.

  5. Miss die Länge der alten Lichtdichtungen und schneide die neuen Dichtungen mit einer Schere auf dieselbe Länge.

  6. Verwende eine Pinzette, um die neuen Lichtdichtungen vorsichtig am Kameragehäuse anzubringen und achte darauf, dass sie sich an den richtigen Stellen befinden.

  7. Achte bei engen Dichtungsfugen (vor allem die Fuge der Rückwand), dass die Dichtungen sich nicht verdrehen. Du kannst sie mithilfe des Spatels reindrücken oder.

  8. Wenn du es nicht schaffst, die schmalen selbstklebenden Dichtungsstreifen in die Fuge zu drücken, kannst du beiliegende Wollschnur benutzen und sie mithilfe von flexiblem Allzweckklebstoff (z.B. UHU Kraft Alleskleber) einkleben.

  9. Hinweis: Es ist normal, dass sich die Rückwand der Kamera mit neuen Dichtungen etwas schwerer schließen lässt. Die neuen Dichtungen passen sich mit der Zeit von selbst an. 

  10. Setze die Rückabdeckung der Kamera wieder ein und teste die neuen Lichtdichtungen, indem du einige Testaufnahmen bei hellem Licht machst.

Das war's! Mit etwas Geduld und Sorgfalt kannst du die Lichtdichtungen an deiner analogen Kamera problemlos entfernen und erneuern.


Videoanleitung (veranschaulicht den Prozess; siehe Ende der Beschreibung): https://youtube.com/watch?v=Fj62Jq8dTMU&si=EnSIkaIECMiOmarE



EN: Universal Light Seal Set for Film Cameras



Materials included:

  • New light seals

  • spatula and toothpick

  • Cotton swabs


Aditionally needed: 


  • Isopropyl alcohol or glue remover

  • Scissors

  • Tweezers

  • Small flathead screwdriver (optional)

  • All purpose glue (optional)



Instructions:


  1. Open and remove (if possible) the back cover of the camera to gain access to the old light seals.

  2. Use a small flat-blade screwdriver or spatula to carefully scrape off the old light seals. Be careful not to scratch or damage the camera body or other parts.

  3. If the old light seals are particularly hard to remove, you can use adhesive remover or isopropyl alcohol to soften the adhesive. Apply the liquid to the seals with a cotton swab and wait a few minutes before trying to remove them again.

  4. Clean the areas where the seals were attached with isopropyl alcohol and a cotton swab.

  5. Measure the length of the old light seals and cut the new seals to the same length with scissors.

  6. Use tweezers to carefully attach the new light seals to the camera body, making sure they are in the right places.

  7. If there are narrow gaps between the seals (especially the gap in the back), make sure that they do not twist. You can press them in with the spatula.

  8. If you cannot press the narrow self-adhesive sealing strips into the joint without them being twisted, you can use the enclosed woollen string and glue them in place using flexible all-purpose glue (e.g. UHU Kraft All Purpose Glue).

  9. Note: It is normal for the back of the camera to be a little harder to close with new seals. The new seals will adjust themselves over time. 

  10. Replace the camera back cover and test the new light seals by taking a few test shots in bright light.


That's it! With a little patience and care, you can easily remove and replace the light seals on your analogue camera.



Video tutorial (the following video illustrates the process, see bottom of this description): 


https://youtube.com/watch?v=Fj62Jq8dTMU&si=EnSIkaIECMiOmarE

Kamera Lichtdichtungen und Spigelanschlagsdämpfer wechseln / How to Replace Light Seals (ENG SUB)

Video will open in a new window
Using the eBay App? Paste link into a browser window: