Description:
Features:
Please note that the flame will not be produced with vehicles still using the catalytic and those using a silencer at the tip of your aftermarket muffler.
Fitment Nissan:
Installation Instructions: (For Reference Only. Professional Installer is Highly Recommended)
First, the installation toolsThree meters
Frequency Table
Soldering iron
Scissors
Phillips screwdriver
Wire
Long nose pliers
Electric drill
Second, direct ignition and sub-disk ignition installation precautions
General car is divided into 1. Direct ignition 2. Sub-disk ignition
When installing this product in any vehicle, please note that the tail end of the exhaust pipe should not be too small. It is recommended to use a tail pipe with a diameter of more than five centimeters or an exhaust tail pipe.
Direct ignition installation Note:
When cut off the original car ignition coil power, "computer fault light" can not be bright.
Injector nozzle installation of positive and negative power should pay special attention to the wrong connection may be burned traffic computer possible.
Line through the fire wall should prevent the extrusion line destroyed, resulting in short circuit.
This product "test ear" installed in the bottom of the trunk, near the spare tire, to really fixed.
This product "igniter" should be locked at the end of the exhaust pipe about one centimeter away from the exit, the bottom, ignition spacing should be controlled at 2mm.
Ignition plate installation precautions:
Find out the ignition coil ignition coil in the right place.
Sub-ignition coil ignition coil to the product of the Spitfire control box wiring, must not go wrong, or sub-electric burns great possibility.
When cutting off the original ignition coil power supply, "computer fault light" can not be bright.
Line through the fire wall should prevent the extrusion line destroyed, resulting in short circuit.
This product "test ear" installed in the bottom of the trunk, near the spare tire, to really fixed.
This product "igniter" should be locked in the exhaust pipe at the end of about one centimeter away from the exit, the bottom, ignition spacing should be controlled at 2mm
Third, injector wiring installation
Fuel injector wiring installation:
You should first know that the injector nozzle signal line is positive or negative, most vehicles are negative.
How to know the injector nozzle two lines in the one for the signal line, first unplug the plug and then use the three meter side of the two positive and negative wires, such as a positive, a no power, No power supply should be the signal line, the other method is to use the frequency table to measure the fuel injector line two wires, the frequency of the signal line.
Nozzle positive and negative wire connection Spittoon control box on the color should pay special attention, can not pick the wrong wiring.
Spray nozzle wiring installation should pay special attention to positive and negative, the connection error may have burned traffic computer possible.
Fourth, fire-breathing method
★ ★ ★ Spitfire method:
Need hot car for more than 10 minutes, the exhaust pipe to be no water vapor.
Tune to 3500 ~ 6500 rpm, press and hold the switch light up and down the throttle one-third to half, (half a second look) eye visual speed, then the speed down from 6500 turn down, then listen To spit fire sound, the switch can be let go, while continuing to fill the throttle, then the speed will be pulled back to 6500 rpm, repeat this action can be sustained fire.
Note: Repeat the above action, if the speed fell to 1800 rpm, there is no flame, the switch must be let go, can not "press" to turn off the flame, serious damage to the engine.
Fifth, troubleshooting
In case of non-flameout must pay attention to:
Spittoon control box wire connector is missing or poor contact
Spitfire switch is damaged, the switch plug is dropped
Car after the test ear plugs have power, including positive and ground
Spitfire control box to the car after the test ear wire, with or without damage
Car after the test ear to the ignition wire is damaged
Ignition ignition pitch is too large or too small <2mm>
Injector nozzle connection is correct
Ignition coil in the sub-coil positive and negative wires are cut off the ignition lead to open circuit
Package include:
Destination | United Kingdom | Europe(except Island Countries) | |
Expected Time | 5-9 business days | 7-15 business days | |
Delivery may be delayed during weekends and holidays.We'll strive our best to provide you the most reliable, affordable way of shipping service. But sometimes it is highly depended on the courier companies and local customs,especially for international shipping. |
1.Please feel free to contact us if you have any question.Mails will be replied in 24 hours during business days and sometimes there may be delay during holidays and weekends.But we'll do reply you asap and try our best to solve your problems out. Believe us,every customer is taken as our important treasure.
2.Please check your mailbox or the messages in your ebay account if you've sent us emails or if there seems to be any problem.We'll keep all of you updated if there's any problems concerning logistics and so on.
3.Our mails are sent on Gmail,sometimes they may be blocked or could not be sent into a certain mailbox.Please change your settings or use another mailbox if you usually meet similar problems dealing on eBay.
For inquires and customer support, please send your email via ebay email system. All emails will be responded to within 24 hours during business days.