*Item Details*
- Please check with your country customs office to determine what these additional costs will be prior to bidding/buying.
Note: This item is DIY Kit, not assembled. default with one PCB board.
Features:
This product is a booster coil production suite, the circuit is simple and reliable, with a professional line drawings, electronic research convenience enthusiasts
Uses: high school science experiment, electronic equipment, negative ion generator, scientific small production. This circuit is generated when the stable high frequency arc, high temperature, can easily ignite combustible materials, so it was called the plasma lighters
Parameter:
15KV transformer outside dimensions of approximately: 27×16×21mm
Input voltage: DC 3.7V-4.2V (limit 12v, easy to damage not recommended, this transformer is equally applicable to 12V input voltage, but requires a corresponding increase in the base of the feedback resistor to about 150Ω ~ 1.5KΩ, its resistance should be large to replace a small adjustment, or burned transistor or transformer)
Input Current: <2A
Output voltage: approximately 15KV (please pay attention to safety when used)
Output Current: ≤0.4A
High voltage bipolar ignition distance: ≤0.5 cm
When the product input termination 3.7V-4.2V power supply, the secondary high voltage output is not connected to high-voltage rectifier diodes and capacitors, output terminals levels ≤1.5cm long can produce purple high temperature arc, no crackling, but the temperature is very high , you can easily and instantly point cigarette paper, or even very thin wire burned Sparks (such as junior high school chemistry experiment thin wire in oxygen combustion scene, but not as good as oxygen so intense.)
Transformer structure:
There are two primary windings, a primary winding, a feedback winding, the secondary output of high pressure. Other: 15KV transformer designed for maximum output, limit output can not exceed 15KV, is one centimeter arc, a higher output voltage is likely to damage the transformer.
PCB board size: 4.2CM * 3.2CM * 0.16CM;
Installation Notes:
1). With the PCB board parts better production, in which the transformer line of thick line and thin line, this should pay attention to the other components by the board of silk symbols and parameters of welding on the line. Transformer board has done three pads, in which the middle of the pad hole is relatively large, the hole at the same time welding a thick enameled wire and a thin enameled wire, thick enameled wire and fine enameled wire do not use the same side, such as with the left Thick lines and the right side of the thin wire into or with the left side of the thin line and the right side of the thick line welding into, in short, do not use the same side of the thick lines and thin lines can be.
2). In order to prevent the output 2-wire distance too far, resulting in no-load, you can weld a 3P pin at the output.
3). After the success of the production, if the output access to a high-voltage capacitor and three high-voltage rectifier composed of voltage doubler circuit, you can produce DC high voltage, you can make anion generator, wiring diagram is as follows:
Package Include:
15VKE = 1 type step-up transformer x1
PCB Board X 1
120 ohm resistance X 1
UF4007 ultra-fast recovery diode X 1
N20 transistor X 1
Heat sink X 1
M3 * 6 screws X 1
Boat switch X 1
3-Pin X 1
We always send the item to the address you give us on PAYPAL to ensure the security of the item. If you have changed your address, or want us to ship to another address, please change to the new address when you pay us with PAYPAL, otherwise
we will not be responsible if the package is lost. Hope you can understand. We ship items to Worldwide. Thank you.
Warm Remind
Please note about the photo enlargement. In order to show all details, we have made photo enlargement.
Please read the description carefully about the details and dimension.
Please note about the color variation. The color of photos may vary from different monitor.
We also try our best to show the material in a color that is as close as possible to the original,
all our photos are made using light that is as close to natural as possible and avoid color variation.
Therefore, we will not accept returns based on color variation of your gem from the display on your particular monitor or particular photo.
Please use the link "Ask the Seller Question" or send "eBay message" in you "My eBay" to contact us if you have problems, special requests or suggestions, we are very glad to help you anytime. Due to the 12 hours time difference
between West and Asia we will reply you within 24 hours.
Please leave us the positive feedback and good detailed seller rating after you received our package and satisfied with it.
As you know, every seller works hard for the positive feedback. and if you have any question with the transaction or you do not satisfied with the item, please fell free to contact with me before you leave any feedback, i will responds you
within 24 hours,
If you have any question, please feel free to contact with me i will responds you within 24 hours. We take the weekends off,
so any questions sent then will be answered on Monday. Thanks for your patience!