Condition: 100% brand new

Item type: Single Drive Drive Set

Material: plastic

Color: As picture shown

Weight: Approx. 172g 

Rated voltage: 24V
Product Category: Pedal Scooter
Remote control battery: built-in lithium battery
Capacity: 200mAh
Applicable people: universal
Current: 8A-12A
Speed: 3000rpm
Induction mode: for Hall
Maximum load capacity: 120kg

Large size of motherboard: Approx. 78x58mm/3.1x2.3in

Small size of motherboard: Approx. 35x20mm/1.4x0.8in

Functional product description:
1. Four gears, 1 low speed. 2 medium speed. 3 high speed. 4 player mode
2.EBS electronic brake (the battery will be charged when the brake is sliding downhill. The maximum valve current is 10A)
3. One key to turn forward/reverse direction
4. Wireless 2.4G remote control transmission control. 20 frequency points. Automatic frequency hopping anti-collision
5. Maximum valve current 40A
6. Controller features: low Speed and high torques
7. Maximum Speed: 3000 revolutions of hub motor (positive Xuanbo), 7500 revolutions of belt motor (rectangula).
8. One-key switch. Long press for 10 seconds to enter the paired remote control state (refer to item 20). The button LED working indicator is the connection status indicator with the remote control (flashing when the connection is successful, and the connection is unsuccessful, long on)
9. Hub motor. Choose by yourself without feeling or feeling (common for control boards)
10. Control method: sinusoid/rectangula
11. Equipped with motor. Hub motor 70.83.90. Motor. 80KV / model airplane motor 270KV or less, the effect is better

12. Three modes of control, four-wheel brushless controller integrated
Two modes: Hall sinusoid (automatic learning motor)
The second mode: Hallless rectangula (compatible with 99% motors on the market including non-inductive model airplane motors)
The third mode: there is a hall sinusoid fault repair mode (when one of the three halls of the motor is broken, it will repair and simulate the failed hall after the program is checked. If the two halls of the motor are broken, the program will automatically switch to No Hall rectangula mode)
13. The program is repaired by Hall. If the Hall is broken, one can operate normally/rectangula without affecting normal use.
14. Motor wire short-circuit protection. Motor wire off protection / stall protection / high valve current protection / battery under voltage protection / over current / over voltage / overload current limit protection.
15. Undervoltage buzzer alarm: a total of four alarm sounds, (one beep 40% power) (two beeps 30% power) (three beeps 20% power) (four dididi beeps) 10% power) Didididi will enter under-voltage protection after four beeps, which effectively protects the battery from over-discharge and damage to the battery. The same goes for the remote control low voltage alarm.
16. It is equipped with a mobile phone APP port, which can set various parameters of the control panel, and the remote control has two-way communication.
17. Description of remote control matching:
When the host is powered on, press the matching remote control button on the motherboard (the button is side to the buzzer) or press and hold the power button for 10 seconds. When the red LED is flashing, the host is waiting for remote control pairing, then tap the remote control Hide button (side to the remote control switch on), the main board LED light and the remote control LED light will flash at the same time, the remote control is matched successfully.
18. Naught power consumption standby: 10 minutes to enter the standby state. Standby power consumption is naught
19. No button sliding automatic switch:
1. After playing skateboarding, you don’t need to squat down and press the scooter shutdown button. The scooter will shut down by itself in 10 minutes. The shutdown power consumption is 0, and the standby power consumption is 0 when it is not on.
2. Every time you play skateboarding again, you don’t need to squat down and press the scooter power button, and lightly kick the scooter with your foot. The scooter will power on automatically and wait for the remote control order after powering on. Do not drive or interfere with the sliding of the motor, leaving the motor in the unpowered scooter mode
3. If the scooter is out of power, the kick scooter will still turn on, unless the battery protection board protects and there is no power output, after the scooter is turned on, it will not affect the user to regard the powered scooter as unpowered. There will be a low battery alarm sound on the mainboard, and the mainboard will not drive or interfere with the sliding of the motor without receiving a remote control order.
(Benefits: the scooter has been used for a long time, there will be a lot of mud or dirty at the bottom of the scooter, the advantage of kicking it on automatically)

5. Use environment:

Operating temperature range: -20°C to +120°C, normal operation ±5°C
Operating humidity range: 10% to 95%RH normal operation ±5 RH

How to connect the remote control and the controller board:
1. Connect the control board to the power supply.
2. Turn on the power of the control board and wait for 2 seconds. Then press and hold the switch for about 6 seconds until the power indicator flashes.
3. Turn on the remote control, and then use a small screwdriver to press the code synchronization switch on the lower left corner of the remote control.
4. Turn off the remote control for two seconds, and then turn it on again. Wait for the remote control signal light and the switch signal light to flash simultaneously, indicating that the matching is complet